Lg Tub Ring Or Cover, Counterweight

This washer balance weight mounts to the outer tub to absorb vibration and stabilize the drum during spin. Replacing a damaged or missing weight helps restore smoother, quieter operation and reduces movement caused by unbalanced loads. What it does:

• Adds mass to the outer tub to counterbalance spinning loads
• Helps reduce vibration, banging, and "walking" during spin
• Supports proper spin speed and cycle completion
• Replaces a cracked, crumbling, or loose tub weight

• 1 balance weight

• Disconnect power and water supply before servicing
• Access the weight by removing the necessary panels
• Support the tub and hold the weight while removing/installing bolts; tighten evenly in a crisscross pattern
• Reuse existing mounting hardware and ensure all weights and mounting points are intact before testing

This tub cover forms the front half of the washer's outer tub. It seals the tub and provides the mounting lip for the door boot, helping prevent leaks and keeping the spin basket properly aligned with the cabinet opening.

• Seals the front of the outer tub and provides a secure seat for the door boot/bellows
• Contains wash water during all cycles to prevent leaks and splashing
• Maintains proper clearance for the spin basket to avoid contact with the front opening
• Common failure symptoms include leaks at the front or bottom of the cabinet, visible cracks/warping, or the door boot repeatedly coming loose or tearing

• Disconnect power and water; wear gloves and protect sharp edges
• Remove top and front panels; release the outer boot clamp and peel the door boot from the front panel. Detach any hoses/wiring from the cover, remove the perimeter bolts, and transfer any fittings from the old cover
• Clean sealing surfaces; inspect/replace the tub-to-cover gasket if your model uses a separate one. Seat the new cover and tighten fasteners evenly in a crisscross pattern
• Reinstall the boot and clamp carefully, reassemble the cabinet, and run a fill/spin test to check for leaks

This balance weight is the washer drum counterweight that helps stabilize the tub during spin cycles to reduce vibration and excessive movement. It restores smoother, quieter operation when the drum is unbalanced. What it does:

• Counters the rotating drum to reduce vibration, shaking and banging during spin
• Helps maintain drum alignment for consistent spin performance
• Reduces noise caused by an imbalanced load or worn/loose weight
• Prevents excessive movement that can stress suspension components

• Disconnect power and water supply before starting any repair
• Support the tub/outer cabinet to prevent it from shifting when removing old weight
• Retain and reuse original fasteners only if in good condition; replace damaged hardware

A balance weight that helps stabilize the washer tub during spin cycles to reduce vibration and prevent the appliance from rocking. Replaces a worn or broken cabinet weight to restore smoother, quieter operation. What it does:

• Adds mass to the washer cabinet to counteract tub imbalance during spins
• Reduces excessive vibration, shaking, and loud banging noises when spinning
• Helps prevent the washer from walking or shifting on the floor
• Works as the factory replacement for the original cabinet balance assembly

• Disconnect power and, if applicable, water supply before starting any repair
• Empty the drum and remove the required access panels per your model's service manual
• Securely fasten the weight using the original mounting hardware and torque per OEM guidance

This replacement balance weight helps stabilize the washer tub during spin cycles to reduce excessive shaking and banging. Restores proper weight distribution so the washer runs more quietly and completes cycles without heavy vibration. What it does:

• Adds counterweight to the washer tub to help balance loads during spin.
• Reduces shaking, banging, and excessive movement during high-speed spins.
• Can help prevent intermittent off-balance conditions and noisy operation.
• Works as a direct replacement for worn, cracked, or missing tub weights.

• Disconnect power and turn off water supply before beginning any repairs.
• Access may require removing the washer cabinet or front panel; follow the model-specific service manual.
• Wear gloves and eye protection; use appropriate tools and fasteners to secure the weight.

This balance weight stabilizes the washer drum to reduce vibration and keep the washer steady during spin cycles. Replacing a worn or damaged weight restores smoother operation and reduces shaking and noise. What it does:

• Adds mass to the washer frame/drum assembly so the tub stays balanced during spin
• Helps prevent excessive vibration, banging, and movement during high-speed spins
• Reduces noise caused by an unbalanced load or damaged weight
• Supports proper drum alignment to avoid premature wear on bearings and suspension parts

• One balance weight

• Always unplug the washer before starting any repair to avoid electrical shock
• Support the drum/tub when removing or installing the weight to prevent component damage
• Reuse or replace any mounting hardware only if explicitly specified by the manufacturer
• If vibration persists after replacement, inspect suspension, shock absorbers, and mounting points

This balance weight assembly replaces the factory counterweight that helps keep the appliance door properly balanced for smooth opening and closing. Restores correct door alignment and reduces sag or uneven closing. What it does:

• Counterbalances the door to maintain proper alignment and even gaps
• Helps the door stay open at intended angles and reduces unexpected slamming
• Reduces strain on hinges and related hardware that can cause premature wear
• Commonly used when door sag, uneven closing, or misalignment is observed

• Disconnect power (and water, if applicable) before beginning service
• Follow the appliance service manual for correct removal of the door or trim to access the weight
• Use appropriate hand tools and support the door to prevent dropping or injury