Kenmore / Sears Endcap Parts

This right-side black end cap finishes and secures the end of a trim, rail or channel to restore proper fit and appearance. It prevents sharp edges and keeps the assembly aligned for reliable operation. What it does:

• Covers and protects the exposed end of a trim, rail or channel to reduce sharp edges and wear
• Helps hold the trim/rail in place so shelves, drawers or doors stay aligned and operate smoothly
• Stops rattling or movement caused by a missing or broken end cap
• Restores OEM appearance where the original end cap is cracked, warped or lost

• One right-side black end cap

• High-level replacement; typically snaps or slides into position without special tools
• Remove power or secure appliance parts as needed before working in the area
• Inspect mating trim/rail for damage and replace if worn to ensure proper fit

Right Hand Endcap - Color: Black

Color: White

This endcap is a direct-fit replacement housing end cap that helps protect and support adjacent components, keeping internal parts aligned and reducing wear. It restores proper fit and function where a damaged or missing endcap causes noise or misalignment. What it does

• Covers and protects the end of the housing to prevent debris entry and reduce component wear
• Helps maintain correct alignment of internal parts to minimize vibration and noise
• Replaces cracked, broken, or worn endcaps that can allow movement or rubbing
• Useful when visible damage or play is present at the housing edge

• Disconnect power (and water if applicable) before beginning any repair
• Basic disassembly of the appliance's housing or access panel is usually required; keep fasteners organized
• Inspect surrounding seals, gaskets, and mounting tabs for damage and replace if needed

This cap fits over the appliance housing connection to protect and seal the joint, helping prevent leaks and contamination. It restores a finished appearance and helps keep internal components clean and functioning properly. What it does:

• Covers and protects a connection point or fitting from dirt and debris
• Provides a simple seal to help reduce minor leaks or drips at the joint
• Helps secure a hose or fitting in place and prevents loosening from vibration
• Common symptom: visible crack, missing cap, or water weep/soiling near the connection

• Disconnect power and shut off the water supply before replacing parts on refrigerated appliances.
• Verify the cap matches the connection shape and snaps or slides fully into place.
• Use basic hand tools only; avoid forcing the cap to prevent damage.
• Inspect surrounding seals or fittings and replace if damaged.

This right-side end cap fits the dryer's drum assembly and restores proper alignment and support for smooth, quiet operation. It replaces a worn or damaged end cap to reduce drum wobble and related noise. What it does:

• Supports and positions the drum at the right end to maintain proper rotation
• Helps prevent rubbing, scraping, or metal-on-metal contact that can cause noise
• Restores secure mounting for associated rollers/bearings at the right side
• Can be replaced when the end cap is cracked, broken, or visibly worn

• One right-side end cap

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the dryer front panel or bulkhead
• Inspect related rollers, bearings, and mounting hardware; replace any worn parts to prevent repeat failure
• Reassemble panels and verify the drum spins freely and without unusual noise

This end cap panel covers and finishes the exposed edge of a control or cabinet panel for a clean, factory appearance while protecting edges from chips and wear. It restores the look and helps prevent debris buildup in the gap. What it does:

• Covers and protects the exposed edge of a control/cabinet panel to restore a finished appearance
• Hides fasteners and raw panel edges for improved cosmetics
• Prevents dirt and debris from collecting in the panel gap
• Common replacement for cracked, chipped, loose, or missing end caps

• One end cap panel

• Disconnect power to the appliance before starting any repair
• Remove adjacent trim or screws as needed; align end cap and secure with original fasteners
• Handle carefully to avoid scratching the finish; do not overtighten screws
• Replace any damaged clips or mounting hardware to ensure a secure fit

This is the right side end plate. For left side use WB37K15.

This is the left side end plate. For right side use WB37K14.