Jenn-Air Range Parts

Color: stainless steel. Measures about 2 inches in diameter.

This leveling leg screw threads into the appliance base to raise or lower the chassis, helping you stabilize the unit on uneven floors. Replace a missing, bent, or stripped screw to restore solid, level footing.

• Provides fine height adjustment when paired with the leveling leg/bracket
• Helps eliminate rocking, rattling, or vibration caused by an unlevel appliance
• Restores adjustability when original screw is stripped, bent, or missing
• Helps maintain proper alignment with cabinets/countertops by keeping the unit level

• Disconnect power; for gas units, shut off the gas supply before beginning
• Pull the appliance forward and carefully lift or tip to access the leveling hardware—use a helper to prevent tipping
• Remove the old screw; start the new screw by hand to avoid cross-threading, then adjust height with a wrench until level
• Verify all corners contact the floor and recheck level after repositioning the appliance

This reignition spark module controls the surface-burner ignition system, sending high-voltage to the igniters and re-lighting the flame if it goes out. Replace a weak or failed module to restore dependable burner lighting and safety re-ignition.

• Sends high-voltage spark pulses to the surface burner igniters when a knob is turned on
• Stops sparking once flame is detected and re-ignites if the flame is lost
• Helps resolve symptoms such as no spark at the burners, intermittent ignition, or continuous clicking
• Central control for multiple burner ignition circuits

• Disconnect electrical power and shut off gas supply before servicing
• Handle electronics carefully; avoid static discharge
• Note wire locations and terminal labels; move connectors one at a time to the new module
• Mount securely and ensure a proper chassis ground before testing burner ignition

This gas pressure regulator stabilizes incoming supply to your range or oven, delivering consistent burner flames. Replacing a failed regulator can restore proper heat output and reliable ignition across surface, bake, and broil burners.

• Regulates household gas supply to the appliance manifold for stable burner operation
• Helps maintain consistent flame height and heat in the oven and on the cooktop
• Protects downstream gas components from overpressure
• Failure symptoms include weak flames on all burners, oven or broiler not heating, or repeated clicking with no ignition

• Disconnect power, shut off gas supply, and allow the appliance to cool before servicing
• Observe flow-direction/orientation arrows and connect inlet/outlet ports correctly
• Apply an approved gas-rated thread sealant to threaded joints; avoid overtightening
• After installation, leak-test all connections with an approved solution—never use an open flame

Color: metallic. Measures about 11 inches wide by 2-1/2 inches high.

Restore a tight, heat-holding seal around your oven door. This replacement door gasket helps keep heat and moisture inside the oven for more consistent temperatures and reliable cooking performance. What it does

• Seals the gap between the oven door and front frame to contain heat and vapor
• Helps the oven reach and maintain set temperatures for even baking and roasting
• Reduces heat escape that can cause longer preheat times or temperature swings
• Replaces seals that are torn, frayed, flattened, or leaking heat around the door

• 1 oven door gasket

• Disconnect power and allow the oven to cool completely before servicing
• Open the door and remove the old gasket by releasing its retaining clips; note orientation
• Start at the top center and press the new gasket into place evenly—do not stretch it
• Close the door and check for a uniform seal all around; readjust as needed

This valve knob replaces a worn or broken control on a gas range or cooktop. It attaches to the burner valve shaft so you can turn the burner on/off and adjust the flame with smooth, reliable control.

• Couples to the surface burner valve shaft to select Off/High/Low and regulate flame
• Restores control when the original knob is cracked, stripped, loose, or missing
• Provides a secure grip and proper alignment with panel markings for accurate settings

• Turn all controls to Off and let the surface cool before starting; disconnect power if working near igniters
• Pull the old knob straight off the valve shaft—do not pry sideways
• Align the flat/D-shaped opening with the shaft and press straight on until fully seated; verify the Off position aligns with the panel
• If the knob does not seat easily, stop and recheck the part number and shaft style

This replacement grill grate restores a sturdy, level grilling surface on your cooktop or range. Replace a cracked, warped, or missing grate to maintain safe support and consistent heat over the grill area.

• Provides the elevated grilling surface above the heat source for stable, even cooking
• Keeps food positioned at the proper height for consistent searing and results
• Replace if cracked, broken, warped, or heavily corroded
• Helps resolve rocking/unstable surface or uneven cooking caused by a damaged grate

• Turn appliance off and allow all surfaces to cool completely before handling
• Lift off the old grate and clean debris from the support ledges or frame
• Set the new grate in the correct orientation; ensure it sits flat and stable
• Verify proper clearance around adjacent components before use

The Motor-Fan is an OEM component specifically designed for Whirlpool kitchen ranges. Located within the back wall of the oven cavity, the motor fan works to circulate air and remove excess moisture and smoke during the cooking process. Proper motor-fan functioning helps ensure efficient oven ventilation and performance.

Symptoms of a bad motor fan include:

• Excessive smoke or moisture left in the oven after cooking  
• Oven taking longer to preheat and cook due to poor air circulation
• Loud buzzing or grinding noises emanating from the fan

Causes of failure are normally wear and tear of motor windings or fan blade bearings from years of continuous use. Overheating can potentially reduce lifespan as well. 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The bake element is the lower heating element inside an electric oven cavity. Replacing a failed element restores consistent baking performance, proper preheat times, and reliable temperature control.

