Jenn-Air Range Parts

This lower thermostat monitors and helps regulate temperature in the appliance's lower compartment by opening and closing an electrical contact. Replacing a failing thermostat can restore normal cycling and help the compartment maintain correct temperatures. What it does:

• Senses lower-compartment temperature and completes or breaks the circuit to control cooling cycles.
• Helps the compressor/fan cycle on and off to maintain set temperatures.
• A defective thermostat may cause warm temperatures, continuous compressor operation, or inconsistent cooling.
• Matches the OEM function and mounting location for lower compartment temperature control.

• Disconnect power to the appliance before beginning any service.
• Label or tag wires before removal and reconnect exactly to the same terminals.
• Handle the sensor and capillary carefully; avoid kinking or excessive bending. After installation, restore power and verify normal cycling.

This white control knob replaces a worn or missing knob so you can smoothly select settings on your appliance again. It restores dependable turning feel and a clean, like-new appearance on the control panel.

• Attaches to the control shaft so you can select levels or functions
• Common fix for cracked, stripped, loose, or missing knobs
• Helps when the knob spins freely or is hard to turn
• Maintains clear alignment with the panel's indicator marks

• Disconnect power and, if applicable, shut off gas before servicing
• Pull the old knob straight off the shaft
• Align the new knob with the flat or splined shaft and press on until fully seated
• Verify smooth movement from OFF through all settings

This pressure regulator controls incoming water pressure to the appliance's water/ice system, helping maintain steady flow for proper dispenser and ice maker operation. Replaces a worn or failing regulator to restore correct water delivery. What it does:

• Reduces and stabilizes incoming household water pressure for the appliance's water valve/ice maker
• Helps prevent overfilling, leaking, erratic dispenser flow, or poor ice production caused by excessive pressure
• Works with the water inlet system to ensure consistent fill cycles and reliable dispensing
• Compatible with models that use WP74006429 as the factory regulator

• One pressure regulator

• Shut off water supply and unplug the appliance before replacing the regulator
• Inspect fittings and tubing for damage; replace any worn connectors or seals
• Tighten fittings securely and check carefully for leaks after restoring water and power

Replacement control knob that restores reliable manual control of your appliance's settings. Fits the original shaft to provide a secure grip and accurate selection when the original knob is cracked, loose, or missing. What it does:

• Replaces a damaged or worn control knob so you can select temperature or burner settings with confidence.
• Provides a clear indicator alignment for correct setting selection and tactile feedback while turning.
• Helps resolve symptoms such as a cracked, loose, stiff, or missing knob that makes adjustments difficult or imprecise.
• Matches OEM geometry for a factory-like fit and operation when installed on the correct shaft.

• Always disconnect power to the appliance before servicing to avoid electrical shock.
• Remove the old knob by pulling it straight off the shaft; align the new knob with the indicator and push firmly until seated.

Thermal cutoff

The Oven Liner Touch Up Paint is an OEM part for Whirlpool ovens. This 2 oz warm white touch-up paint is designed to cover minor scratches, chips, and blemishes on the oven liner, restoring its appearance and protecting it from further damage. 

Causes of a bad oven liner include exposure to high temperatures, accidental impacts, and abrasive cleaning materials, which can lead to scratches, chips, and discoloration. Over time, these imperfections can worsen, making it necessary to use touch-up paint to maintain the oven liner’s integrity.

Symptoms of a bad oven liner include:

• Visible scratches or chips on the oven interior
• Discoloration or fading of the liner
• Increased difficulty in cleaning the oven liner
• Potential rust or corrosion in affected areas

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Filter is an OEM part for Whirlpool cooktops. This part is responsible for trapping grease and other airborne particles, ensuring that your kitchen remains clean and free from unwanted odors during cooking. It effectively captures grease and prevents it from accumulating in the exhaust system.

A bad grease filter can occur due to clogging, damage, or excessive wear. If you notice symptoms such as poor ventilation, persistent cooking odors, or visible grease buildup in the downdraft vent, it may be time to replace the worn-out or clogged grease filter with this genuine OEM part.

Symptoms of a bad grease filter include:

• Poor ventilation and airflow
• Lingering cooking odors
• Visible grease accumulation in the downdraft vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Control panel provides the appliance's main user interface, housing the touchpads and display so you can choose cycles and options. Replaces a cracked, faded, or unresponsive control surface to restore normal operation. What it does:

• Houses the touch controls and display and relays user commands to the oven/range control electronics.
• Commonly replaces panels with unresponsive or intermittent touchpads.
• Addresses symptoms such as a blank, flickering or unreadable display and visible panel damage.
• Restores a clean, readable interface for selecting functions and settings.

