Jenn-Air Range Wire, Harness, Power Cord

This wire harness routes power and signals between the appliance's electrical components to restore reliable operation and proper control functionality. It replaces a damaged or worn harness to fix intermittent power, control failures, or burnt connectors. What it does:

• Connects control board, switches, motors and other electrical components so they communicate and receive power
• Restores lost or intermittent power caused by broken or frayed wires
• Resolves control or function failures when caused by damaged wiring or connectors
• Prevents arcing and poor connections from worn terminals or insulation

• Disconnect power (unplug appliance or switch off breaker) before any service
• Match connectors and routing to the original harness; secure using existing clips and holders
• Inspect mating connectors and boards for heat damage before installing the new harness

This replacement wire provides a direct electrical connection between appliance components to restore proper function and safe operation. Use it to replace a damaged or frayed lead that's causing intermittent or lost connectivity. What it does

• Carries electrical current between terminals or components to enable operation
• Restores a secure connection when the original lead is cracked, cut, or corroded
• Can stop intermittent power, no-starts, or erratic behavior caused by a damaged lead
• Helps prevent arcing or shorts when a worn wire is replaced

• One replacement wire as shown

• Disconnect power to the appliance before checking or replacing wiring
• Verify terminal orientation and secure connections; use correct connectors and insulation
• Replace only like-for-like wire gauge and routing to maintain safety and performance
• If pins, splices, or connectors are damaged, replace or repair them per OEM guidance

This wiring harness routes power and signals between the appliance control and components, restoring reliable electrical connections so controls and motors communicate correctly. It's a direct-replacement harness used where the original is damaged or worn. What it does:

• Carries control and power wiring between the console/control board and components
• Restores lost or intermittent function caused by broken, frayed, or melted wires
• Prevents short circuits from exposed conductors and improves connection stability
• Helps resolve symptoms such as no power to a component, intermittent operation, or visible wire damage

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Follow OEM wiring routing and connector locations; replace only with the identical harness
• Inspect connectors and terminal ends for damage and secure all plugs during reassembly

This wiring harness connects the refrigerator cooling/condenser fan motor to the main wiring, restoring power and signal flow so the fan can run and help maintain proper cooling. Simple replacement when the old harness is damaged. What it does

• Provides the electrical connection between the cooling/condenser fan motor and the appliance wiring.
• Replaces a damaged, melted or corroded harness that can cause the fan to stop running.
• Helps resolve symptoms such as a warm refrigerator/freezer, intermittent fan operation, or no fan noise when compressor is running.
• Ensures secure, correct plug-and-play connections when installed properly.

• One cooling fan wiring harness

• Always unplug the appliance or turn off power at the breaker before starting work.
• Disconnect the old harness connectors from the fan motor and cabinet wiring; note routing and securement before removal.
• Reconnect new harness making sure all plugs seat fully and any retaining clips or ties are re-used to prevent contact with moving parts.
• After installation, restore power and verify the fan runs and there are no abnormal noises.

This wire harness assembly connects the griddle element/control circuits so the griddle heats and responds to controls. It replaces damaged or worn wiring to restore reliable electrical connection and safe operation. What it does:

• Transfers power and control signals between the griddle element and the appliance wiring
• Common fix when the griddle won't heat or heat is intermittent
• Replaces frayed, melted, or burned wiring that can cause shorts or poor contact
• Ensures correct connector fit and routing for proper griddle operation

• One wire harness assembly as shown

• Disconnect all power before attempting service to avoid shock or injury
• Inspect connectors and routing; replace the harness if insulation or terminals are damaged
• Match connector ends and routing to the OEM wiring diagram during installation