Kenmore / Sears Range Parts

Needed to replace burner box panel (pan under electric coil burners) and replace stove top (black panel that surrounds the burners). BB was corroded, had a couple big holes from liquid boil-overs (salted water) from the last 10 years. The stove top looked nasty. It was chipped & scratched badly. Removed electric coil burners and drip pans from stove top. Removed 1 small Phillips screw in each burner opening to detach electrical burner sockets from stove top. Lift stove top and support on prop... Read more

I purchased 2 new light rocker switches, Because the heating element rocker switch was unavailable. First I removed the power source for safety. Then I simply pulled each switch out individually with a flathead screwdriver for leverage. I simply unplugged the wires from the old rocker switch, discarded the old rocker, plugged the wires into the new rocker switch, and pushed the new switch appropriately back into the control panel. I used the same steps for both rocker switches. Once... Read more

Quick replacement by sliding out the old filters and sliding in the new filters. Read more

Removed side moldings top molding and glass, removed broken handle. Reinstalled new handle, all modings and glass. Read more

Searched internet for answers. Decided to replace the door switch. Drier now runs great! Read more

The instructions that came with the replacement smaller surface heating element provided no help about how to open the top of the range, so I checked the internet. I found several videos on replacement of surface elements in flat top ranges, but none for our particular range, so I Google-searched a simple question, “How to open the top of a 6898VVD Magic Chef range”. The AI Overview answer had several points, most of them not useful, except for the last one: “Hidden Clips: There might be... Read more

Watched videos online and with that knowledge it was a very simple process. Read more

Ordered new burner tubes and it was a easy install. Read more

Removed drawer and did a simple part to part replacement of the drawer glides Read more

With the help of Wendee and Karen, we finally figured out my model numbers and which parts where correct. I ordered the parts and all arrived the next day except for the Broiler element which arrived in 2 days. I installed the new Baking Element myself. Took longer to figure out which curcuit braker to turn off. In about 30 minutes I had a brand new Baking Element in my oven working perfectly. On the following day, I installed the Broiler Element. That took a bit longer as it sits in a metal... Read more

Ordered new bake element on 01/03/2021 and received on 01/05/2021. Thanks for the expedited service. My husband removed the old bake element and replaced with the new bake element. Took less than 15 minutes to remove and replace. Read more

I installed a new clock timer and overlay the job took only a few minutes and a very easy repair. Useful hint take a picture of your clock timer before you start to make sure all your wires are put back in the right order . Charles B Lafayette Tn Read more

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

My cooktop repair was a total success from start to finish. I reviewed and later followed the APP repair video, which helped me decide if I wanted to tackle the repairs and guided me right before I started. The APP phone staff member was very helpful verifying the parts I had identified online using the model number of my older GE Profile cooktop to locate and view the correct online exploded view diagram. I told him it was a pleasure working with him. The parts arrived within 3 days of... Read more

• Won't start

First, it was going to cost $95 for an appliance guy just to look at it! I figured there would be an upcharge on the parts + labor on top of the $95, so I took a chance & decided my husband & I could fix it cheaper; we were right, but it was a 3 week process (luckily, we have another microwave in the basement we were able to use in the meantime). I googled the microwave model #, then price checked the same item I thought we needed; printed off the diagrams of the various microwave "systems" &... Read more

• Element will not heat

Purchased a new Element surface and installed same... All Okay now... Read more