Tub Ring Or Cover, Counterweight

Note: Newly designed cover includes 4 new rod and spring assemblies. The tub dampening straps and clips are no longer used.

This washer balance weight mounts to the outer tub to absorb vibration and stabilize the drum during spin. Replacing a damaged or missing weight helps restore smoother, quieter operation and reduces movement caused by unbalanced loads. What it does:

• Adds mass to the outer tub to counterbalance spinning loads
• Helps reduce vibration, banging, and "walking" during spin
• Supports proper spin speed and cycle completion
• Replaces a cracked, crumbling, or loose tub weight

• 1 balance weight

• Disconnect power and water supply before servicing
• Access the weight by removing the necessary panels
• Support the tub and hold the weight while removing/installing bolts; tighten evenly in a crisscross pattern
• Reuse existing mounting hardware and ensure all weights and mounting points are intact before testing

This tub ring mounts to the top of the washer's outer tub to act as a splash guard and cover. Replacing a cracked or loose ring helps contain wash water and helps prevent leaks or debris from the top. What it does:

• Forms the upper splash guard around the outer tub to keep water contained during wash and spin
• Serves as the top cover at the tub opening, locking in with tabs/clips
• Damage (cracks, broken tabs) may lead to leaks from the top, rattling, or a loose ring
• Visible wear can leave plastic fragments in the basket or around the tub opening

• 1 tub ring

• Disconnect power and turn off water supplies before servicing
• Lift or remove the top/console per model design to access the tub opening; support the lid
• Release the locking tabs/clips and remove the old ring; clean the tub lip
• Align and press the new ring evenly until all tabs fully engage; reassemble and test

The balancer assembly mounts to the washer's basket/tub to counterbalance loads during spin. When worn or damaged, it can cause shaking, banging, or out-of-balance errors. Replacing it helps restore smoother, quieter spin performance.

• Stabilizes the basket/tub during acceleration and high-speed spin
• Helps reduce vibration, banging, and washer "walking"
• Can prevent spin cycles from slowing or stopping due to imbalance

• Disconnect power and allow moving parts to stop before servicing
• Access is typically at the top of the tub/basket under the tub ring; remove covers as needed
• Note orientation; seat the assembly evenly and ensure all tabs/fasteners are fully engaged
• After reassembly, run an empty spin test to verify smooth operation

This tub cover and gasket seal the top of the outer tub to contain splashing and prevent leaks during wash and spin. Replacing a cracked cover or compressed gasket restores a tight rim seal and cleaner operation. What it does:

• Creates a watertight seal at the outer tub rim
• Helps reduce splash-over and directs incoming water flow
• Helps keep clothing and debris out of the gap between basket and outer tub
• Common symptoms: leaks from the top/front, visible cracks in the ring, or a brittle/torn gasket

• One tub cover and one perimeter gasket

• Disconnect power and turn off the water supply before servicing
• Access the tub area; release retaining clips/screws and detach any inlet/flume from the old cover
• Clean the tub rim thoroughly; seat the new gasket evenly and install the cover without pinching the seal
• Reuse existing fasteners/clips; ensure the cover is fully latched all around and do not overtighten

This tub cover forms the front half of the washer's outer tub. It seals the tub and provides the mounting lip for the door boot, helping prevent leaks and keeping the spin basket properly aligned with the cabinet opening.

• Seals the front of the outer tub and provides a secure seat for the door boot/bellows
• Contains wash water during all cycles to prevent leaks and splashing
• Maintains proper clearance for the spin basket to avoid contact with the front opening
• Common failure symptoms include leaks at the front or bottom of the cabinet, visible cracks/warping, or the door boot repeatedly coming loose or tearing

• Disconnect power and water; wear gloves and protect sharp edges
• Remove top and front panels; release the outer boot clamp and peel the door boot from the front panel. Detach any hoses/wiring from the cover, remove the perimeter bolts, and transfer any fittings from the old cover
• Clean sealing surfaces; inspect/replace the tub-to-cover gasket if your model uses a separate one. Seat the new cover and tighten fasteners evenly in a crisscross pattern
• Reinstall the boot and clamp carefully, reassemble the cabinet, and run a fill/spin test to check for leaks

Restore a proper seal at the top of your washer's tub with this tub cover assembly. It contains water and suds, reduces splashing, and provides a smooth rim to protect garments during wash and spin. Also called a tub ring.