• Provides the primary bottom-oven heat source used in Bake mode
• Common failure symptoms: no heat during bake or very slow preheating
• Oven may not reach set temperature or cook evenly
• Visible damage may include blistering, cracks, or breaks in the element sheath

• Disconnect power at the breaker before servicing and allow the oven to cool completely
• Remove oven racks for access; take a photo of wiring to aid reassembly
• Remove mounting screws, gently pull the element forward, and transfer wires one at a time to the new element
• Ensure the element sits level and clear of cavity walls; do not overtighten screws; restore power and test Bake

This is the switch control knob that fits onto the control shaft so you can select appliance settings with a simple turn. Replace a cracked, stripped, or missing knob to restore positive, accurate control. What it does:

• Attaches to the control switch shaft so you can turn and select settings
• Transfers hand rotation to the switch for proper operation
• Helps maintain clear, consistent setting selection
• Common symptoms: cracked or broken knob, spins without turning the switch, loose or won't stay on, missing knob

• 1 switch knob

• Make sure all controls are Off and the appliance is cool; disconnect power if working near the control panel
• Pull the old knob straight off the shaft—do not pry or lever against the panel
• Align the new knob with the shaft and press straight on until fully seated
• After installation, rotate through settings to ensure smooth, secure operation

This control panel assembly is the front console that houses the oven/range user interface and display, restoring visible controls and user input so you can select cycles, set temperatures, and monitor settings. What it does

• Contains the control interface (buttons/touchpad and display) used to select functions, temperatures and timers.
• Re-establishes visible feedback and input when buttons are unresponsive or the display is blank or flickering.
• Helps restore control of oven/range functions when the console is cracked, damaged, or failing.
• Works as the direct replacement for the damaged or nonworking control console to return normal user operation.

• Disconnect power at the breaker or unplug the appliance before starting—electrical shock hazard.
• Handle the display and trim carefully to avoid damage; some wiring harnesses or connectors must be disconnected and reattached.
• Keep track of screws and retainers; a basic screwdriver set is usually required.

This upper oven broil element delivers direct, intense heat for broiling and top-browning. Replace a failed element to restore fast, even broiling performance and consistent top heat in your electric range or wall oven.

• Provides high radiant heat from the top of the oven during Broil for searing and browning
• May cycle on for top-browning during Bake (on some models)
• Typical failure symptoms: no broil heat or slow, uneven top browning
• Replace if the element is cracked, blistered, pitted, or sparks/arcs when energized

• Unplug the appliance or switch off power at the breaker before servicing
• Remove oven racks; unfasten the element's mounting screws/clips and gently pull the element forward
• Transfer wires one at a time and support them so they don't slip back through the oven liner
• Avoid bending the new element; secure brackets/screws, restore power, and test broil

This igniter switch assembly replaces a worn or failed switch that controls ignition to a gas burner or oven igniter, restoring reliable spark/ignition and consistent burner operation. What it does

• Acts as the electrical switch that signals the igniter or spark module to light a burner or oven
• Helps resolve intermittent or no-spark ignition symptoms and burners that fail to light
• Restores proper on/off switching for the ignition circuit when the original switch is damaged or worn
• Works as the direct replacement switch component in the ignition system

• One igniter switch assembly

• Disconnect power and shut off gas supply before starting any repair
• Use basic hand tools; handle wiring connectors carefully to avoid damage
• Verify part compatibility with your model before installation

This broiler pan restores a sturdy broiling surface in your oven. It holds food for high-heat broiling while the lower tray catches drippings to help reduce smoke and keep the oven cavity cleaner.

• Provides a durable surface for broiling under the broil element or flame
• Collects grease and juices beneath the food during high-heat cooking
• Replaces pans that are missing, warped, chipped, or heavily rusted
• Helps cut down on smoke and mess from burnt-on residue on a damaged pan

• Allow the oven to cool completely before handling
• Slide the pan onto the appropriate rack position per your model's instructions; no tools required
• Use oven mitts—surfaces and edges can be hot after broiling
• If your model uses a separate broiler grid or rack, position it on top of the pan before cooking

This replacement microwave door restores a secure seal and a clear view into the cavity. Replace a cracked, bent, or misaligned door to help the interlocks engage properly so the oven can start and operate safely.

• Provides the door assembly used to open/close the microwave, with viewing window and latch hooks that actuate the door switches
• Seals the cavity perimeter via the choke to help contain microwave energy when latched
• Common symptoms include: door won't close or latch, oven won't start or shows a door-ajar error, or visible damage to the door frame or glass
• Helps resolve issues caused by a warped/bent door, broken trim, or loosened components

• Disconnect power before servicing; do not remove the microwave's outer cabinet
• Support the door, lift it off the hinges, and protect hinge springs and latch areas from damage
• Transfer any model-specific trim or hardware from the original door if required
• Align hinges and latch hooks; verify the door closes flush and latches securely.