Lg Gasket & Seal

• Leaks water

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

I watched the video that was shown on this website to slide the top back, remove the control panel, remove the front panel of the washer, remove the old gasket (the two tension springs are easy to get off, not as easy to replace), cleaned out years of gunk and soap that had built up behind the gasket for 10 years as well as under the rollers in the drum (each roller has a screw, remove it, slide the roller assembly forward and lift up to take off the rollers, and the roller can be broken down... Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

I called an appliance repair company. They use a flat rate billing system which I don't like. They told me it will cost around $250.00 to replace the gasket and I would have to move my machine out so he would have room to repair it. He said the part would be in in 5 days. I found you on line, ordered the part for around $69.00 and to my delight there was a video on how the repairs should be done. The video was very professionally done and I watched it twice just to memorize the procedure. ... Read more

Ordered the gasket first from Sears, but they sent me the wrong part, i.e. on the drawing on their web site the part was right (ADX73550621 - Refrigerator Door Gasket, Left), but when I received it - it was too small and didn't fit. Returned it to Sears and tried to find it somewhere else. Fortunately found the part on this site. It was helpful that the part photo was taken with an inch grid in the background, so I could compare dimensions against the old piece. The dimensions matched (wanted... Read more

****** always make sure the unit is fully unplugged from the power before you do anything with the outside of the unit to work inside of the unit and while you are working inside the unit... Also make sure that you turn the hot and cold water intake valves off and make sure you don't pull too much on the two water intake hoses that lead to your washer because they can leak with too much pressure exerted on either end******* 1. Took top off unit by unscrewing mounting brackets at two similar... Read more

From reading "troubleshooting" sites on the internet, originally thought I'd be replacing the front & rear drum rollers, so I ordered the rollers, and a new belt before I opened up the dryer, taking it out of use. When I opened it up the front rollers were "shot", and the front bulkhead was "totaled". Waited for parts to arrive (within 2 days), and successfully replaced front & rear rollers, bulkhead, drum seal. The on-line videos really helped me ensure I was keeping in the right order. My... Read more

Replaced door gaskets with new ones Read more

The right door seal and the freezer door seal are easily removed and replaced. They just pull out of the slot. These 2 new gaskets push in easily. The left door has the French Door Mullion, that blocks the removal of the door gasket. There are two screws in the middle that holds it on, and there is a spring at the bottom of the mullion that keeps the mullion in place. The spring can easily be removed, or left in place. There is an electrical connector in the middle of the mullion. As suggested... Read more

If you have an older model WM8000H_A you MUST pay attention to the type of door gasket (boot seal) that it uses. Every video I could find for replacing the seal on the WM8000HWA involved a different product than what was required for our specific washer. I wound up getting the wrong one by ordering it without help and had to exchange it - after I had the machine taken apart. Thanks to AppliancePartsPros I got the correct seal and front retaining ring the next day. NOTE! The retaining rings are... Read more

LG Washing Machine WM3885HCCA I searched the Appliance Parts Pros "Get Repair Help" tab, typed in the LG washing machine model number (WM3885HCCA), watched videos and searched for the parts shown on the diagrams of my LG washing machine. After finding parts, I confirmed on both the Appliance Parts Pros site and LG site that the parts I selected were correct. I highly recommend using the LG site . I was able to type in the original part number from the Appliance Parts Pro site and LG directed... Read more

Initially did a uTube search for specific instructions on dismantling this machine for this repair. I had successfully replaced a door/tub gasket on a Whirlpool front load machine previously. Did not find specific uTube instructions for this Kenmore. So began removing parts using past learned info on what needed to be removed first, second, and last. Removed the top, detergent dispenser screws/control panel, then the front (with a couple hidden screws around drain pump filter) and the front... Read more

This filter just captured all the junk in the bottom of my LG dishwasher. There is no cleaning or servicing this thing. You need to replace it. There is NO NEED to pull out the dishwasher. All can be done through the door. Remove the racks. Remove the rotating arm on the bottom (2 screws under the arm). Remove the single screw (on the bottom) holding the tube that goes up the back of the washer. The tube has two clips that need to be spread apart to get the tube completely out of the... Read more

So we removed the old ones and replaced them with the new ones. The job was quite easy and took only minutes to complete. Read more

Ordered boot, nozzle, and inner spring for boot. Would have ordered outer, but the schematic for parts made it very difficult to navigate to locate parts...24 hr/next day air and I have a happy wife. The only thing that would have made it easier, was having a pair of Spring Expansion pliers, be careful not to pinch inner boot! Used Youtube video as a walk through, completed in the fraction of the time if i hadnt watched! Read more

Ordered and installed replacement seal Read more