Magic Chef Cooktop Parts

It was very easy caled up ordered the part no prblem got it in 3 days.Got a phillips screw driver removed the top of the stove took out the old one a put in the new one had it fixed within minutes very easy diy no need to pay someone alot of money for this easy fix. Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

Purchased proper hinges. Lifted oven doors off the hinges. Removed screws securing the oven to the cabinet, then slid out the unit from the cabinet far enough to access the hinges. Then removed trim to better access the hinges. Then removed the screws holding the hinges. Then installed the new hinges, secured them with the screws, then reinstalled the trim, then slid the unit back into the cabinet, and secured it in place with the screws. Finally, I placed the oven doors back on my hinges. ... Read more

I first DISCONNECTED POWER FROM THE RANGE using the breaker. I then pulled the range out from the wall to give myself plenty of working room. I lifted the range top up as when you clean under the burners. I then moved the ends of the bottom of the slide rods that lock the range top open back where they came loose from the top of the range. This allows you to fold it higher and have complete access to the top of the range. I then took out all the Phillips head screws that hold down the sheet... Read more

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

• Won't start

I have a Jenn-Air microwave that didn't turn on and had no lights. It just stopped working completely. I unplugged the unit and had to remove the rear cover using a *security screw kit* that prevents people from opening the rear panel. Once opened, I removed the fuse and testing it with an OHM reader to determine that the fuse went bad. But I also had to determine why the fuse blew and noticed a sticky oily substance under the Capacitor. I used a rubber glove and needle nose pliers to... Read more

First and foremost I UNPLUGGED THE OVEN!. I'll pass on the early morning SHOCK THERAPY! Second, I unscrewed aluminum protection plate from back of oven. Next, I unplugged the two connections behind the oven switch. Then I removed the plastic switch from the front and unscrewed the two screws that secured the oven switch to the oven. Once you've completed all these steps you take your new oven switch and do everything again but in reverse order. Hope this was informative, direct, and that your... Read more

These are very easy to replace ,just gave the old one a quarter turn lifted it out took the two wires off (noted where each one will go on the new burner ) pop the wires onto the new burner put it on and good to go. Read more

• Door won't open or close

I replaced the hinge due to the hinge spring breaking. To replace the hinge you do the following: 1. Disconnect power to stove, either at circuit box or at outlet. 2. Lift door off of outside hinge arms ; no screws are used to attach the door to the hinge 3. Remove two screw on under side of cook top, one on each side. 4. Disconnect cook top connector. 5. Lift cook top off 6. Remove screws from top rail of stove that hold the side panel. 7. Remove the screw on the back that hold the side... Read more

I ordered the brioler pan for my new stove from y'all it was a little small but that's the part number in the book that I got with the stoveyall did a great job fast shipping just what I ordered will by from again thanks Read more

The instructions that came with the replacement smaller surface heating element provided no help about how to open the top of the range, so I checked the internet. I found several videos on replacement of surface elements in flat top ranges, but none for our particular range, so I Google-searched a simple question, “How to open the top of a 6898VVD Magic Chef range”. The AI Overview answer had several points, most of them not useful, except for the last one: “Hidden Clips: There might be... Read more

Little procrastination paid off. With only 50% capability I knew it is time to call the appliancepartspros. They shipped me parts within 3 days. It was practical to fix both at the time. All I needed was to disconnect power at range breaker box, grab a screwdriver to lift top open, a 16 inch or so piece of old 2×4 wood to keep the top top of stove lifted, so I could access heating elements from underneath. Then I took my black sharpie And marked location of mounting screws and... Read more

Attached new handle with screws. Read more

• Door won't open or close

The replacement hinge unit arrived in just two days. The JennAire (Maytag) oven door is fairly typical in that it easily lifts off of the hinge bars. Once the door is off then removing two screws is all that's required to remove the hinge unit from the oven. The new hinge slides up into place and while you hold it up inside of its location putting the old screws back in is very easy. After sliding the door back down onto the hinge bars the oven is as good as new Read more

• Little to no heat when baking

It took 10 minutes and a screwdriver, remember to turn off power to the oven at the fuse box. By the way, I ordered the part at 1:30pm and received it at 12:30pm the next day using normal shipping, not bad. Read more