Kenmore / Sears Refrigerator Drawer, Shelf, Pan

This refrigerator pan trim finishes the front edge of the shelf/pan assembly and helps secure the glass above the drawers. Replacing a cracked or missing trim restores a clean look and proper support for everyday use.

• Attaches to the shelf or pan frame to create a finished front edge
• Helps retain and support the glass insert above the drawers
• Can improve drawer alignment when the original trim is cracked or loose
• Common symptoms: broken/cracked trim, loose or missing edge piece, glass not sitting flat

• Disconnect power and remove food items before servicing
• Slide the shelf assembly out and carefully lift out the glass
• Release locking tabs on the old trim; align and snap the new trim into place
• Reinstall the glass and shelf; verify smooth drawer operation

This pantry drawer is the clear utility bin in the fresh food section that stores deli items and snacks. Replace a cracked or missing drawer to restore smooth sliding access and organized, contained storage. What it does:

• Provides a dedicated compartment for meats, cheeses, produce, and snacks
• Slides on existing rails for easy access to contents
• Helps contain small spills to protect shelves below
• Common symptoms: cracked bin, broken tabs, drawer falls off tracks or sticks, missing drawer

• 1 pantry drawer bin

• Empty the existing drawer, lift slightly, and pull straight out to remove from the rails
• Inspect and clean rails/cover area; remove debris before installing
• Align the new bin with the tracks and slide in until fully seated—do not force
• Hand-wash with mild soap before use; avoid harsh abrasives

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Restore tidy storage in your refrigerator's deli/pantry drawer with this Pantry Drawer Divider. Replacing a cracked or missing divider keeps foods separated and helps the drawer slide and close properly without contents shifting or tipping.

• Separates and stabilizes items within the deli/pantry drawer for better organization
• Helps prevent contents from sliding and causing the drawer to bind
• Restores proper fit when the original divider is cracked, warped, or missing
• Typical symptoms: divider falls out or won't stay positioned; difficulty keeping foods organized

• Disconnect power to the refrigerator and remove items from the deli/pantry drawer
• Fully extend and lift out the drawer as directed in your user manual
• Align the divider with the molded slots/grooves and press or slide into place until secure
• Reinstall the drawer and verify smooth operation; do not force parts

This right-hand support is a small interior bracket used in select refrigerators to secure and stabilize the matching component on the right side. Replacing a cracked or missing support helps keep shelves and covers level and in place.

• Provides right-side support and alignment for the associated interior component
• Helps keep shelves/covers stable; prevents wobble, sagging, or unexpected drop
• Common signs of failure: broken tabs, cracked plastic, loose fit, or a missing support
• Replace if damaged from impact, overloading, or age

• Unplug the refrigerator and remove items to access the area
• Remove the related shelf/cover and retain any screws or clips
• Transfer and reuse the original mounting hardware if required
• Align the new support in the same orientation; secure firmly and confirm level before reassembly

The Snack Pan is an OEM part for Whirlpool refrigerators. It provides a designated space for storing snacks and small items within your refrigerator.

A bad snack pan can be caused by regular use, accidental damage, or exposure to spills and stains. If you notice cracks, discoloration, or a broken structure in the snack pan, it may indicate a problem with the pan itself.

Symptoms of a bad snack pan include:

• Cracked or damaged pan surface
• Discoloration or staining of the pan
• Inability to open or close the drawer

Replace your faulty snack pan with this genuine OEM part to restore your refrigerator. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Utility Pan is an OEM part for Whirlpool refrigerators. It is a storage drawer for various items in your refrigerator, such as deli meats, cheeses, and other small food items.

A bad utility drawer pan can be caused by regular use, accidental damage, or wear and tear over time. If you notice cracks, breaks, or warping in the pan, it may be time to replace it.

Symptoms of a bad utility drawer pan include:

• Cracks or breaks in the pan
• Warping or misalignment of the pan
• Difficulty in opening or closing the drawer

Replace your damaged or worn-out utility drawer pan with this genuine OEM part to restore your refrigerator. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Pan Cover Glass Insert is an OEM part for Frigidaire refrigerators. It acts as the shelf above the crisper drawers, providing a stable and transparent surface for storing fruits, vegetables, and other perishables. This glass insert is crucial for maintaining the organization within the fridge, allowing for easy visibility and access to items stored in the crisper drawers beneath it. 

