Kitchenaid Refrigerator Gasket & Seal

Replacement gasket that restores a watertight seal at the factory connection to help prevent leaks and protect floors and cabinetry from water damage. Use to replace cracked, hardened, or torn seals. What it does:

• Seals mating surfaces to stop water leakage and reduce moisture-related damage.
• Common symptoms it helps address: visible leaks, pooled water under the appliance, or degraded/rubbery gasket material.
• Replaces worn, cracked, stiff, or torn seals to restore proper sealing performance.
• Seats into the original gasket groove—ensure the seal is fully seated with no gaps.

• Disconnect power and water supply before starting any service.
• Remove the old gasket, then clean and dry the mating surfaces and gasket groove.
• Press the new gasket into the groove evenly and inspect for full engagement around the perimeter.
• Restore power/water and run a short test cycle; check thoroughly for leaks before returning the appliance to regular use.

This rear icebox gasket seals the freezer/icebox compartment to help maintain proper temperature and reduce frost buildup. It restores the door seal so the appliance runs more efficiently and prevents moisture intrusion. What it does:

• Seals the icebox/freezer compartment to keep cold air in and warm, humid air out
• Helps prevent frost and ice buildup inside the icebox
• Reduces temperature fluctuations that can cause food spoilage
• Can stop condensation or water pooling caused by a failing door seal

• Unplug the appliance before attempting replacement
• Remove the old gasket fully and clean the mounting channel before installing the new seal
• Press the new gasket into the channel evenly; allow time for the gasket to form to the door

The Door Gasket is an OEM part for Whirlpool refrigerators. It creates an essential seal around the refrigerator door, helping to maintain cool interior temperatures and energy efficiency.

Causes of a bad door gasket can include cracks, tears, or compressions from repeated closing of the door over many years of use. Exposure to heat or sharp objects may also damage the sealing material.  

Symptoms of a bad door gasket include: 

• Ineffective sealing allowing warm air into the refrigerator 
• Increased cooling requirement from the compressor to maintain temperatures
• Frost or moisture buildup around the door seal
• Gaps are visible along the door frame where the gasket makes contact

Color: Grey 

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The door gasket is an OEM part for Whirlpool refrigerators. It forms a seal between the refrigerator door and body, working to ensure peak cooling and energy efficiency. This rubber gasket acts as insulation, preventing warm air from entering the refrigerator compartment each time the door is opened.

Causes of a bad door gasket can include cracks, tears, or compression from repeatedly opening and closing the refrigerator door over an extended period of time.

Symptoms of a bad door gasket include:

• Inefficient cooling and higher energy costs
• Warm air leaking into the refrigerator
• Moisture buildup or frost inside the body
• Difficulty properly sealing the door shut

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This refrigerator door gasket forms an airtight seal between the door and cabinet. Replacing a worn seal helps stop warm air leaks, reduce frost and condensation, and keep temperatures stable for better efficiency and food preservation.

• Creates a continuous perimeter seal between the door and cabinet to prevent air infiltration
• Helps maintain correct temperatures and reduce moisture/frost buildup
• Restores proper door closing when the old gasket is torn, warped, or permanently compressed
• Common symptoms: door not sealing or popping open, condensation around the door, temperature swings, frost along the door edges

What's included: 1 door gasket Installation notes:

• Disconnect power before servicing
• Let the new gasket relax at room temperature or warm it in water to remove kinks
• Pull the old gasket from the door channel; clean the mating surface
• Seat corners first, then press the gasket fully into the channel; use gentle low heat to smooth waves if needed

The Door Gasket is an OEM part for Whirlpool refrigerators. It forms an insulating perimeter around the refrigerator door opening to maintain cool interior temperatures during use.

Causes relate to the breakdown of sealing materials from repeated compression cycles over many years. Cracks or loose areas compromise the barrier.

Symptoms of a defective door gasket can include:

• Warm air entering around the door edges
• Interior humidity increases causing frost or condensation
• Higher electric bills from lost cooling efficiency
• Inability to maintain set temperatures over long periods

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Color - Grey

Color: Grey

This replacement gasket seals the appliance door to help maintain proper temperature and prevent leaks, keeping the interior efficient and protected. Use it to restore a tight door seal and reduce energy loss from gaps. What it does:

• Forms a secure seal around the door to keep heat or cold inside the appliance
• Prevents water, steam, and air leaks that can cause poor performance or messes
• Helps maintain consistent internal temperature for efficient operation
• Reduces cycling and energy waste caused by a damaged or worn seal

• One replacement gasket

• Disconnect power and empty the appliance before starting any repair
• Inspect the door frame and mounting channel for damage or debris before installing
• Install by seating gasket evenly into the channel or following the OEM mounting clips/adhesive method

The Freezer Door Gasket is an OEM replacement part for Whirlpool bottom-mount refrigerators. This white freezer door gasket is responsible for maintaining a tight air seal around the entrance to the freezing compartment. It helps retain cold air inside and prevents warm drafts or humidity from affecting food freshness and freezer efficiency. 

Symptoms of a bad freezer gasket include: 

• Difficulty keeping consistent temperatures inside the freezer section
• Visible moisture, frost, or condensation around the door perimeter
• Noticeable warm air infiltration reducing cooling performance

Causes of freezer gasket failure involve regular opening and closing of the door. Over time, the flexible material breaks down from continuous use exposing it to changing environmental temperatures. Physical damage from overstuffing shelves or slamming the door can also prematurely damage the gasket.

This OEM replacement is also compatible with some KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

This gasket seals the FIP assembly to prevent air and moisture leaks, helping maintain proper temperature and efficiency. A worn or damaged seal can lead to condensation, frost buildup, or temperature fluctuations.

• Creates an airtight seal at the FIP interface to keep air and moisture out
• Helps reduce frost/ice accumulation and condensation around the assembly
• Can address issues like warm spots, frequent cycling, or visible gaps at the seal
• Restores proper sealing performance when the original gasket is cracked, flattened, or torn

• Disconnect power before servicing; wear cut-resistant gloves
• Remove cover/fasteners to access the FIP sealing surface
• Clean mating surfaces; install gasket evenly without stretching
• Verify even seating and recheck for pinches or gaps before reassembly

Replace a worn or torn refrigerator door gasket to restore a tight seal and help maintain proper cooling. This exact-service door gasket in Apollo Gray fits the door edge and compresses to keep cold air in and warm air out. What it does:

• Seals the refrigerator/freezer door to help maintain internal temperature and energy efficiency.
• Prevents warm, humid air from entering and forming frost or condensation inside the compartment.
• Helps eliminate drafty edges, clicking door behavior, and uneven cooling near the door.
• Restores proper door closure when the original gasket is cracked, flattened, or damaged.

• High-level replacement: remove the old gasket, align the new gasket in the door channel, and press into place; follow factory warm-water or heat-stretch procedures if required by the OEM.
• Inspect the door flange and mounting channel for damage or debris before installing the new gasket.
• For best seal, allow gasket to settle for 24 hours and check for gaps; use care when heating or stretching to avoid distortion.
• Disconnect power only if instructed by the appliance manufacturer for your specific model.