Kenmore / Sears Microwave Parts

Careful placement of new screws into the inside of the outer door that now hold the frame assembly to the door secured the frame assembly to the outer door. All of the other parts I bought and replaced were a waste of money. I figured since I had them I might as well install them anyways. Easier than sending them back since I had the whole thing apart anyways. The part I really needed was no longer available, the outside door. The glass reinstalled into the retainers in the door without a... Read more

We followed the manufacturer's instructions about re-positioning the fan motor and installing the vent damper (easy). We constructed a duct system from the microwave to the outside of the house (challenging). We used 3.25" x 10" metal duct to start the system through the wall behind the microwave, where we added framing to reinforce a cut stud. We ran the duct up a closet wall and through its ceiling into the attic. We had to make an offset duct piece from 3.25" x 10" metal duct to clear a... Read more

Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch. Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were... Read more

• Won't start

Watched u-tube Read more

It wasn't easy because this microwave over-the-stove light was difficult to find at a reasonable price. However, I did find one at AppliancePartsPros.com. Since the price was so reasonable, I bought 4 bulbs plus an interior light bulb and paid the same shipping price for all. Everything works great. Read more

I took the plastic vent piece off the front of the microwave & removed the charcoal filter & put the new one in. Made sure that while I had it open I cleaned all the built up grease out of it before closing it back up. Took the 2 grease filters from underneath the microwave & replaced with the new ones. Read more

The replacement lamp fit perfectly. I had tried other replacement lamps from the hardware store but wasn't able to find one that would fit. The lamp socket on the microwave was slightly smaller than a standard bulb. Read more

Looked online and found that someone had experienced the same issue and had replaced the cooling fan assembly for the magnetron. I ordered the parts for the assembly (motor, fan, and support), and replaced them and this fixed the problem. It took about 10 minutes to replace the parts, but lowering the unit and disassembly took around 45 minutes. The most difficult part was getting the outer sheet metal cover back on after the repair, as it has a bunch of clips on each front edge that need to... Read more

Screwdriver Read more

Replaced it. Read more

Careful placement of new screws into the inside of the outer door that now hold the frame assembly to the door secured the frame assembly to the outer door. All of the other parts I bought and replaced were a waste of money. I figured since I had them I might as well install them anyways. Easier than sending them back since I had the whole thing apart anyways. The part I really needed was no longer available, the outside door. The glass reinstalled into the retainers in the door without a... Read more

• Tray won't turn

We ordered a new Roller Guide Assembly. Read more

I ordered part from you and replaced old part I ordered on a Friday afternoon (late ) and was pleasantly surprised to receive the very next day!!!!!! Read more

• Exhaust fan not working
• shuts off after a few seconds

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

I took the machine screws out of the outer panel for the right side only. Then pull the panel back a bit to release the lips from the front of the machine and had immediate access to the internal assembly that housed mounting nut. Order the new parts from AppliancePartsPro.com during the Thanksgiving week. Still received via FedEx in short time due to their same day shipping - which was greatly appreciated and surprising. Most small part places take a while to get the product out the door,... Read more

I remove the burnt melted rack holder and replaced it with the new one I ordered. I watched the how to repair on YouTube and was able to remove it with a pair of pliers and install the new rack holder. It was very easy to install. Read more