• Seals the top of the outer tub to keep water and suds contained during operation
• Provides a smooth basket opening to help prevent fabric snagging
• Helps maintain stable operation; a cracked or loose cover can rub, vibrate, or leak
• Common symptoms: water or suds at the top of the tub, excessive splashing, visible cracks or broken tabs

• Disconnect power and turn off water supply before servicing
• Lift/remove the washer top to access the tub area; release clips/fasteners holding the old cover
• Clean the tub lip and transfer any reusable components from the old cover if applicable
• Seat the new cover evenly and secure all tabs/clamps; run a leak check

This rear counterweight helps restore proper balance to the appliance door or panel so it opens and closes smoothly and stays in position during use. It's a direct-fit replacement designed to match the original component. What it does:

• Balances the door/panel to reduce sagging and uneven movement
• Restores smooth opening and closing motion
• Helps stop unwanted rattling or shifting during operation
• Works with the original bracket and fasteners to maintain correct alignment

• Disconnect power (and water if applicable) before beginning service
• Support the door or panel while removing the old counterweight to prevent drop or injury
• Remove and reuse factory fasteners unless replacements are provided; tighten securely to OEM torque

This balance weight is the washer drum counterweight that helps stabilize the tub during spin cycles to reduce vibration and excessive movement. It restores smoother, quieter operation when the drum is unbalanced. What it does:

• Counters the rotating drum to reduce vibration, shaking and banging during spin
• Helps maintain drum alignment for consistent spin performance
• Reduces noise caused by an imbalanced load or worn/loose weight
• Prevents excessive movement that can stress suspension components

• Disconnect power and water supply before starting any repair
• Support the tub/outer cabinet to prevent it from shifting when removing old weight
• Retain and reuse original fasteners only if in good condition; replace damaged hardware

A balance weight that helps stabilize the washer tub during spin cycles to reduce vibration and prevent the appliance from rocking. Replaces a worn or broken cabinet weight to restore smoother, quieter operation. What it does:

• Adds mass to the washer cabinet to counteract tub imbalance during spins
• Reduces excessive vibration, shaking, and loud banging noises when spinning
• Helps prevent the washer from walking or shifting on the floor
• Works as the factory replacement for the original cabinet balance assembly

• Disconnect power and, if applicable, water supply before starting any repair
• Empty the drum and remove the required access panels per your model's service manual
• Securely fasten the weight using the original mounting hardware and torque per OEM guidance

For seal only use part number 131901400.

This tub cover replaces the outer trim that surrounds the washer tub to protect internal components and provide a finished appearance. It restores a snug seal and helps keep water and debris away from moving parts. What it does:

• Covers and protects the outer edge of the washer tub to reduce debris intrusion and wear
• Helps maintain proper alignment and spacing between the tub and cabinet trim
• Restores the washer's finished appearance if the original cover is cracked, warped, or missing
• Can reduce noise caused by loose or damaged tub trim contacting other components

• One replacement tub cover

• Basic hand tools may be required; disconnect power and water before beginning
• Inspect surrounding seals and fasteners; replace any damaged clips or screws for a secure fit
• Handle carefully to avoid scratching the finish during installation

This counterweight is a replacement door balance weight that helps stabilize an appliance door for smoother, more controlled opening and closing. It restores proper door balance and reduces sagging or uneven movement. What it does:

• Adds counterbalance weight to a refrigerator/freezer door assembly for correct alignment
• Helps prevent door sag, slamming, or uneven closing that can compromise the seal
• Reduces strain on hinges and ensures doors operate smoothly
• Quietly stabilizes the door during normal use

• One counterweight

• Disconnect power and empty/remove door contents before starting
• Follow the appliance service manual for door removal/installation; some steps may require two people
• Use appropriate hand tools and avoid forcing parts; retain fasteners for reuse