Jenn-Air Heating Element

I ordered the part I was sure I needed through the Appliance Pro website. I was surprised the part arrived in just two days. FIRST UNPLUG THE OVEN.. I removed the baking racks then two screws holding the plate over the element. I then removed three screws holding the old element in place, then gently wiggle/pull the element free from the electrical connections in the back of the oven. (Note: You cannot see the connections at this point. You'll need to remove the terminal block cover on the... Read more

• Little to no heat when baking
• Oven not heating evenly
• Won't start

Replaced lower and upper element. Internet research suggested it was the control board. Thankfully it was a much quicker and cheaper fix. Read more

Followed the Appliance Parts Pros video and it took me about an hour from start to finish. I felt like the job was easy to accomplish. Read more

• Little to no heat when baking
• Oven not heating evenly
• Element will not heat
• Oven is too hot

I finally found the right serial number and found the part at Appliance Parts Pros. I was skeptical that they would send the element that had the correct rear brace fixture. when it came 2 days later i opened the box the Part was correct and it took about 15 minutes to replace since there are only two screws. My oven works fine now. THX Read more

Took out the old element and checked with olm meter determined bad, no continuity. Orded new Element from Appliance Parts Pros. Had new one in less than 2 days easy fix. Read more

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

The top part of our double wall oven quit working a couple years ago. We asked an appliance repair guy if he could find a replacement heating element and after a few days, he told us he couldn't. We switched to using the bottom and recently I started looking to purchase a new oven. On a whim, I decided to check the Interwebs and found several sites claiming to have the part that the appliance repair guy said didn't exist. I ordered from Appliance Parts Pros and a few days later the... Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

• Little to no heat when broiling

The upper element in the top oven burned out. This was likely due to sugary food that had gotten on the element when the food was moved in/out of the element. The element was coated in crusty, burned food and the element was cracked in six or so places. The oven is a Maytag Gemini double oven range. The model number appears to be MER6875AAQ based on our receipt and manual. We did not pull out the oven since it is difficult to do so in our kitchen. Taking out the old element only... Read more

Replaced the burner. Read more

• Little to no heat when baking
• Oven not heating evenly
• Oven is too hot
• Won't start

I'm a 66 year old woman (on a fixed income) and I'd never before repaired an oven bake element . My stove is 20 years old but I still found it was much more affordable to change the bake element rather than buying a new stove. I called the number on the website and talked to a very informative woman. She answered all the questions I had about my stove. She told me about the repair video on the website which had step-by-step instructions. I ordered a new element - received it within 4 days.... Read more

Replaced lower and upper element. Internet research suggested it was the control board. Thankfully it was a much quicker and cheaper fix. Read more

• Little to no heat when baking

First I removed the (3) wire shelves. Removed the bottom cover by removing the (2) screws in the back. This exposed the oven element. Removed the (2) screws holding the mounting bracket on the front of the element then removed the (2) screws on the silver bracket that holds the back of the element. I carefully pulled the element forward which pulls it out of the back of the oven. I pulled slightly on the (2) wires attached to the element in order to get a small amount of slack to remove them... Read more

• No heat or not enough heat
• Takes too long to dry

I had to pop the lid up from the front with a screw driver, and behind the element was a metal piece, a heat shield, that had two screws that had to be removed from the back. The little part with the blue round tag (part of the kit that came with the element) was easily removed with one screw. Likewise, the element had a single longer screw holding it in on the right, and on the left a little rod was sticking through a hole in the metal, and you can merely move it to the side and up the slot,... Read more

I ordered a replacement part, which arrived in a few days. My husband removed the burned out part and put in the new one. No problems! Read more

• Element will not heat

Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more