Kenmore / Sears Refrigerator Gasket & Seal

Color: Black

The gasket is an OEM part for Whirlpool refrigerators. It is a sealing gasket responsible for creating an airtight seal between the refrigerator door and frame. This helps maintain proper temperatures inside the refrigerator and freezer compartments. 

Symptoms of a bad gasket include:

• Inability to maintain proper interior temperatures 
• Frost or condensation buildup inside the refrigerator or around doors and frames
• Higher electric bills from the compressor running excessively
• Noticeable temperature fluctuations when opening and closing the door

Causes of a bad gasket can include shrinkage and cracks due to aging, as well as tears, breaks, or holes from repeated use and compression. Over time, seals may no longer fully adhere, allowing air and warmer temperatures to enter.

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement gasket seals the appliance door to help maintain proper temperature and prevent leaks, keeping the interior efficient and protected. Use it to restore a tight door seal and reduce energy loss from gaps. What it does:

• Forms a secure seal around the door to keep heat or cold inside the appliance
• Prevents water, steam, and air leaks that can cause poor performance or messes
• Helps maintain consistent internal temperature for efficient operation
• Reduces cycling and energy waste caused by a damaged or worn seal

• One replacement gasket

• Disconnect power and empty the appliance before starting any repair
• Inspect the door frame and mounting channel for damage or debris before installing
• Install by seating gasket evenly into the channel or following the OEM mounting clips/adhesive method

This door gasket creates a tight seal around the refrigerator door to help maintain consistent internal temperature and reduce energy use. Replacing a worn or torn gasket restores door sealing and helps prevent frost buildup. What it does:

• Seals the refrigerator door edge to keep cold air in and warm air out
• Helps prevent frost and ice buildup in the fresh food or freezer compartment
• Common symptom: visible cracks, tears, or a gap causing warm food or temperature fluctuation
• Common symptom: condensation or frost along the door seal or inner cabinet

• Turn off power to the appliance and empty the door area before starting
• Remove the old gasket carefully; inspect and clean the gasket channel and mating surface before installing
• Press the new gasket into the channel evenly; ensure magnets seat fully for a consistent seal

The Refrigerator Front Leg Seal Cover is an essential component designed to maintain the stability and efficiency of your Samsung refrigerator. This genuine OEM part ensures a perfect fit, replacing the original seal cover with ease and restoring your appliance to optimal condition. Crafted from durable materials, the seal cover effectively protects the front legs of your refrigerator from dirt, moisture, and everyday wear, extending the lifespan of your appliance. Its precise design not only enhances the overall appearance of your refrigerator but also contributes to better energy efficiency by ensuring a tight seal. Installing the Refrigerator Front Leg Seal Cover is simple and straightforward, allowing you to quickly address any damage or wear without the need for professional assistance. Compatible with a wide range of Samsung refrigerator models, this seal cover provides reliable performance and peace of mind. Enhance the functionality and look of your refrigerator with this high-quality, genuine OEM part, ensuring your appliance remains sturdy and efficient for years to come.

The Refrigerator Door Gasket Seal is essential for maintaining the efficiency of your Samsung refrigerator. This high-quality genuine OEM part ensures a tight and secure seal around the door, preventing unwanted air leaks. By effectively keeping cold air inside, it helps maintain the optimal temperature, which not only preserves your food longer but also enhances the refrigerator's energy efficiency. Crafted from durable rubber, this gasket seal is built to withstand daily use and resist wear and tear, providing long-lasting performance. Replacing a worn or damaged seal with the Refrigerator Door Gasket Seal can improve the overall functionality of your appliance, reducing energy costs and preventing ice build-up. This genuine OEM part is specifically designed to fit a variety of Samsung refrigerator models, ensuring a perfect fit and easy installation. Investing in this quality seal helps restore your refrigerator's performance, offering peace of mind and extending the lifespan of your appliance.

This door gasket assembly seals the perimeter of the refrigerator door to keep cold air in and moisture out. Replacing a worn gasket restores a tight seal, helps maintain proper temperatures, and reduces frost and condensation.

