Kenmore / Sears Dishwasher Dispenser Parts

This lever connects to the dishwasher detergent dispenser mechanism and actuates the cup lid. A worn or damaged lever can prevent the dispenser from opening at the right time, reducing wash performance.

• Transfers motion from the timer/actuator to release the detergent cup lid
• Common symptoms: detergent remains in cup, soap door won't open, poor cleaning results
• Restores reliable dispenser operation during the wash cycle

• Disconnect power and turn off water before servicing
• Access typically requires removing the inner door panel to reach the dispenser linkage
• Note linkage orientation before removal; transfer any springs or clips
• Test dispenser door movement by hand before reassembling

For single drain outlet models only. For dual outlet port models you must order the complete pump and motor WD26X10013.

This replacement cover restores the appliance's exterior protection and appearance by shielding internal components and helping maintain safe operation. Designed to match the original form and mounting points for a direct-fit replacement. What it does:

• Shields internal parts from dust, spills and accidental contact.
• Helps keep wiring and controls securely enclosed to reduce risk of damage.
• Restores a flush, finished exterior when the original cover is cracked, broken or missing.
• Prevents rattling or snagging caused by loose or damaged panels.

• Disconnect power (unplug or shut off breaker) before starting any work.
• Installation typically requires basic hand tools (screwdriver/socket); follow factory service instructions for fastener locations.
• Handle edges carefully—parts may have sharp edges; support the panel during removal/installation to avoid scratches or dropped hardware.
• Reinstall all fasteners snugly but avoid over-torquing; verify panels align and clear moving parts before restoring power.

This junction box cover replaces the appliance's electrical access panel to protect wiring and provide a secure entry point for the power cord. It restores a finished, safe electrical connection area and helps prevent exposed wiring. What it does

• Covers and protects the appliance's electrical junction box from dust and accidental contact
• Provides the mounting location and opening for the power cord/strain-relief connection
• Secures wiring and helps keep wire connections contained and stable
• Common symptom: cover cracked, missing, or loose—exposed wires or inability to secure the power cord

• Disconnect power at the breaker or unplug the appliance before servicing electrical parts
• Remove mounting screws from the old cover and replace with the new cover; retain or replace strain relief as needed
• Inspect the cord and wiring while access is open; replace any damaged wiring or strain relief components
• Follow the appliance manufacturer's instructions and local electrical codes for safe installation

This wet agent dispenser replaces the washer's liquid fabric softener dispenser to restore proper dispensing during the rinse cycle. It helps keep softener contained until the machine is ready to release it, improving rinse-time performance. What it does:

• Holds and releases liquid fabric softener (wet agent) into the rinse cycle
• Ensures softener is delivered at the correct time for even distribution
• Stops leaking or premature release when the dispenser housing is intact
• Commonly replaced when the dispenser cracks, clogs, or fails to dispense

• Disconnect power to the appliance before starting any repairs
• Access method varies by model; remove dispenser drawer or top panel per your model's service instructions
• Inspect surrounding seals and clips; replace if damaged to prevent leaks

The Detergent Dispenser is an OEM part for Frigidaire dishwashers. It holds and releases detergent at just the right time during the dishwashing cycle to ensure all dishes and cookware are thoroughly cleaned. Located inside the dishwasher's control panel area, the detergent dispenser opens automatically to distribute detergent.

Causes of a bad dispenser can include buildup that clogs the release mechanism over time, broken components that prevent the door from opening fully, or damage from excessive force or impact.

Symptoms of a bad dispenser include:

• Detergent not dispensing or only partially dispensing during cycles
• Residue left inside the dispenser after washing
• The dispenser door sticking or failing to open as designed

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement housing restores the appliance's structural enclosure, protecting internal components and helping panels and controls align properly. Use it to replace cracked, warped or damaged housings so the unit fits and functions as intended. What it does:

• Provides the main structural enclosure and mounting surface for internal components and exterior panels
• Replaces cracked, dented or broken housings that can allow misalignment or rubbing of parts
• Helps reduce vibration and movement by restoring proper fit between panels and internal assemblies
• Keeps internal components shielded from debris and wear that can lead to downstream issues

• Disconnect power (and water, if applicable) before starting any repair
• Handle edges carefully; housing edges and sheet metal can be sharp
• Basic hand tools are typically required; follow the appliance service manual for disassembly/reassembly steps

This wet agent dispenser assembly holds and releases liquid wetting/conditioning agents into the wash at the correct cycle, helping deliver fabric conditioner or similar additives when needed. It replaces a worn, clogged, or damaged dispenser for reliable delivery. What it does:

• Holds liquid fabric conditioner/wetting agent and releases it into the tub during the rinse cycle
• Ensures timed dispensing so conditioners are added at the proper point in the cycle
• Helps prevent over-dispensing and visible residue in the washer tub or on clothes
• Commonly replaces dispensers that leak, fail to release liquid, or have broken mounting tabs

• One wet agent dispenser assembly

• Disconnect power to the appliance before beginning any work
• Remove and reinstall using basic hand tools
• Rinse any remaining liquid from the area and avoid skin/eye contact with chemicals
• Test a short cycle after installation to ensure proper dispensing and secure mounting

This dispenser door housing replaces a cracked or damaged refrigerator dispenser assembly to restore proper dispensing and appearance. It keeps the dispenser area sealed and supports the dispenser lever and chute. What it does:

• Provides the housing and mounting for the refrigerator dispenser assembly and lever
• Restores a secure chute to prevent leaks and keep dispensed water/ice directed into glasses
• Stops issues caused by cracked or broken dispenser housing, such as moisture inside the door
• Supports proper alignment of the dispenser lever and actuator components

• Disconnect power to the appliance before starting any repair
• Remove the inner door liner or access panel to access dispenser mounting screws; keep track of fasteners
• Inspect related gaskets and dispenser components for wear and replace if damaged

Also order retainer part number WP3400918

The Thermostat Housing is an OEM part for Whirlpool dishwashers. It encases the thermostat responsible for accurately monitoring water temperatures throughout cleaning cycles. 

Symptoms of a faulty housing include:

• Inconsistent or improper water heating  
• Delayed or incomplete cycles from temperature control issues
• Error codes or failure detection by the control board

Causes may involve cracks allowing steam penetration, loose mounting points compromising seals, or damaged seals leaking interior thermostat components. 

This OEM replacement fits Whirlpool, KitchenAid, Jenn-Air, and some Kenmore models as well.

This lid is the washer's top cover that protects internal components and keeps clothes contained during operation. It restores the washer's enclosure and helps maintain safe, splash-free cycles. What it does:

• Covers the washer tub and control area to prevent splashes and keep items inside during cycles
• Provides the surface that the lid latch/switch engages to enable normal operation
• Replaces cracked, warped, or missing lids that allow debris in or interfere with closing
• Helps maintain the appliance's appearance and proper function of the top access

• Disconnect power before starting any repair to avoid electrical hazard
• Lift off or unbolt existing lid per your model's service instructions; alignment may be required for proper closure
• Keep screws and small parts organized; some models use hinge pins or clips that must be reinstalled
• If your washer also has a separate lid latch or switch, inspect and replace it only if listed as defective