Kenmore / Sears Wall Oven Heating Element

This ceiling-mounted broil element delivers the intense, top-down radiant heat your oven needs for broiling and finishing. Replacing a failed element restores strong, even broiler performance and consistent browning. What it does:

• Provides high-temperature, top-down heat for broiling, searing, and finishing foods
• Common symptoms of failure: broiler won't heat, uneven broiling, or element does not glow
• Visible cracks, blistering, or breaks on the element indicate it's burned out
• Restores normal broil operation when the original element is open/failed

• 1 broil element

• Disconnect power at the breaker and allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and disconnect the two wire terminals; support wires so they don't slip back into the cavity
• Reconnect terminals firmly, secure the element, and ensure it's clear of oven walls
• Test the broil function before returning the appliance to service

The Surface Element is an OEM replacement part for Frigidaire electric ranges, designed to provide efficient and even heating for cooking on the stovetop. This component is a radiant surface element commonly seen on glass and ceramic cooktops. 8 inch, 2200 watt

Causes of a faulty Surface Element can be due to overuse causing burnout, physical damage like cracks from heavy cookware, electrical issues such as faulty wiring, and corrosion disrupting heating.

Symptoms of a bad Surface Element include:

• Not heating up, indicating it may be burnt out or disconnected.
• Heating irregularly or only partially, suggesting there might be damage to the element.
• Taking longer than usual to heat up, which could point to electrical issues or reduced efficiency due to wear and tear.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This electric broil element mounts at the top of the oven cavity to deliver direct radiant heat for broiling and finishing. Replacing a failed element restores strong, even top heat so foods brown properly and Broil works as designed.

• Supplies top-of-oven radiant heat during the Broil cycle for searing and browning
• Replaces a burned-out or cracked element that no longer heats
• Common symptoms: no heat in Broil, weak/uneven top browning, visible breaks or blistering, or tripping the breaker when Broil is selected

• Turn off power at the breaker and allow the oven to cool completely before service
• Remove oven racks; take out the element's mounting screws, gently pull the element forward, and disconnect the two spade terminals—support wires so they don't retract into the insulation
• Transfer any mounting hardware from the old element if needed; reconnect terminals fully, secure the element, restore power, and test Broil
• Inspect terminals/wiring for heat damage and replace compromised connectors before reassembly

The Broil Heating Element is an OEM part for Frigidaire ranges. Located inside the oven compartment, it provides heat energy for the broil cooking function. 

Causes of a bad broil element can include mineral buildup over time, surface corrosion or internal wire fatigue from ongoing temperature cycling.

Symptoms of a bad broil element include:

• Inadequate or uneven broiling temperatures
• Element failing to glow red or turn on fully
• Burning or charring of foods below the element
• Oven display showing error code related to element failure

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Restore reliable heat to your electric range or cooktop with this surface heating element. Replacing a failed top-burner element brings back consistent, even heating so pots and pans heat up properly at your chosen setting.

• Supplies electric heat to a cooktop burner zone when turned on
• Common fix for a burner that won't heat or only partially glows/heats
• Helps address uneven or slow heating on the affected element
• Replace if the element shows visible breaks, blisters, or has shorted

• Disconnect power at the breaker and allow the cooktop to cool completely before service
• Access varies by model; support and protect glass tops when lifting/removing
• Photograph wiring; transfer any original brackets, insulators, or limiter/thermostat if present
• Ensure clean, tight terminal connections; fully reassemble before restoring power

This bake element heats the oven cavity for standard baking operations, restoring even heat when the original element fails. It installs at the rear or bottom of the oven cavity to provide the radiant heat needed for baking. What it does:

• Heats the oven cavity to maintain proper baking temperatures.
• Replaces a burned, broken, or visibly damaged element that won't glow or heat.
• Helps correct symptoms like insufficient heat, uneven baking, or an oven that won't reach set temperature.
• Works with the oven's control system and thermostat to deliver steady radiant heat.

• Disconnect power to the appliance before starting — turn off the circuit breaker or unplug the range.
• Allow the oven and old element to fully cool before handling.
• Handle the element carefully to avoid bending or damaging the terminals or ceramic insulators.
• After installation, restore power and test the oven on a bake cycle to ensure the element heats correctly.

This surface heating element powers one of your range's top burners, restoring steady, responsive heat for everyday cooking. Replace a failed element to bring your cooktop back to consistent performance when boiling, simmering, or sautéing.

• Provides heat to the selected surface burner when the control is turned on
• Works with the burner switch to reach and maintain set temperatures
• Common symptoms of failure: burner won't heat, heats unevenly or intermittently, or shows visible damage/hot spots
• Helps resolve long heat-up times and inconsistent cooking results

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing.
• Access and mounting vary by model; note wire locations and transfer any brackets/clips from the original element.
• Inspect terminals and connectors; replace any heat-damaged wiring or receptacles before reconnecting.
• Handle by the frame and avoid stressing the element; ensure secure electrical connections before testing.

This electric heating element restores consistent, reliable heat in your appliance, so cooking or warming functions work as intended. Replace a failed element to eliminate slow heat-up, uneven temperatures, or no-heat conditions.

