Kenmore / Sears Cooktop Parts

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

Quick replacement by sliding out the old filters and sliding in the new filters. Read more

I installed a new clock timer and overlay the job took only a few minutes and a very easy repair. Useful hint take a picture of your clock timer before you start to make sure all your wires are put back in the right order . Charles B Lafayette Tn Read more

• Door stuck closed

Turn off breaker, remove all screws { 4 on mine } inside oven door holding oven and microwave to kitchen cabinet and slide oven assembly out of cabinet {on to a temporary shelf of {4} 5 gallon buckets/plywood/bricks/shims that I made on the floor atop a scrap of carpet} just enough to access the side and rear screws of microwave's protective metal housing, then remove a total of 16 screws { there were 2 screws just inside top of "opened" microwave door that were holding top flat silver metal... Read more

I was able to clean the Oven Temp Sensor with 99% alcohol. Then replaced All switches (after breaker was isolated). Put it all back the way I found it. Turned on breaker. Tested all functions and had no reports of Fan Code re-appearing since. Read more

My cooktop repair was a total success from start to finish. I reviewed and later followed the APP repair video, which helped me decide if I wanted to tackle the repairs and guided me right before I started. The APP phone staff member was very helpful verifying the parts I had identified online using the model number of my older GE Profile cooktop to locate and view the correct online exploded view diagram. I told him it was a pleasure working with him. The parts arrived within 3 days of... Read more

Ordered new bake element on 01/03/2021 and received on 01/05/2021. Thanks for the expedited service. My husband removed the old bake element and replaced with the new bake element. Took less than 15 minutes to remove and replace. Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

• Little to no heat when broiling

I wanted to get the upper oven baking element replaced; it hasn't been working for a few months. This double oven has had two other issues, there is a fan that comes on to cool the electronics panel, That fan has made excessive noise and it operates for 2-3 hours after the oven turns off. The other problem with the oven is the Self-Cleaning feature runs for about 15-30 minutes and then turns off with an error code. I've had a local appliance repair person in to address the error code and... Read more

With the help of Wendee and Karen, we finally figured out my model numbers and which parts where correct. I ordered the parts and all arrived the next day except for the Broiler element which arrived in 2 days. I installed the new Baking Element myself. Took longer to figure out which curcuit braker to turn off. In about 30 minutes I had a brand new Baking Element in my oven working perfectly. On the following day, I installed the Broiler Element. That took a bit longer as it sits in a metal... Read more

• Little to no heat when broiling

Come to find out after replacing the element, it is the control card Read more

I purchased 2 new light rocker switches, Because the heating element rocker switch was unavailable. First I removed the power source for safety. Then I simply pulled each switch out individually with a flathead screwdriver for leverage. I simply unplugged the wires from the old rocker switch, discarded the old rocker, plugged the wires into the new rocker switch, and pushed the new switch appropriately back into the control panel. I used the same steps for both rocker switches. Once... Read more

Slipped the old ones out, slid the new ones in. So simple, even my husband could do it! Read more