Kenmore / Sears Washer Control Board

The Noise Filter Assembly is an OEM part for LG washing machines, designed to minimize electrical noise interference within the appliance. This essential component ensures that the washer operates smoothly without emitting disruptive sounds that can affect both the performance of the washer and the comfort of your home environment. 

Causes of a bad Noise Filter Assembly can range from wear and tear over time to exposure to power surges or electrical spikes, which can damage the internal components of the filter. 

Symptoms of a bad Noise Filter Assembly include:

• Increased electrical noise or buzzing sounds emanating from the washer
• Intermittent disruptions in the washer's performance
• The washing machine failing to start or experiencing power fluctuations

This OEM LG part is also compatible with some Kenmore models.

The Control Timer is an OEM replacement part specific to Whirlpool washers. It is the electronic component responsible for governing the sequence and duration of wash cycles. Located inside the control console, the timer works with the control dial to initiate various wash/rinse phases based on the selected settings.

Causes for timer failure may include water exposure corroding electrical circuits or repeated rapid switching wearing out internal switches.

Symptoms of a faulty control timer include:

• Inability to advance through complete cycles
• Random operation of rinse or spin functions
• Premature termination of cycles before finishing
• Failure to respond when turning the cycle selector

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a motor control board for a washing machine. It comes with the board, tape, bracket, and screw mounted on control. In most cases, this part is located on the bottom of the appliance near the drive motor. The purpose is to control the speed of the drive motor. It also works to determine the direction of the tumble and spin actions while a cycle is in process. If the washing machine is pumping but does not spin, this is often the result of a malfunctioning motor control board.If the motor control board has gone bad, it should be replaced. To replace it, make sure the washer is unplugged or the circuit breaker has been turned off. Pull the washer away from the wall, remove the knobs from the front and screws from the back, and lift the control panel. This offers access to the motor control board, which should be removed so the new part can be installed.This motor control board is made for use with washing machines by Electrolux, Frigidaire, Crosley, and Kenmore. It is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.

The Timer is an OEM part for Whirlpool washing machines. This part controls the various cycles of the washing machine, including wash, rinse, and spin cycles, by regulating the amount of time each cycle runs.

Causes of a bad timer can include electrical malfunctions, wear and tear over time, or damage to the timer's internal mechanisms.

Symptoms of a bad timer include:

• The washer not advancing through cycles
• Cycles running too long or too short
• The washer stopping mid-cycle
• Inconsistent or unpredictable cycle timing

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This mechanical timer sequences the dishwasher through its wash, drain, and dry steps. Replacing a failing timer restores proper cycle advancement so the dishwasher starts, progresses, and finishes cycles reliably. What it does:

• Times and sequences power to the wash motor, drain pump, fill valve, and heater for each stage of the cycle
• Advances the cycle automatically and moves the dial/indicator through programmed steps
• Coordinates wash, rinse, and dry durations for consistent results
• Typical failure symptoms: cycle won't advance or stops mid-cycle; runs too long; must be advanced manually; timer knob won't turn

• 1 mechanical timer assembly

• Disconnect power at the breaker before servicing; do not rely on the control panel to turn the unit off
• Access the timer from the control console/inner door; remove screws to reach the component
• Photograph/label wire positions and transfer leads to the new timer one at a time
• Reuse existing mounting hardware and knob; ensure the shaft orientation matches before reassembly

This mechanical cycle timer controls the sequence and duration of operations in the selected program. Replacing a worn timer restores reliable cycle selection and proper advancing from start to finish.

• Controls cycle timing and advancement via internal cams and contacts
• Directs power to components in the correct order for each cycle
• Stops the appliance at the end of the cycle
• Fixes: cycle won't advance or gets stuck, won't start, stops mid-cycle, dial doesn't move or skips

• Disconnect power before servicing
• Access the timer through the control console; remove knob/dial as needed
• Transfer wires one at a time from the old timer to the new unit, matching terminals
• Reuse existing mounting hardware and console parts; verify proper alignment before reassembly

This motor control board is created for use with washing machines. It's located inside the washing machine, where users can change settings and start or stop the appliance. It is tasked with regulating how quickly the washer spins during a cycle. Wear and tear or damage can cause the motor control board to malfunction. This may make it impossible for the washer to agitate or spin. If this happens, a replacement will need to be made.To replace this part, start by unplugging the appliance. Once the area is safe, the bottom front panel should be removed. This will provide access to the original motor control board. Pull on the motor control board until the wires can be reached. The position of these components should be noted before taking out the part. Replace with a new motor control board and replace the wires.This motor control board is designed to fit washing machines made by Maytag, Whirlpool, Kenmore, and KitchenAid. This is an authentic OEM replacement part that is sourced directly from the manufacturer. It's sold as a single part.

This electronic control board manages the appliance's core operations by interpreting inputs and switching power to components. Replacing a failed board restores proper control of cycles and functions when the unit is unresponsive or behaving erratically.

