Kenmore / Sears Refrigerator Ice Maker & Related

The Icemaker is an OEM part for Whirlpool refrigerators. This component is responsible for producing ice by automatically filling with water, freezing it, and then ejecting the ice cubes into the storage bin. Please note that for installation, you will need to reuse the original cover and bracket from your existing icemaker. Makes 5 cubes at a time.

Causes of a bad icemaker can include mechanical failures, clogged water lines, or electrical issues. Over time, wear and tear from constant use or exposure to hard water and impurities can also affect its performance.

Symptoms of a bad icemaker include:

• The icemaker not producing ice
• Ice cubes being smaller than usual or misshapen
• Leaking water inside the freezer
• Unusual noises during the ice-making process
• The ice bin not filling up

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This ice container deflector attaches to the ice bucket assembly and guides cubes toward the dispenser chute. Replacing a cracked or missing deflector restores proper ice flow and helps keep ice from spilling inside the freezer during dispensing.

• Directs ice from the bucket into the dispenser chute/crusher path
• Helps maintain consistent dispensing and minimizes stray ice inside the freezer
• Replace if cracked, warped, or missing
• Symptoms include erratic dispensing, ice spilling or jamming, or a visibly damaged/missing guide on the ice bin

• Disconnect power before servicing; remove the ice bucket
• Position the new deflector in the original location; reuse existing screws/clips if applicable
• Ensure the curved face points toward the dispenser chute
• Reinstall the ice bucket, restore power, and test ice dispense

This Arm-Stripper is the factory replacement stripper arm that restores the original part that guides and supports related moving components, helping the appliance operate smoothly and quietly. What it does

• Positions and guides the component it mates with to prevent binding or misalignment.
• Helps maintain proper contact/clearance between moving parts for reliable operation.
• Prevents rubbing or wear that can cause noise or uneven performance.
• Common signs it may be needed: rubbing or scraping noises, part misalignment, or erratic movement where the arm is located.

• One Arm-Stripper replacement part.

• Recommended for users familiar with basic appliance repair; verify power is disconnected before starting.
• Inspect surrounding clips, fasteners and mating parts; replace damaged hardware as needed.
• Handle carefully to avoid bending or damaging the arm during installation.

Used to prevent over ice production in the ice dispensing bucket.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

This ejector arm replaces the dispenser ejector that helps move detergent or rinse aid from the dispenser to the wash chamber for proper release during the cycle. Restores reliable dispensing and prevents missed or partial releases. What it does:

• Physically pushes or guides detergent/rinse into the wash chamber at the correct point in the cycle
• Replaces cracked, broken, or worn ejector arms that fail to move or sit correctly
• Addresses symptoms such as detergent not dispensing, dispenser door sticking, or visible damage to the ejector arm
• Works with the dispenser assembly to ensure consistent product release during operation

• Disconnect power to the appliance before starting any repair
• Remove the dispenser assembly per the service manual to access and replace the ejector arm
• Inspect surrounding dispenser components (hinges, springs, clips) and replace if damaged

This Arm-Stripper is the OEM replacement component that holds and positions the stripper mechanism, restoring correct movement and alignment so the appliance operates smoothly and reliably. What it does:

• Replaces a worn or broken stripper arm that can cause misalignment or improper operation
• Restores correct part movement to reduce binding, noise, or skipped cycles
• Helps maintain proper engagement with adjacent components for consistent performance
• Fits into the existing mounting points and works with the original mechanism design

• One Arm-Stripper

• Disconnect power (unplug or shut off breaker) before beginning any repair
• Basic hand tools are usually required; handle the part and surrounding components carefully to avoid damage
• Inspect adjacent components (fasteners, clips, pivots) and replace if worn to ensure proper fit

This Arm Ejector secures and positions the dishwasher spray arm so it spins properly and distributes water for effective cleaning. Replacing a worn or broken ejector restores spray-arm stability and helps prevent uneven washing. What it does:

• Holds the spray arm in the correct position so it can rotate freely
• Prevents spray arm wobble, scraping, or falling off during cycles
• Helps maintain proper water distribution for consistent cleaning
• Can resolve symptoms like noisy spray arm movement or uneven wash performance

• Disconnect power and turn off the water supply before starting any repair
• Remove the lower spray arm and mounting cup as shown in your model's parts diagram to access the ejector
• Inspect surrounding components for wear when replacing the ejector
• Use only the exact replacement part number to ensure proper fit and function

The Icemaker Assembly is an OEM part for LG refrigerators. It is responsible for producing and storing ice within the freezer compartment.

You should replace the icemaker assembly if it becomes faulty. Causes of a bad icemaker assembly can include wear and tear from regular use, mineral buildup from hard water, or failures in the mechanical or electronic components. These issues can lead to inconsistent ice production or complete failure to produce ice.

Symptoms of a bad icemaker assembly include:

• The icemaker not producing ice
• Leaking water around the icemaker
• Ice cubes that are misshapen or smaller than usual
• Unusual noises coming from the icemaker

This OEM LG part is also compatible with Sears/Kenmore.