Kitchenaid Dishwasher Parts

This positioner aligns and secures its mating component in the correct location inside your appliance. Replacing a cracked, worn, or missing positioner restores proper fit so the assembly stays put and operates as designed.

• Holds the related part in the proper position and orientation
• Prevents shifting, sagging, or rattling during use
• Supports smooth adjustment or movement where applicable
• Common symptoms: loose or misaligned component, difficulty adjusting or seating the piece, visible cracks, or a missing clip

• Disconnect power; also shut off gas or water if your appliance uses these utilities
• Note the original orientation and take photos before removal
• Transfer any reused hardware and fully seat tabs/slots to avoid damage
• Wear cut-resistant gloves and check alignment after reassembly

Color: White. Size: 13 oz. Spray paint primer. can.

This Barrier protects and separates appliance components, keeping wiring and parts properly aligned for reliable operation. It's a simple, durable replacement that restores the original spacing and support inside the appliance. What it does:

• Provides a stable mounting/separation surface to prevent rubbing or contact between parts
• Helps maintain correct component alignment to reduce vibration and noise
• Prevents wiring or small parts from contacting hot or moving components
• Common symptom: visible cracks, breaks, or shifted parts where components no longer sit securely

• One barrier as shown

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove any panels or covers that block access; keep track of fasteners
• This part typically installs with screws or snap-fit tabs—do not force components

This cover is a factory replacement access panel that protects internal components and restores the appliance's finished appearance. It keeps wiring and controls shielded from dust and accidental contact for safer, longer-lasting operation. What it does:

• Shields internal wiring, controls, and components from dust, debris and accidental contact
• Keeps small parts and fasteners secured inside the appliance cabinet
• Restores the appliance's finished exterior where the original cover was damaged or missing
• Helps maintain proper airflow routing and component spacing when installed correctly

• Disconnect power to the appliance before beginning any service to avoid shock or injury.
• Verify the cover orientation and fastener locations before securing; use OEM screws where specified.
• Handle with care to avoid scratching or bending the cover; ensure tabs snap fully into place.
• Inspect for damage and secure any loose parts before installing the cover.

The Tine Clip is an OEM part specifically designed for Whirlpool brand dishwashers. This small but important piece secures individual tines to the upper dish rack for stability during washing.

Repeated use causes plastic clips to become brittle or dislodge over time from heavy loads. This jeopardizes proper rack assembly and performance. 

Causes of a bad tine clip could be normal wear and tear, damaged pads from sharp dishes, or improper loading of heavily soiled cookware.

Symptoms of a failing tine clip include:

• Loosened or detaching dishrack tines that shift positions 
• Gaps allowing collected food and particles to fall through
• Reduced support for delicate or small dishes in affected areas

This OEM Whirlpool replacement restores the rack's fully functional design. Compatible with Maytag, KitchenAid, Jenn-Air, and other models, it improves washing coverage and optimizes usable space.
 

This is a genuine replacement screw used to secure appliance components. It provides a simple, reliable fastener for reattaching panels, brackets, or assemblies so parts stay properly mounted and stable during operation. What it does

• Secures panels, trim, brackets or small assemblies in place
• Restores proper fastening where a missing or damaged screw causes loose parts or rattling
• Prevents movement that can lead to noise or misalignment of adjacent components
• Used wherever the original screw was removed or lost during repairs

• One replacement screw

• Use the matching screw head and thread engagement; do not force if it does not seat smoothly
• Tighten until snug—avoid overtightening to prevent stripping or cracking plastic parts
• Disconnect power before working on electrical appliances and follow basic safety precautions
• If original screw was rusted, check mating threads for damage before installing new fastener

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

This thermostat bracket holds the oven or range thermostat securely in place, ensuring accurate temperature sensing and stable oven performance. Replaces a worn or broken bracket to restore proper thermostat positioning. What it does:

• Secures the thermostat assembly to the oven/range interior so the thermostat bulb or probe senses temperature correctly
• Prevents the thermostat from shifting or contacting heating elements
• Commonly replaced when the bracket is cracked, bent, or missing and causes temperature or control issues
• Helps reduce temperature inconsistencies caused by a loose or damaged mounting

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Handle the thermostat and sensor bulb carefully; avoid kinks or direct pressure on sensing elements
• Basic hand tools are typically required; verify part alignment before tightening fasteners

This mount is a support bracket designed to secure internal components and reduce movement for a stable, quiet operation. It replaces worn or broken mounts to restore proper alignment and prevent rattling. What it does

• Supports and stabilizes internal parts to reduce vibration and noise
• Keeps components aligned to prevent uneven wear
• Helps stop rattling or clunking caused by a loose or damaged mount
• Used when a visible break, crack, or missing mounting point is present

• One mount/support bracket

• Disconnect power to the appliance before starting any repair
• Inspect surrounding parts and mounting hardware; replace damaged fasteners as needed
• Use proper tools and avoid over-tightening fasteners to prevent cracking the mount

Color: Bisque

This screw fastener secures appliance panels and components to keep assemblies stable during normal use. A simple replacement for damaged or missing screws that restore proper fit and reduce rattling. What it does:

• Holds appliance panels, brackets, or trim in place to prevent movement
• Helps stop vibrations and rattling caused by loose hardware
• Replaces stripped or corroded screws that no longer tighten properly
• Restores a flush, secure fit where a matching screw is required

• One screw as shown

• Disconnect power and follow safety procedures before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping the screw head
• Seat the screw straight and tighten until snug; do not overtighten to avoid damaging parts
• Keep removed hardware organized to ensure correct reassembly

This is the pump and motor assembly that is used on under counter dishwasher units. The function of this part is to pump the water through the spray arms during the dishwashing cycle. If the user notices that the dishes and cookware are not getting clean, it could be because the pump or motor is not working correctly. If the pump and motor assembly are faulty, the user may also notice water pooling at the bottom of the dishwasher. It may also make a whining sound, which indicates that the motor is dying. Disconnect the dishwasher from the electrical outlet before replacing this part or shut off the house circuit breaker for the dishwasher. Wear work gloves for safety during the process.This part is sold individually. It comes straight from the manufacturer. This particular pump and motor assembly are compatible with dishwashers that are manufactured by Whirlpool and KitchenAid.

This chrome handle medallion restores the finished look of a damaged or worn appliance handle by replacing the decorative cover. It improves appearance and helps protect the underlying handle hardware from wear. What it does:

• Replaces a scratched, dented, or faded handle trim piece to renew the appliance's appearance
• Covers and protects the handle mounting area from everyday wear
• Matches chrome finishes for a consistent, factory look
• Helps eliminate cosmetic blemishes that make the appliance look older

• Basic hand tools are typically required; follow the appliance's user manual or parts diagram for correct removal/replacement of the handle
• Remove the handle or access panel carefully to avoid scratching adjacent finishes
• Keep hardware and fasteners organized during disassembly so original parts can be reused

This replacement door handle restores a secure grip and smooth opening for compatible Whirlpool appliances. It replaces worn, cracked or broken handles to improve usability and appearance without replacing the whole door. What it does

• Provides a sturdy handhold to open and close the appliance door
• Replaces cracked, loose or cosmetically damaged handles
• Helps prevent accidental drops or slippage when opening the door
• Matches the original mounting points for a direct-fit replacement

• Remove power and empty the door area before starting any repairs
• Use common hand tools; hold parts steady to avoid scratching finishes
• Follow OEM instructions for fastener torque and alignment

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification