Kitchenaid Dishwasher Parts

Replacement door spring for dishwashers. Restores proper tension to prevent door from dropping or falling when opened. Install to replace broken, worn, or weak springs.

Cooktop burners not heating? A blown thermal fuse cuts power to prevent overheating. Test for continuity and replace to restore heating function.

Water line kit for connecting ice makers to household water supply. Includes copper tubing, valve, and fittings for installation under kitchen sink.

Fix a dishwasher that won't drain or makes loud grinding noises. This drain pump and motor assembly removes standing water during cycles. Moderate DIY.

Replacement dishwasher housing assembly that encloses internal components and aligns panels. Use to replace cracked, warped, or damaged housings.

Touch-up paint for repairing chipped, scratched, or rusted dishwasher racks. Brush-on formula restores appearance where coating is worn or missing.

Touch-up paint for restoring chips, scratches, and nicks on painted appliance surfaces. Covers minor cosmetic damage on exterior panels and finishes.

Replacement track assembly for dishwasher upper rack. Mounts to dishwasher tub side wall. Includes left and right tracks with bearings and stops.

This electronic control board manages the dishwasher's settings and cycle operations, restoring responsive touch controls and reliable cycle sequencing so dishes are cleaned on the selected program. Replaces a failed or unresponsive console control module. What it does:

• Interprets user inputs and runs the dishwasher's programmed cycles.
• Controls timing, wash/dry functions, and interface feedback.
• Common symptom: touchpad or display unresponsive or erratic behavior.
• Common symptom: cycles fail to start, stop mid-cycle, or show error codes tied to control faults.

• One electronic control board (W10757829).

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Handle the board by edges to avoid ESD damage; use anti-static precautions if available.
• Some models require removing the control panel or inner door trim to access the board.

Dishrack adjuster assembly for dishwashers. Mounts to upper rack and slides along track rails. Replace if wheels are broken, housing is cracked, or worn.

Adjustable leveling leg that supports and stabilizes your dishwasher under counters. Replace if cracked, stripped, or unable to hold level position.

Rear wheel support that guides and stabilizes the dishwasher rack as it slides. Replace if cracked, broken, or worn to restore smooth gliding motion.

Fix standing water in your dishwasher tub with this drain pump motor assembly. Solves drainage failures and grinding noises. Moderate DIY repair.

The Tine Clip is an OEM part specifically designed for Whirlpool brand dishwashers. This small but important piece secures individual tines to the upper dish rack for stability during washing.

Repeated use causes plastic clips to become brittle or dislodge over time from heavy loads. This jeopardizes proper rack assembly and performance. 

Causes of a bad tine clip could be normal wear and tear, damaged pads from sharp dishes, or improper loading of heavily soiled cookware.

Symptoms of a failing tine clip include:

• Loosened or detaching dishrack tines that shift positions 
• Gaps allowing collected food and particles to fall through
• Reduced support for delicate or small dishes in affected areas

This OEM Whirlpool replacement restores the rack's fully functional design. Compatible with Maytag, KitchenAid, Jenn-Air, and other models, it improves washing coverage and optimizes usable space.
 

This adjustable manifold is a direct-fit replacement that secures and positions the appliance's manifold assembly so related components line up and function correctly. It restores proper alignment and reliable operation when the original is bent or worn. What it does:

• Provides a mounting surface and adjustable position for the manifold assembly and attached components
• Helps maintain correct alignment so burners/valves operate smoothly
• Restores fit when the original manifold is damaged, bent, or loose
• Resolves symptoms such as uneven burner operation, ignition difficulty, or mechanical misalignment

• Turn off power and shut off gas supply before starting work
• Handle and align carefully to avoid bending; secure with the OEM fasteners
• Check seals and connections after installation; test operation per manufacturer instructions

Color: White. Size: 13 oz. Spray paint primer. can.