• Converts electrical power into heat for the appliance's designated cavity or surface
• Common failure symptoms: no heat, uneven heating, very slow preheat/warm-up
• Visual clues: breaks, blisters, or hot spots on the coil
• May cause the unit to cycle erratically or trip a breaker if shorted

• Disconnect power at the breaker or unplug before servicing; allow all components to cool
• Wear cut-resistant gloves; avoid bending or kinking the element
• Photograph wiring and transfer connectors one-for-one; ensure tight, clean terminal fits
• Inspect wires/terminals for heat damage and replace any compromised connectors

This oven bake element generates the heat for the Bake cycle. Replace it when the oven won't heat or takes too long to reach temperature to help restore consistent, even baking performance.

• Provides primary heat during the Bake mode
• Common symptoms of failure: no heat in Bake, very slow preheat, uneven or undercooked results
• Element shows visible damage such as blisters, breaks, or burned spots
• Replacing a failed element can restore normal oven operation

• Disconnect power at the breaker; ovens use high voltage
• Remove oven racks and access the element from the oven cavity; note screw locations and wiring
• Move wires to the new element one at a time and ensure snug terminal connections
• Avoid bending the element or overtightening screws; restore power and test Bake

This broil element mounts at the top of the oven cavity and delivers radiant heat for broiling and top-browning. Replace a broken or burned-out element to restore consistent broil performance.

• Emits high, radiant heat from the top of the oven during the broil cycle
• Used to sear and top-brown foods
• Replaces the original broil element on compatible units
• Common symptoms: No heat in broil, element won't glow, uneven top browning, visible cracks/blistering on the element

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; support the element while removing mounting screws
• Carefully pull the element forward and disconnect the wire terminals; avoid bending the element
• Attach the new element, secure with screws, ensure it is clear of the oven liner, then restore power and test

The Broil Element is an OEM part for Whirlpool wall ovens and ranges. This heating element is responsible for the broiling function of the oven.

Located at the top of the oven cavity, the broil element functions by directing intense radiant heat downward to cook and brown food from above. 

Causes may include natural wear and damage over prolonged high-heat use. Electrical malfunctions inside the element can also cause premature failure. 

Symptoms of a bad broil element include:

• Failure of the broil function
• Diminished or uneven heating during broil cycles
• The presence of cracks, breaks or corrosion on the heating coils

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Broil Element is an OEM part for Whirlpool ranges. This heating element is responsible for providing high heat from the top of the oven, essential for broiling and achieving a crisp, browned finish on dishes.

Common causes of a faulty broil element include wear and tear over time, exposure to high temperatures, or physical damage from cleaning or moving oven racks.

Symptoms of a bad broil element include:

• The broil element not heating up
• Uneven cooking or broiling results
• Visible damage, such as breaks or blisters on the element
• The oven not reaching the desired temperature during broiling

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement surface element restores proper heating on an electric range or cooktop's top burner. When the original element is open, weak, or damaged, it helps the selected cooking zone reach temperature and heat more evenly.

• Converts electrical power into heat at the chosen surface zone for everyday cooking
• Replaces an element that is open, shorted, or physically damaged
• Common symptoms: surface burner won't heat, heats intermittently, heats very slowly, or shows uneven temperatures
• Works with existing controls to maintain set heat levels

• Disconnect power at the breaker or unplug the appliance; allow the cooktop to cool completely
• Access the element per your model's service procedure (often by lifting the top or accessing from beneath the cooktop)
• Transfer wires one at a time to the matching terminals; secure the element and any brackets as originally installed
• Inspect connectors/wiring for heat damage and address as needed before restoring power and testing

The surface element is an OEM part for Whirlpool electric ranges. It is responsible for generating heat through its electric coils or elements on the cooktop. 

Causes of a bad surface element can include wear and tear over time, cracks or damage to the electric coils from heat stress or impact, or failure of the underlying electric components.

Symptoms of a bad surface element include:

• Slow or uneven heating of the cooktop surface
• Hot or cold spots when cooking  
• Elements failing to glow red when turned on
• Burned or charred pans and cookware
• Tripped breakers or blown fuses 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, and some Kenmore electric ranges and cooktops.

This bake element supplies the primary heat from the bottom of the oven during the Bake cycle. Replace it to restore proper preheating and even results when the original is burned out, damaged, or no longer heating. What it does:

• Provides radiant heat for baking and preheating from the lower oven position
• Helps the oven reach and maintain the set temperature for consistent cooking
• Common symptoms: no heat in Bake, very slow preheating, uneven baking, or a visible blister/crack in the element
• Restores normal oven operation when the existing element has failed

• 1 bake element

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward
• Support and disconnect the two wire terminals; prevent wires from slipping back into the insulation
• Attach wires to the new element, secure with existing hardware, restore power, and test

The Surface Element is an OEM part for Frigidaire electric ranges. As the key heating component on the cooktop, the surface element produces heat through resistance when electrical current flows through it.

Causes can be normal wear over time exposed to heat cycles, damaged or degraded internal components, corrosion of terminals or wires, or surface damage from improper cleaning.

Symptoms of a bad surface element include:

• Slow or uneven heating
• Burning or scorching of cookware easily
• Element that will not heat at all or only reaches low temperatures
• Frayed, cracked, or broken wiring at the element terminal

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.