• Creates an airtight seal between the door and cabinet to prevent warm air infiltration
• Helps stabilize internal temperature and humidity for consistent cooling
• Reduces frost or condensation around the door opening
• Replace if the gasket is torn, warped, cracked, hardened, or not sealing; symptoms may include moisture, frost at the liner, or warmer-than-normal temps

• Disconnect power to the refrigerator before servicing
• Remove the old gasket from the door channel; some models require loosening retainer screws—do not overtighten on reassembly
• Warm the new gasket (soak in warm water or use a hair dryer on low) to relax folds before installation
• Seat corners first, press the gasket fully into the channel, then check for a continuous seal and adjust with gentle heat as needed

This refrigerator door gasket forms an airtight seal between the door and cabinet to keep cold air in and humid air out, helping restore stable temperatures and efficiency when the original seal is worn, torn, or warped.

• Seals the door perimeter to prevent air leaks and temperature swings
• Helps reduce frost and condensation around the door opening
• Can resolve doors not closing fully or popping back open
• Replace if the gasket is cracked, deformed, or won't stay seated

• Disconnect power and clear items from the door before starting
• Warm the new gasket (hot water or low heat) to relax folds and improve fit
• Pull the old gasket from the retaining channel; press the new one in firmly, starting at the corners
• Close the door and check for an even seal all around; allow the gasket to conform over the next 24 hours

Door gasket assembly forms the airtight seal around a refrigerator or freezer door to keep cold air in and moisture out. Replacing a worn or damaged gasket restores proper sealing and helps prevent frost and leaks. What it does:

• Seals the door perimeter to maintain internal temperature and reduce warm-air intrusion.
• Prevents moisture and condensation that can lead to frost buildup and water pooling.
• Common symptoms: visible cracks or tears in the gasket, gaps when the door is closed, excess frost or higher-than-normal interior temperature.
• Helps the appliance run more efficiently by restoring an effective door seal.

• Disconnect power to the appliance before starting any repair.
• Clean and dry the gasket seating surface before installing the new gasket.
• Press the gasket evenly into the door channel, starting at the corners and working around the perimeter.
• Check for uniform contact around the full seal after installation; adjust door alignment if necessary.

This door gasket assembly seals the refrigerator door to the cabinet, keeping cold air in and humid room air out. Replace a torn or deformed gasket to restore a tight seal, stable temperatures, and reduce frost or condensation.

• Creates an airtight seal around the door perimeter
• Helps maintain proper temperatures and consistent cooling
• Reduces warm-air leaks that lead to frost or condensation
• Common symptoms: torn/warped gasket, visible gaps, door not closing flush, or temperature swings

• Disconnect power before servicing
• Let the new gasket warm to room temperature; use warm water or gentle low heat to relax folds—do not overheat
• Remove the old gasket and press the new gasket fully into the door channel, ensuring corners seat properly
• Close the door and check contact all around; work the gasket as needed until it seals evenly

Color: White

This refrigerator door gasket seals the fresh-food compartment to help maintain proper cooling and reduce energy loss. It restores a tight door seal to help keep food fresher and the refrigerator running efficiently. What it does:

• Replaces a worn, torn, or deformed door seal to stop cold air leakage
• Helps maintain consistent internal temperature and reduce frost buildup
• Reduces strain on the compressor caused by a poor door seal
• Addresses symptoms like warm spots near the door, excessive frosting, or higher energy use

• One refrigerator door gasket

• Remove power to the appliance before replacing the gasket
• Clean the door flange and allow it to dry before installing the new gasket
• Work around the full perimeter, easing the gasket into the channel; avoid forcing or trimming unless OEM instructions specify
• If the gasket is stiff, warm it gently (per OEM guidance) to aid fitting; avoid open flames or excessive heat

This is the rear crisper seal that fits along the back edge of the refrigerator crisper compartment to help maintain the crisper enclosure and reduce air leakage. It restores a tighter seal for better humidity control and food storage. What it does:

• Replaces a worn or torn rear crisper gasket to help reduce cold air loss from the crisper area
• Helps maintain crisper humidity so produce stays fresher longer
• Prevents gaps that can cause uneven cooling or frost build-up near the drawer
• Can reduce draft noise or rubbing caused by a damaged seal

• One rear crisper seal (matches OEM part number)

• Remove the crisper drawer to access the rear seal before replacing
• Peel out the old seal and press the new seal firmly into the gasket channel; ensure an even, continuous fit
• Avoid using sharp tools that could damage the cabinet or new seal
• Unplug the refrigerator or switch off power if needed for safe access to nearby components