Kenmore / Sears Cooktop Parts

I always save original books and assembly sheets for appliances. That helped a lot ! The assembly sheets showed how the ovens went in, how they were attached to the cabinet and what to avoid so I didn’t bend trim piece. Original booklet showed how to replace oven doors and lights etc. Once the hinge assemblies arrived I started replacement after having read on the internet original hinges had some problems. So I had ordered both right and left hinges to avoid a possible problem with the... Read more

Ohmed the oven heat elements and oven sensor, they checked out fine. No broken or bad connections. Figured it had to be high limit switch opening or control panel. With Christmas meal around corner I ordered both. Oven working fine and my wife is happy. Read more

• Little to no heat when baking

Was real simple--unscrewed back screws, disconnected the bad element and reconnected the good element. Was not hard at all. Read more

Installed a new ignitor/orifice assembly. Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

Removed the front off the back panel, unplugged the old unit. Then using a blow dryer heated the old timer to peel the face /cover off and applied to the new clock. Plugged in the replacement clock. Replaced the front of the range. The only complaint I have is we were not informed that a new face would not be included and the old one would have to be removed and applied to the replacement clock. The face that was on the orginal clock has the buttons to set the clock and timer reversed from... Read more

• Element will not heat
• Little to no heat when baking
• Oven not heating evenly

Removed 2 sheet metal screw pulled element out about 2 inches. Removed two Spade connections. Removed the element from the oven. Inserted the new element into the over, connected the two spade connector. Reinstalled the two sheet metal screws. Set the oven to bake for testing and tested until the element turned red. Total time less than 5 minutes. Read more

• Noisy

I used a set of ring pliers to remove the old retaining ring, then spread the plastic ribs around the fan motor shaft with a small flat bladed screwdriver to ease removal of the old fan blade. I reversed the process to replace the blade, gently tapping a socket from my socket wrench set placed over the motor shaft and ribs with a small rubber mallet. I stopped when the shaft protruded about 1/8" beyond the plastic ribs of the new fan blade, then installed the new retaining clamp ring with the... Read more

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

Well, after searching for a model number on the range, had to pull the existing module for the part number. Ordered and was shocked to see it arrive the very next day (no, didn't pay for next day). Went back together a lot quicker then me taking apart! Read more

Found the parts I needed ordered them from your site Received them and installed in a few minuets and was done Read more

We took the old ones off and put the new ones on..it was easy to do ..I want to say that the girl (I think her name was Heidi) she was a big help ,she made sure that I had the right parts,I ask her to show me the picture to make sure that they look like the part ..She was a really big help. I did a survey when I ordered the parts to..Thank you for your help and the parts Anna P Read more

Replaced numerous items including this Inverter and two control boards but the Magnetron was the ultimate solution. The tip was clearly burned through when I removed the original. Read more

Bought replacement relay board, replaced it. Would not work, turned stove circuit breaker off then on again. Display panel showed stove was resetting waited for reset, tested the bake option twice to ascertain it was working correctly. It worked! Our grateful appreciation to the customer service rep who helped us with our questions and the shipping. Wish we had gotten her name. Read more

I ordered one of these and used two extra screws I had lying around and now I have a nice level stove! Thanks AppliancePartsPros.com! Read more