Magic Chef Refrigerator Parts

The Hinge Washer is an OEM replacement part for Whirlpool refrigerators. This small washer plays a supports the refrigerator door hinge assembly. Center hinge plastic washer.

Causes of a bad hinge washer are generally normal wear and tear from extensive use. As the washer absorbs pressure each time the door is opened or closed, it can gradually deteriorate or crack. Physical damage is also possible if the door is accidentally struck or slammed.

Symptoms of a worn or damaged hinge washer include:

• sagging doors
• uneven gaps around the door seal
• doors that do not stay securely closed on their own
• Over time and repeated opening/closing stress, the hinge washer compresss which affects door alignment.

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Evaporator Fan Motor is an OEM replacement part for Whirlpool refrigerators. It is responsible for circulating cold air inside the refrigerator compartment to maintain even temperatures. The evaporator fan motor works continuously to circulate air across the evaporator coil, where it is cooled and distributed throughout the fridge.

Causes of a bad fan motor can include debris accumulation hindering blade spin, failed motor windings from constant operation, or loose wiring connections interrupting power flow.

Symptoms include:

• Warm spots appearing in the fridge or freezer
• Inability to reach temperature set points
• Loud grinding or clicking noises from inside

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Radiant Heater is an OEM replacement part for Whirlpool refrigerators. It is the defrost heater that provides a gentle warmth to prevent freezing and freezing within selected drawers and compartments.  Radiant Glass (Quartz), Length (Approx) - 9-1/4, 500 watts

Causes of a faulty heater can include operational wear from prolonged power on cycles. Exposure to condensation or spills may also impact insulation over time.

Symptoms include:  

• Inadequate or ineffective temperature control in heater zones
• Short cycling or failure to maintain set temperatures  
• Loose connections or damage to heating coils

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Roper refrigerator models.

The Refrigerator Thermostat is an OEM replacement part for Whirlpool refrigerators. This part monitors and maintains the temperature inside the appliance.

Causes typically relate to normal component degradation over extended use.

Symptoms of a faulty thermostat can include:

• ineffective or fluctuating interior conditions
• higher than normal energy usage
• intermittent compressor cycling
• potentially complete cooling loss in extreme cases

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Door Handle is an OEM part for Whirlpool refrigerators. This handle provides a sturdy grip for opening and closing the refrigerator door, ensuring easy and convenient access to the appliance's contents.  

Causes of a bad door handle can include normal wear and tear, repeated use, or accidental damage.  

Symptoms of a bad door handle include:

• The handle feeling loose or wobbly
• Cracks or visible damage to the handle
• Difficulty in opening or closing the refrigerator door
• The handle detaching from the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Ice Crusher Bucket is an OEM part for Whirlpool refrigerators. It serves as a container for holding and crushing ice from the icemaker. The bucket houses the crushing mechanism that breaks down ice cubes into smaller pieces, making it convenient for dispensing crushed ice through the refrigerator's door.

Over time, the ice crusher bucket can become worn out or damaged due to regular use, exposure to moisture, or accidental impact.  

Symptoms of a bad ice crusher bucket include:

• The bucket not holding ice properly
• Issues with dispensing crushed ice
• Unusual noises during ice crushing
• Visible cracks or damage to the bucket

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Ice Door Fountain Kit is an OEM replacement part for Whirlpool refrigerators with built-in ice makers. It directs water to the ice molding trays and facilitates automated ice cube harvesting. Kit includes flapper, solenoid, strike arm, solenoid plunger, and instructions. Spring is not included. For the spring order 61004388.

Causes of a bad ice door fountain kit can include wear and tear over time, buildup of ice or debris obstructing the door mechanism, or damage to the components from frequent use.

Symptoms include:

• Incomplete ice cubes or low ice yield
• Drips or leaks in the ice maker area
• The ice drawer fails to eject cubes fully

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This ice maker cover shields the front of the ice maker assembly, protecting the module and moving parts from dust and accidental contact. Replacing a cracked or missing cover restores a clean, finished appearance and keeps components protected.

• Shields the ice maker's front components and control module
• Helps keep dust, splashes, and debris out of the mechanism
• Prevents accidental contact with moving ejector parts
• Replace if the cover is cracked, warped, missing, or will not stay attached

• Unplug the refrigerator before servicing
• Access the ice maker in the freezer compartment
• Carefully release the retaining tabs and remove the old cover; note orientation
• Align the new cover and press until it snaps securely into place—do not force the tabs

The Light Socket Kit is an OEM part for Whirlpool refrigerators. This kit includes the light socket and necessary components to ensure proper installation and functionality. It is designed to hold the refrigerator light bulb securely and provide reliable electrical connections to illuminate the interior of the refrigerator.

Common causes of failure include wear and tear, corrosion from moisture, or damage from handling or bulb replacement.

