Kenmore / Sears Grille

This replacement toe grille installs at the bottom front of the refrigerator. The 30-inch black kickplate finishes the look and helps protect and ventilate the condenser area. Replace a cracked or missing grille to restore appearance and airflow.

• Covers the lower front opening and directs air through the condenser vents
• Shields base components from bumps and debris during everyday use
• Provides a clean, finished look along the floor line
• Common signs of failure: cracked or warped grille, broken mounting tabs, won't stay attached, or missing piece

• Disconnect power before servicing
• Remove the old grille by releasing retaining clips or removing screws; save any reusable hardware
• Align the new grille and snap into place or reinstall screws—do not overtighten
• Keep ventilation slots clear after installation

This 30-inch toe grille covers the lower front of the refrigerator, completing the built-in look while allowing proper ventilation to the condenser area. Replace a cracked or missing kickplate to protect components and refresh the appliance's appearance. What it does:

• Covers the base/kick area at the front of the refrigerator
• Provides venting to help air flow through the condenser compartment
• Shields internal components from bumps and debris
• Restores a clean, finished exterior when the original is damaged or lost

• 1 toe grille (30 in)

• Disconnect power and wear cut-resistant gloves before starting
• Remove existing mounting screws or release retaining tabs; save hardware for reuse
• Align tabs/clips with cabinet slots and press or fasten the grille until fully seated
• Ensure vents are unobstructed and doors open/close without interference after installation

This front grille replaces the toe-kick panel at the base of the appliance. It helps protect the condenser area from debris and provides a finished look across the bottom front of the unit.

• Covers and protects the lower front opening and condenser area
• Helps direct airflow to the condenser for proper cooling performance
• Restores a clean, finished appearance when the original grille is damaged or missing
• Common signs: cracked or broken grille, missing panel, or difficulty keeping the lower area clear of debris

• Unplug the appliance and turn off water supply before starting
• Open doors and remove any screws or clips securing the grille; pull to release
• Align new grille with mounting points; snap or screw into place
• Check for secure fit and proper airflow clearance

This kickplate grille mounts across the bottom front of the refrigerator. It restores a finished look and helps protect the machine compartment while allowing proper airflow through the condenser area.

• Covers the lower front opening to hide and shield internal components
• Vents air to support proper condenser airflow
• Replaces a damaged, cracked, or missing kickplate
• Common symptoms: broken tabs, grille won't stay attached, visible damage, missing piece

• Disconnect power before servicing
• Open doors to clear the grille; remove the old piece by releasing clips or removing screws
• Align the new grille with the mounting points and snap or fasten into place
• Ensure the grille sits evenly and doesn't interfere with door swing or airflow

This refrigerator kickplate grille mounts across the lower front of the cabinet to cover the machine compartment while allowing proper airflow. Replacing a broken or missing grille restores a clean finish and helps keep debris away from internal components.

• Covers the lower opening and helps shield the condenser area from bumps and debris
• Helps direct air through the base for proper ventilation
• Restores a clean, finished appearance across the bottom front
• Typical symptoms: cracked or scuffed grille, broken mounting tabs, loose or won't stay attached, missing

• Disconnect power and wear work gloves to avoid sharp edges
• Open doors; on many models, pull the grille straight out to release spring clips. If screws are used, remove them from the base rail
• Align tabs/clips and snap or fasten the grille into place
• The grille is secure and clear of door swing and air inlets

This fan grill assembly covers and directs airflow for the evaporator fan, helping protect the fan and maintain proper circulation inside the compartment. It replaces a cracked, broken or missing grill to restore safe airflow and component protection. What it does:

• Protects the evaporator fan from debris and prevents contact with the spinning blades
• Directs airflow for consistent circulation across the evaporator coils
• Can reduce rattling or vibration caused by a damaged or loose grill
• Helps avoid airflow restriction that contribute to cooling issues

• Disconnect power to the appliance before any service to avoid shock or injury
• Typically installs behind an interior access panel; gentle trim removal may be required
• Inspect mounting tabs and clips; replace any damaged fasteners for secure fit
• Handle plastic parts carefully to avoid cracking; do not overtighten screws

Color: white. Measures about 38 inches wide by 4 inches high.

This replacement grille covers the appliance's front vent opening to maintain airflow and protect internal components. It restores a clean, finished appearance and secure fit when the original grille is cracked, warped, loose, or missing.