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Handle the display and overlay carefully to avoid scratching or damaging touch surfaces.
• Basic hand tools typically required; keep fasteners and mounting hardware for reassembly.
• The appliance still shows control errors after replacement, the main control board or wiring may need inspection.

The Surface Ignitor is an OEM part for Whirlpool ranges and cooktops. This component is responsible for generating the spark needed to ignite gas burners on the cooktop or oven pilot light.

Causes of a bad Surface Ignitor can include wear and tear over time due to repeated use during ignition. Physical damage is also possible.

Symptoms of a failed surface ignitor include:

• Inability to ignite any gas burners
• Repeated sparking sounds but no ignition
• Yellow burner flames instead of blue

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

A replacement switch/ignitor that restores spark ignition so gas burners or the oven will light reliably. Designed to replace a failed ignition switch and help recover consistent sparking for normal appliance operation. What it does:

• Sends the spark needed to ignite gas burners or the oven burner.
• Common symptom: burners or oven won't light or ignition clicks without sparking.
• Can fix intermittent ignition or complete loss of spark at the cooktop/oven.
• Works as the electrical switching/ignition component within the appliance's ignition circuit.

• Disconnect power and shut off the gas supply before beginning any work.
• Handle wires and terminals carefully; avoid bending or damaging the igniter wiring.

Color: gray. Measures about 2 inches in diameter.

This single electronic control replaces a failed console control to restore user input and cycle selection. It provides the appliance's primary interface for selecting settings and signaling the main control board. What it does

• Receives and processes user inputs to start and control cycles
• Sends commands to heating/motor/timing systems so selected cycles run correctly
• Can correct symptoms like unresponsive buttons, incorrect or no cycle starts, or intermittent control behavior
• Interfaces with the appliance's wire harness and mounting bracket for secure installation

• Disconnect power before removing the old control to avoid shock.
• Handle the control and printed circuit board carefully; avoid static discharge and mechanical stress.
• Removal typically requires control panel or console disassembly and unplugging the wire harness—keep fasteners and connectors organized.

This 6-inch surface coil element restores reliable heat to one burner on your electric range. Replace a burned-out or damaged coil to bring back consistent, even heating for everyday cooking.

• Provides cooking heat for a 6-inch burner position on electric ranges/cooktops
• Helps resolve a burner that won't heat or heats intermittently
• Addresses uneven heating or visible hot spots on the coil
• Replaces elements with visible breaks, blistering, or burned terminals

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• For plug-in coil models: lift the element, pull straight out of the receptacle, and remove from the support/drip pan
• Align the new element's terminals with the receptacle, push firmly until fully seated, and set into the support
• Inspect the receptacle and wiring for heat damage and replace any compromised components before use

Note: This part does not include the control board. It does include the membrane switch (touchpad) along with the panel. 

Color: Stainless Panel w/Black Membrane

This product is a Whirlpool oven control "panel" assembly. This is a genuine OEM product and is sourced directly from Whirlpool. This part is compatible with Whirlpool, Magic Chef, Admiral, and Maytag appliances.

This backsplash restores the rear trim behind a range or cooktop, protecting the wall and covering wiring openings for a clean, factory-look finish. It replaces a damaged, dented, or missing backsplash to improve safety and appearance. What it does:

• Covers the gap between the cooktop and the wall to block spills, splashes, and heat from reaching the wall surface
• Hides wiring and mounting holes for a neat, finished look
• Replaces bent, cracked, or corroded rear trim that can collect grease and grime
• Helps maintain proper clearance and original appearance of the appliance

• One single-piece backsplash

• Basic hardware and mounting locations are OEM-specific; confirm matching fasteners on arrival
• Turn off power to the appliance and move the unit away from the wall before removing or installing the backsplash
• Use care to avoid scratching the finish during installation; two people may be needed for larger ranges
• If mounting holes or brackets are damaged, replace those items before installing this backsplash

Replacement gasket that restores a tight seal to the appliance door and helps prevent water or air leaks. Replaces worn, cracked, or compressed seals so the door closes properly and reduces moisture or heat loss. What it does:

• Seals the door opening to stop leaks of water, steam, or heated air.
• Helps maintain proper temperature and efficiency by preventing air exchange.
• Reduces condensation, odors, and cycling caused by a poor seal.
• Common signs you need this part: visible gaps or damage, leaks around the door, excess moisture, or poor heating/cooling performance.

• Disconnect power and water (if applicable) and allow the appliance to cool before starting.
• Clean and dry the mating surface to ensure a proper fit; remove old adhesive or debris.
• Align the gasket into the door channel or groove and press evenly; avoid stretching the material.
• If the door or mounting hardware is bent or damaged, repair those parts before installing the gasket.