Symptoms of a bad Light Socket Kit include:

• Refrigerator light not turning on
• Flickering or intermittent lighting
• Visible damage or corrosion on the socket
• Burned or melted areas around the socket

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rinse Aid Cap is an OEM part for Whirlpool dishwashers. It is designed to securely cover the rinse aid dispenser, ensuring the proper release of rinse aid during the wash cycle to improve drying performance and prevent water spots on dishes.

Causes of a bad rinse aid cap can include wear and tear over time, damage from accidental mishandling, or loss of the cap. Without a properly functioning cap, the rinse aid may not dispense correctly.

Symptoms of a bad rinse aid cap include:

• Rinse aid leaking or not dispensing
• Water spots or streaks on dishes after drying
• The cap not fitting securely or being visibly damaged
• The rinse aid compartment remaining full or not using rinse aid as expected

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Ice Chute Door is an OEM replacement part for Whirlpool side-by-side refrigerators. It provides access to the dedicated ice and water storage and dispensing compartment located on the refrigerator door.  

Causes of a faulty chute door can include normal wear from frequent use. Internal temperature fluctuations may cause durability issues over several years.

Symptoms of problems include:

• Failure to fully close or form a tight seal  
• Difficulty dispensing ice or water due to door misalignment
• Premature cooling loss from unsealed opening
• Physical damage preventing proper closing

This OEM door is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore side-by-side refrigerators.

The Water Inlet Valve Assembly is an OEM part for Whirlpool refrigerators. This assembly controls the flow of water into the refrigerator's ice maker and water dispenser, ensuring that water is supplied efficiently and consistently.  

Causes of a bad water inlet valve assembly can include mineral buildup, wear and tear over time, electrical malfunctions, or damage from freezing.  

Symptoms of a bad water inlet valve assembly include:

• The ice maker not producing ice
• The water dispenser not dispensing water
• Leaks or puddles forming around the refrigerator
• Unusual noises coming from the valve area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Leveling Leg is an OEM part for Whirlpool ranges. It's designed to ensure your range is perfectly balanced and stable on uneven floors. By adjusting the height of the leveling legs, you can prevent wobbling and ensure that your cooking surface is perfectly horizontal, which is critical for even cooking and baking.

Causes of a malfunctioning Leveling Leg can stem from physical impact damage, corrosion in humid conditions affecting integrity and adjustability, and wear over time, particularly if frequently adjusted or cleaned aggressively.

Symptoms of a bad Leveling Leg include:

• The range tilts or wobbles, making cooking uneven.
• Difficulty sliding pots and pans across the cooking surface due to the appliance not being level.
• Increased strain on other components of the range, which could lead to premature wear or failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This icemaker fill cup and bearing assembly directs water from the inlet tube into the ice mold and provides the pivot point for the shutoff arm. Replacing a cracked or missing cup helps stop leaks, misdirected fills, and inconsistent ice production.

• Channels incoming water into the ice mold to prevent splashing and overfilling
• Provides the pivot/bearing for the ice level (shutoff) arm
• Helps maintain consistent cube size and reliable icemaker shutoff
• Typical symptoms: water or ice buildup under the icemaker, overfilling or hollow/irregular cubes, or a loose/binding shutoff arm

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the ice bin and detach the icemaker to access the side-mounted cup
• Position the new cup directly under the fill tube; secure with existing hardware and verify the shutoff arm pivots freely in the bearing
• Restore power and water; run a test fill and check for leaks

This refrigerator defrost thermostat senses evaporator temperature and controls power to the defrost heater. It melts frost when needed and shuts the heater off at a safe temperature to protect components and keep cooling performance steady.

• Monitors coil temperature and opens/closes the defrost heater circuit
• Terminates the defrost cycle at a safe cutoff to prevent overheating
• Helps keep the evaporator clear of ice so air can circulate
• Common symptoms: heavy frost on the freezer back wall/evaporator, warm refrigerator section, fan noise from ice, long run times with little or no defrosting

• Disconnect power before service; use cut-resistant gloves
• Access the evaporator behind the freezer rear panel and fully thaw any ice using heat-safe methods—never chip or pry
• Reinstall the thermostat in the original location with firm metal-to-metal contact on the evaporator; route and secure wiring as originally
• After reassembly, verify defrost operation and confirm unobstructed airflow

The Single Water Valve is an OEM part for Whirlpool refrigerators. This valve controls the flow of water to the refrigerator’s ice maker and water dispenser, ensuring a consistent and reliable supply of water for ice production and dispensing.

Causes of a bad single water valve can include wear and tear over time, mineral buildup from hard water, or electrical malfunctions. 

Symptoms of a bad single water valve include:

• No water dispensing from the refrigerator
• The ice maker not producing ice
• Leaks around the valve area
• Unusual noises when the water dispenser is activated

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.