Causes of damage to the Pan Cover Glass Insert can include overloading it with too heavy items, accidental impacts during the loading or unloading of groceries, or sudden temperature changes that can cause glass to weaken or crack.

Symptoms indicating the need for a replacement include:

• Visible cracks or chips in the glass
• Scratches that impair visibility
• Shattering of the glass insert

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Shelf - "Spill-Safe" is an OEM part for Frigidaire refrigerators. This shelf is designed to contain spills and prevent liquids from leaking onto other shelves or the bottom of the refrigerator, helping to maintain cleanliness and order within the appliance.

Over time, heavy loads, accidental impacts, or temperature fluctuations can cause the shelf to weaken or break.

Symptoms of a bad shelf include:

• Visible cracks or breaks in the shelf
• Liquids leaking through the shelf
• Difficulty in fitting the shelf securely in place
• The shelf not supporting weight properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Tray Asm is an OEM part for LG refrigerators. It is designed to store fruits and vegetables at optimal humidity levels, helping to keep produce fresh for longer periods. It has approximate measurements of 30 inches in length, 18 inches in width, and 4 inches in height.

Causes of a bad tray asm can include cracking or breaking due to frequent use, accidental dropping, or exposure to heavy loads that exceed its capacity. Over time, the plastic can also become brittle and more susceptible to damage.

Symptoms of a bad tray asm include:

• Cracks or breaks in the drawer
• Difficulty sliding the drawer in and out
• Produce not staying fresh as long
• The drawer not fitting properly in its compartment

This OEM LG part is also compatible with Sears/Kenmore models.

The Crisper Pan is an OEM part for Whirlpool refrigerators. It provides a dedicated space for storing fruits and vegetables, helping to maintain their freshness by regulating humidity levels within the drawer. The pan measures approximately 16 3/8" Wide X 15" Deep X 8 1/4" High.

You should replace this crisper pan if it becomes cracked or damaged. Causes of a bad crisper pan can include impact from dropping or overloading, wear and tear from frequent use, or damage from cleaning with harsh chemicals.

Symptoms of a bad crisper pan include:

• Cracks or holes in the pan
• Difficulty sliding the pan in and out of the refrigerator
• Food items not staying fresh as long

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drawer Cover Frame is an OEM replacement part for Frigidaire refrigerators. This component is specifically designed to house the shelf glass and hold the refrigerator drawer in place.

Causes for a malfunctioning Drawer Cover Frame can include physical damage from overloading, wear and tear from frequent use, or structural issues that affect its ability to securely hold the shelf glass and drawer.

Symptoms of a bad Drawer Cover Frame include:

• The shelf glass not being securely housed, leading to instability
• The refrigerator drawer is not being held firmly, causing misalignment or sliding issues
• Visible cracks or damage to the frame affecting its structural integrity
• Difficulty in accessing or securing the refrigerator drawer due to frame issues

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This left-hand support secures and aligns the corresponding shelf or drawer assembly inside the refrigerator, helping it sit level and operate smoothly. Replace a cracked or missing support to restore proper fit and function.

• Provides structural support on the left side of the mounted assembly
• Maintains level alignment to prevent binding, rubbing, or sagging
• Helps drawers/shelves open and close smoothly when intact
• Common signs: uneven or sticking operation, tilting or dropping, visible cracks or broken tabs

• Disconnect power and remove items from the affected area before servicing
• Remove the shelf/drawer; release locking tabs or remove any fasteners holding the old support
• Position the new support on the left side and reuse existing hardware if required
• Smooth operation before reloading

The Shelf Support is an OEM part for Frigidaire refrigerators. Installed at set positions along the side walls, shelf supports provide sturdy surfaces on which to rest adjustable shelves or glass shelves. 

Causes of bad shelf supports can include general wear from repeated loading and unloading of shelves over time, as well as damage from accidental impacts.

Symptoms of bad shelf supports include:

• Shelves that wobble or sag in positions
• Difficulty inserting or removing shelves
• Small dents or breaks in the support surfaces
• Supports that are loosened from wall positions

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Shelf Support is an OEM part for Frigidaire refrigerators. This part provides stability and support for refrigerator shelves, ensuring that they remain securely in place and can hold the weight of stored items.

Causes of a bad shelf support can include accidental impacts, overloading the shelves with heavy items, or wear and tear over time. 

Symptoms of a bad shelf support include:

• Shelves that do not stay securely in place
• Sagging or tilting shelves
• Cracks or visible damage on the supports
• Difficulty in adjusting or repositioning shelves

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.