Kenmore / Sears Dishwasher Parts

This pulley guides the dishwasher door's balance cable so the springs can counterweight the door. Replacing a worn or broken pulley restores smooth, controlled door movement and helps prevent the door from dropping or feeling heavy.

• Guides the door balance cable/cord to maintain proper spring tension
• Helps the door open and close smoothly and evenly
• Visible cracks, wobble, or flat spots on the wheel indicate replacement

• Disconnect power and shut off water before servicing
• Remove the toe-kick to access the side spring/cable area
• Support the door and carefully relieve spring tension; note the cable routing through the pulley
• Install the new pulley in the original position and inspect related cable/link and spring for wear

This gasket creates a watertight seal between mating parts in the dishwasher's water system. Replacing a worn or damaged seal helps stop leaks during cycles and maintains proper wash performance. What it does:

• Seals the joint between components such as the sump, pump housing, or inlet assemblies
• Prevents water leakage under pressure during fill, wash, and drain
• Helps maintain spray pressure by reducing internal bypass
• Common symptoms include water on the floor or in the base pan, and a flattened, cracked, or brittle old gasket

• One gasket

• Disconnect power and turn off the water supply before servicing
• Access the gasket location and remove any retaining hardware
• Remove the old gasket and clean both sealing surfaces thoroughly
• Seat the new gasket evenly without twisting; tighten fasteners/clamps uniformly and run a test cycle to check for leaks

For Whirlpool made dishwashers. Assembly includes one spring, one retainer and one protective tip. Replace both springs at the same time to prevent uneven load.

includes seal

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

This miniature door switch is the snap-action interlock that tells the appliance when the door is closed. Replacing a worn or sticking switch restores reliable start/stop and proper door-status sensing for safe, consistent operation. What it does:

• Acts as the latch/interlock sensor for door open/closed status
• Signals the control to allow or prevent operation based on door position
• Typical symptoms include: won't start or shows a door message, stops when the door is bumped, or light/fan behavior doesn't match door position

• 1 miniature door switch

• Disconnect power before servicing. If working on a microwave, high voltage may be present even when unplugged—properly discharge the capacitor.
• Access the latch/interlock area; note wire positions and transfer one lead at a time to the new switch.
• Use a multimeter to confirm the switch changes continuity when pressed before reassembly.

This replacement bracket is used in Frigidaire-made dishwashers to secure an associated component or panel. Replacing a broken or missing bracket restores a tight fit, alignment, and stability so parts don't loosen, rattle, or shift during cycles. What it does:

• Provides a rigid mounting point for the connected part or panel
• Maintains proper alignment and stability during operation
• Helps reduce rattling or vibration from a loose component
• Replaces a broken, bent, rusted, or missing bracket

• 1 bracket

• Disconnect power and turn off the water supply before servicing
• Access and mounting location vary by model; refer to your service or installation manual
• Wear cut-resistant gloves; bracket edges may be sharp
• Save and reuse the original screws/fasteners; install in the same orientation and tighten securely

This dishwasher insulation is a sound-dampening blanket that reduces operating noise and helps contain heat and moisture, protecting surrounding cabinetry and restoring performance when the original insulation is missing, torn, or saturated.

• Helps absorb pump/motor and water-spray noise for quieter cycles
• Acts as a thermal and moisture barrier to limit exterior "sweating"
• Replaces damaged, compressed, or waterlogged insulation to restore design sound levels
• Common signs: louder-than-normal operation, visible missing/torn insulation, moisture around the toe-kick or adjacent cabinets

• Disconnect power at the breaker and shut off water supply before servicing; wear gloves.
• Access the insulation by removing the necessary panel(s); document original placement for reference.
• Position the new insulation in the same orientation; keep clear of hinges, wiring, and vent openings.
• Reassemble, secure/level the dishwasher, and run a test cycle to confirm quiet operation with no interference.

This lower front toe kick panel restores a clean, finished look at the base of the dishwasher and helps shield the bottom area from debris and bumps. Replace a cracked, dented, or missing panel to secure the opening.

• Covers and conceals the lower access opening at floor level
• Helps protect base components from accidental contact and household debris
• Restores appearance when the original panel is damaged or missing
• Common symptoms: visible gap at the bottom front, loose or rattling kickplate, bent or broken panel

• Disconnect electrical power before servicing
• Open the door to access and remove the mounting screws holding the old panel
• Position the new panel, align tabs/slots, and reinstall screws—do not overtighten
• The panel clears the floor and does not interfere with door operation

Color: Black

Color: Black. Other colors: For white use WP3369614.

Included with nut.

Bushing, Door spring

This fill and drain hose assembly connects a portable dishwasher to a sink faucet, delivering incoming water and routing wastewater back to the sink. Replacing a worn assembly restores a secure connection and helps prevent leaks during operation.

• Integrates inlet and drain hoses with a faucet coupler for quick, tool-free hookup
• Supplies water to the dishwasher and returns drain water to the sink
• Can address no fill or no drain symptoms caused by a damaged or obstructed hose/coupler

• Safety first: Unplug the dishwasher and turn off water before servicing
• Expect residual water; place towels/pan and relieve line pressure
• Ensure a compatible faucet adapter is installed; attach the coupler fully and verify a good seal
• Route hoses without kinks, secure the drain end to the sink, and check for leaks on first run

This hanger anchors the dishwasher's door-balance spring to the frame so the door opens and closes smoothly. Replacing a worn or broken hanger restores proper spring tension and helps prevent a door that drops, slams, or feels heavy.

• Secures the door balance spring to the dishwasher cabinet/frame
• Maintains correct spring tension for smooth, controlled door movement
• Helps fix a door that falls open quickly or won't stay in position
• Useful to replace when door balance hardware shows wear or damage

• Disconnect power and shut off water before servicing; remove the toe panel/kickplate
• Support the door and carefully relieve spring tension before removing parts
• Slide the dishwasher out if needed for side access; transfer the spring to the new hanger and reinstall
• Inspect the opposite-side spring/link and hinge for wear; verify door balance before reassembly

The Circulation Pump Assembly is an OEM component specifically designed for Bosch dishwashers. It is responsible for circulating water during the wash cycle and helping dishes get properly cleaned. 

Causes of a bad circulation pump assembly can include normal wear and tear, as well as damage from debris getting caught in the pump mechanism over time. 

Symptoms of a bad circulation pump assembly include:

• Inability to circulate water, resulting in poor wash performance  
• Loud noises or vibrations coming from the pump area
• Leaks around or below the pump housing

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. Replace yours today to restore optimal water circulation for thorough yet gentle cleaning.