Kenmore / Sears Washer Tub Ring Or Cover, Counterweight

This washer balance weight mounts to the outer tub to absorb vibration and stabilize the drum during spin. Replacing a damaged or missing weight helps restore smoother, quieter operation and reduces movement caused by unbalanced loads. What it does:

• Adds mass to the outer tub to counterbalance spinning loads
• Helps reduce vibration, banging, and "walking" during spin
• Supports proper spin speed and cycle completion
• Replaces a cracked, crumbling, or loose tub weight

• 1 balance weight

• Disconnect power and water supply before servicing
• Access the weight by removing the necessary panels
• Support the tub and hold the weight while removing/installing bolts; tighten evenly in a crisscross pattern
• Reuse existing mounting hardware and ensure all weights and mounting points are intact before testing

The balancer assembly mounts to the washer's basket/tub to counterbalance loads during spin. When worn or damaged, it can cause shaking, banging, or out-of-balance errors. Replacing it helps restore smoother, quieter spin performance.

• Stabilizes the basket/tub during acceleration and high-speed spin
• Helps reduce vibration, banging, and washer "walking"
• Can prevent spin cycles from slowing or stopping due to imbalance

• Disconnect power and allow moving parts to stop before servicing
• Access is typically at the top of the tub/basket under the tub ring; remove covers as needed
• Note orientation; seat the assembly evenly and ensure all tabs/fasteners are fully engaged
• After reassembly, run an empty spin test to verify smooth operation

This tub cover forms the front half of the washer's outer tub. It seals the tub and provides the mounting lip for the door boot, helping prevent leaks and keeping the spin basket properly aligned with the cabinet opening.

• Seals the front of the outer tub and provides a secure seat for the door boot/bellows
• Contains wash water during all cycles to prevent leaks and splashing
• Maintains proper clearance for the spin basket to avoid contact with the front opening
• Common failure symptoms include leaks at the front or bottom of the cabinet, visible cracks/warping, or the door boot repeatedly coming loose or tearing

• Disconnect power and water; wear gloves and protect sharp edges
• Remove top and front panels; release the outer boot clamp and peel the door boot from the front panel. Detach any hoses/wiring from the cover, remove the perimeter bolts, and transfer any fittings from the old cover
• Clean sealing surfaces; inspect/replace the tub-to-cover gasket if your model uses a separate one. Seat the new cover and tighten fasteners evenly in a crisscross pattern
• Reinstall the boot and clamp carefully, reassemble the cabinet, and run a fill/spin test to check for leaks

This balance weight is the washer drum counterweight that helps stabilize the tub during spin cycles to reduce vibration and excessive movement. It restores smoother, quieter operation when the drum is unbalanced. What it does:

• Counters the rotating drum to reduce vibration, shaking and banging during spin
• Helps maintain drum alignment for consistent spin performance
• Reduces noise caused by an imbalanced load or worn/loose weight
• Prevents excessive movement that can stress suspension components

• Disconnect power and water supply before starting any repair
• Support the tub/outer cabinet to prevent it from shifting when removing old weight
• Retain and reuse original fasteners only if in good condition; replace damaged hardware

A balance weight that helps stabilize the washer tub during spin cycles to reduce vibration and prevent the appliance from rocking. Replaces a worn or broken cabinet weight to restore smoother, quieter operation. What it does:

• Adds mass to the washer cabinet to counteract tub imbalance during spins
• Reduces excessive vibration, shaking, and loud banging noises when spinning
• Helps prevent the washer from walking or shifting on the floor
• Works as the factory replacement for the original cabinet balance assembly

• Disconnect power and, if applicable, water supply before starting any repair
• Empty the drum and remove the required access panels per your model's service manual
• Securely fasten the weight using the original mounting hardware and torque per OEM guidance

For seal only use part number 131901400.

This tub cover replaces the outer trim that surrounds the washer tub to protect internal components and provide a finished appearance. It restores a snug seal and helps keep water and debris away from moving parts. What it does:

• Covers and protects the outer edge of the washer tub to reduce debris intrusion and wear
• Helps maintain proper alignment and spacing between the tub and cabinet trim
• Restores the washer's finished appearance if the original cover is cracked, warped, or missing
• Can reduce noise caused by loose or damaged tub trim contacting other components

• One replacement tub cover

• Basic hand tools may be required; disconnect power and water before beginning
• Inspect surrounding seals and fasteners; replace any damaged clips or screws for a secure fit
• Handle carefully to avoid scratching the finish during installation

Washer tub ring that snaps onto the top of the outer tub. It acts as the tub cover and splash guard, guiding water back into the tub and supporting inlet or dispenser fittings to help keep the rim area contained.

• Attaches to the top of the outer tub as the upper splash guard/tub cover
• Directs water back into the tub; supports inlet/dispenser nozzles, if equipped
• Maintains proper clearance around the spin basket
• Common replacement signs: cracks, broken locking tabs, splashing from the rim, or rubbing at the top opening

What's included: 1 tub ring Install notes:

• Disconnect power and water supplies before servicing
• Lift or remove the top panel to access the tub rim
• Release locking tabs and detach any hoses/nozzles from the old ring; transfer fittings if needed
• Seat the new ring evenly; ensure all tabs fully engage. Reassemble and run a test cycle to check for leaks/splashing

This replacement counterweight helps balance and stabilize a refrigerator or freezer door so it opens and closes smoothly and stays properly aligned. It restores correct door movement and reduces sag that can interfere with sealing or latching. What it does:

• Balances the appliance door to prevent drooping and uneven closing
• Helps the door stay open or closed as designed for safer access
• Reduces stress on hinges and latch mechanisms from misaligned doors
• Can eliminate symptoms like a sagging door, difficulty latching, or uneven gaps

What's included: One counterweight. Install notes:

• Disconnect power to the appliance before starting any work.
• Support the door securely while removing/installing the counterweight to avoid injury or damage.
• Installation may require basic hand tools and removal of trim or hinge hardware; follow the OEM service instructions for your model.
• After installation, check door alignment and latch engagement; adjust hinge hardware per manufacturer guidance if needed.