Kenmore / Sears Washer Clip Or Clamp

If you have an older model WM8000H_A you MUST pay attention to the type of door gasket (boot seal) that it uses. Every video I could find for replacing the seal on the WM8000HWA involved a different product than what was required for our specific washer. I wound up getting the wrong one by ordering it without help and had to exchange it - after I had the machine taken apart. Thanks to AppliancePartsPros I got the correct seal and front retaining ring the next day. NOTE! The retaining rings are... Read more

The repair was fairly straight foward as shown in the video. However, driving the shaft from the bearings took some doing. It required replacing the use of the board with a spare bolt and a 2lb hand sledge. (having an air hammer as reserve, also not a bad idea) I rated this reair as a "1" however I've been an auto mechanic for 40 years. If you do not have good general mechanical ablities you may find this more challenging as you get it further apart. I suggest anyone making this repair should... Read more

• Spins slowly
• Will not agitate
• Pumps but will not spin

My parents have the older 80 series washer and dryer that gets used way more than a consumer washer and dryer was ever meant to be used. The washing machine finally said im tired. During the spin cycle it was making a really loud squealing noise and during the agitation cycle it would barely agitate the clothes. So i ordered the basket drive to get rid of the squealing during spin cycle and noticed the dogs on the cams were warn and werent grabbing so ordered the whole cam kit to be safe... Read more

The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more

Replaced all three dampers and then replaced locking gaskets for the top spring mounts for the drum, replaced the old feet pads I had and works like a charm! Read more

Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks. Door sensor... Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly. Timer... In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering... Read more

I started by watching the video and it was very helpful. I would make one suggestion. On our model the weights on the tub sit very close to the front gasket. It is much easier to put the gasket on the tub before you put the weights on. Also, since the washer was tore apart, I replaced the hoses and seals and shocks since the machine is about 8 years old. The shocks made a huge difference. It spins like it did when it was new. Thanks for the video, it was very helpful. Read more

New hose and clamp. Read more

I went to your web site found the part using the model number of the washer machine. Also with the part picture, there was a video showing step by step instructions. They were very clear and was breeze replacing the hose.Doing this myself saved at least probably $150-200. Appliance repair shops quoted me around $80.00 just to come out. Then they mark up the price of the hose at least twice the cost of what I paid , They too have to order the part and come back to install. So the labor was what... Read more