• Coordinates cycle timing and operation based on signals from sensors and the user interface
• Switches power to loads via onboard relays/triacs
• Monitors for faults and stores/displays error codes for diagnostics
• Failure symptoms can include: won't start, no response at controls, cycle won't advance, intermittent operation, or recurring error codes

• Disconnect power before servicing; follow all safety and ESD precautions
• Photograph/label connectors; transfer wiring one at a time to the new board and secure with existing hardware
• Restore power and perform any model-specific diagnostics, resets, or calibrations per the tech sheet/service manual

This is a Whirlpool drive motor control board, or MCU, for washing machines. It monitors and controls the speed and direction of the drive motor. If this board fails, the washer likey will not work, and the display may show an error code like F70.Before installing this part, be sure to cut power to the appliance and allow it to drain, cool, and dry completely. The washer will need to be pulled away from any walls to properly access the control panel. After opening the panel, remove any mounting screws or wire harnesses connecting the old drive motor control board and install the new one in its place.This is a genuine OEM part compatible with washers manufactured by Whirlpool brands, including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product contains no additional parts or hardware.

This timer is the appliance's cycle controller. It routes power to the right components in a programmed sequence and advances the cycle at the correct intervals, restoring proper progression and reliable start/stop of functions when the original fails.

• Advances the machine through each step and duration selected
• Opens and closes internal contacts to power motors, heaters, and valves as designed
• Interfaces with the control knob/shaft for user-selected settings
• Common symptoms: cycle won't advance, timer doesn't move, stuck mid-cycle, or runs indefinitely

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Note wire locations and transfer one wire at a time to the matching terminals on the new timer
• Reuse existing mounting hardware and control knob/shaft parts as applicable
• After installation, run a short test cycle to confirm the timer advances correctly

This motor control board regulates and powers the washer's drive motor, coordinating speed, direction, and spin. Replacing a failed module can restore proper tumbling/spinning performance and resolve common motor-related faults.

• Supplies variable-speed power to the drive motor for wash and spin
• Monitors motor feedback to maintain correct speed and direction
• Communicates with the main control to carry out cycle commands
• Common symptoms: no tumble or spin, erratic/incomplete spin, cycle stops with motor/communication errors

• Disconnect power before servicing; verify power is off
• Use ESD protection and handle the board by the edges
• Access the board inside the cabinet; move connectors one at a time and seat them fully
• Inspect the motor and wiring harness for shorts or damage before restoring power

This noise filter assembly conditions incoming AC power to reduce electromagnetic interference before it reaches the control system. A failed line filter can cause no power, intermittent shutdowns, or breaker trips; replacing restores stable, reliable operation. What it does:

• Filters EMI/RFI on the power line to help protect sensitive control electronics
• Helps prevent interference that can cause no power, flickering display, or random resets
• A failing filter may trip a breaker/GFCI when the unit is plugged in or starts a cycle
• Visual clues can include scorch marks, burnt odor, or a cracked/bulged filter body

• 1 noise filter assembly

• Disconnect power before servicing; verify the outlet is de-energized
• Access is typically near the power cord entry behind a rear/top panel (varies by model)
• Label or photograph wire positions and transfer connections one by one; secure the ground
• Mount firmly and route wires to avoid pinching; reassemble and test for proper operation

• Line filter, EMI filter, RFI filter

The Coin Slide Interface is an OEM part for Whirlpool commercial washers. It is a component that allows users to insert coins or tokens to activate the machine and initiate the laundry cycle.

Causes of a faulty coin slide interface can include regular wear and tear, damage due to misuse or vandalism, or electrical component failure. These factors can result in issues such as coin rejection, incorrect coin counting, or the inability to start the machine using coins.

Symptoms of a Bad Part:

• Will not start
• Not washing properly
• Timer will not set

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This OEM replacement part is a control board for washers. The control board is the main computer that sends signals to the washer to perform its essential functions. If the washer is no longer turning on, spinning, rinsing or draining properly, this could mean that the control board needs to be replaced. Luckily this is a relatively simple repair. To begin, start by shutting off all power to the appliance. Proceed to move the washer away from the wall to gain access to the upper back panel. Remove the upper back panel and locate the old control board. Pull it out of its mounted position and take note of the orientation of the wires attached to the old board. Reinsert the wire harness and individual wire into their correct terminals on the new board. Snap the board back into place and reinstall the upper back panel. This genuine replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

The Timer is an OEM part for Whirlpool washing machines. This component is responsible for controlling the various cycles of the washing machine, ensuring that each phase, from washing to rinsing to spinning, occurs at the correct time and duration.

Causes of a bad timer can include electrical faults, wear and tear on the internal mechanisms, or damage due to power surges or moisture exposure. Over time, these issues can interfere with the timer's ability to accurately manage the washing cycles, leading to performance problems.

Symptoms of a bad timer include:

• The washing machine not advancing through cycles
• Incorrect cycle durations
• The machine getting stuck in one part of the cycle
• Unresponsive or erratic timer controls

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Restore accurate cycle control with this washer timer. It sequences power to the drive motor, pump, and water inlet valves so the machine fills, washes, drains, and spins at the proper times.

• Advances the cycle through fill, wash, rinse, drain, and spin stages
• Sends power to the motor, pump, and inlet valves in the correct order and duration
• Safe symptoms: washer won't start, won't advance, stops mid-cycle, runs indefinitely, or skips rinse/spin
• Helps when cycles stall or the dial turns without moving the cycle forward

• Unplug the washer before servicing
• Open the control console to access the timer; note or photograph wiring
• Transfer wires one at a time to matching terminals on the new timer
• Reuse your existing knob/dial and mounting hardware; align the timer shaft before tightening