• Directs airflow through the unit for proper ventilation
• Shields internal parts from debris and accidental contact
• Replaces a broken, warped, or missing grille
• Common symptoms include rattling, poor fit, visible cracks, or an exposed opening

• Disconnect power to the appliance before servicing
• Remove mounting screws or release retaining tabs; keep hardware for reuse
• Align the new grille with tabs or slots and secure without overtightening
• Restore power and confirm proper fit and clearance

The Grille is an OEM replacement part for Whirlpool refrigerators. It covers the gap between the bottom of the refrigerator and the floor, providing a clean and finished look to your kitchen. It helps protect the internal parts from dust and debris while also preventing small items from rolling underneath the appliance.

Symptoms of a bad toe grille include:

• Visible cracks or damage
• Discoloration or fading
• Missing pieces or gaps in the grille

A damaged or worn-out toe grille can occur due to regular use, accidental impacts, or general wear and tear over time. If you notice cracks, discoloration, or missing pieces on the toe grille, it may be time to replace it.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This 30-inch toe grille restores the finished look at the bottom front of a range or oven while protecting the lower cabinet area from debris. It's a direct-fit exterior trim piece that keeps the appliance appearance clean. What it does:

• Covers and protects the appliance lower front, hiding components and braces.
• Restores a damaged, missing, or dented kickplate to improve the appliance's appearance.
• Helps prevent debris buildup under the appliance and reduces visible gaps.
• Stops rattling or loose trim caused by broken or warped grille pieces.

• High-level replacement: typically installs from the front and secures with clips or screws.
• Disconnect power and move the appliance per the manufacturer instructions before doing any service that requires pulling the unit forward.
• Wear gloves to protect hands and avoid scratching the grille finish during installation.
• Retain or reuse original fasteners when possible; obtain OEM replacement hardware if fasteners are missing.

This lower front grille/kickplate replaces a damaged or missing kickplate to restore your appliance's appearance and protect the lower front panel. Durable black finish matches factory styling for a clean, finished look. What it does:

• Covers and protects the appliance's lower front opening and underlying components
• Restores cosmetic appearance if the original is dented, cracked, scratched, or missing
• Helps keep pets and objects from contacting components behind the panel
• Provides the factory look and fit for a seamless exterior

• Disconnect power to the appliance before beginning any service
• Typically fastens with retaining tabs and/or screws; align tabs and snap or secure as needed
• Use basic hand tools and protect surrounding surfaces during removal/installation
• Inspect and replace clips for a secure fit

The Refrigerator Front Leg Cover Assembly is designed to protect and enhance the front legs of your Samsung refrigerator. This genuine OEM part ensures a perfect fit, maintaining the stability and appearance of your appliance. Crafted from durable materials, the cover assembly guards against wear and tear, preventing scratches and damage to both the floor and your refrigerator legs. Installing this part is straightforward, allowing you to restore your fridge's original look with ease. The Refrigerator Front Leg Cover Assembly also helps to minimize movement and reduce noise, contributing to a more stable and quieter kitchen environment. By choosing this genuine OEM part, you ensure compatibility and longevity, keeping your Samsung refrigerator functional and aesthetically pleasing for years to come. Whether you need to replace a missing cover or repair a damaged one, this cover assembly is the ideal solution to maintain the integrity and performance of your refrigerator.

The Toe Grille Clip is an OEM part for LG refrigerators. This part secures the toe grille to the base of the refrigerator, ensuring it remains in place while providing easy access for cleaning and maintenance. 

Causes of a bad Toe Grille Clip can include breakage due to accidental impacts during cleaning or general wear and tear over time. 

Symptoms of a faulty Toe Grille Clip include:

• The toe grille coming loose or falling off
• Difficulty attaching or detaching the grille for routine maintenance
• Visible damage or deformation of the clip
• Unusual gaps between the grille and the refrigerator base

This OEM LG part is also compatible with some Kenmore models.

This replacement control panel cover protects the console area and restores the appliance's finished appearance. It shields buttons and electronics from spills, dust, and everyday wear so controls stay secure and accessible. What it does:

• Protects the control console and underlying electronics from dust, moisture, and impact
• Restores a clean, finished appearance when original cover is cracked, warped, or missing
• Helps keep buttons and switches aligned and functioning properly by securing the front housing
• Reduces risk of debris getting into the control area, which can cause intermittent operation

• Always unplug the appliance or disconnect power before starting work
• Basic hand tools typically required (screwdriver, nut driver); remove console or trim per service instructions
• Handle carefully to avoid scratching the new cover; align clips and fasteners before securing