Maytag Cooktop Switch

This burner switch controls the power and heat settings for a surface cooking element, restoring reliable on/off operation, accurate temperature selection, and consistent element cycling on compatible electric ranges. What it does

• Regulates electrical power to a surface burner so the element heats to selected settings and cycles to maintain temperature.
• Replaces a worn or failed switch that causes a burner to not heat, not respond to knob changes, or only work on certain settings.
• Stops intermittent operation or arcing at the switch caused by worn contacts.
• Helps resolve a burner that stays on or will not turn on when the switch is faulty.

• Always disconnect power at the breaker before starting any repair to avoid shock.
• Photograph and/or label wires before removal so you can reconnect terminals correctly.
• Handle terminals gently and ensure secure, tight connections; replace any damaged wiring or connectors.
• Test the range on all heat settings after installation; if you see arcing, burning smell, or continued malfunction, cut power.

For switch mounting nut, order part# WP422617.

This main wire harness routes power and control signals between the appliance's control board and components to restore electrical connectivity and reliable operation. Replacing a damaged harness helps eliminate intermittent faults and lost functions. What it does:

• Provides the primary electrical connections between the control board and motors, switches, sensors and valves
• Carries power and signal wiring so controls and components operate as intended
• Commonly replaces harnesses with broken, melted, or corroded wires or connectors
• Can resolve symptoms such as no power to components, intermittent operation, or unresponsive controls

• Disconnect power to the appliance before inspecting or replacing the harness
• Compare connector types and routing to the original harness; install in the same path to avoid chafing
• Secure connectors fully until they click; avoid pulling on individual wires
• If wiring or connectors show heat damage or corrosion beyond the harness, inspect associated components.

Fix cooktop electrical failures or unresponsive controls with this wire harness. Restores power and signal connections between components.

Burner won't adjust heat or jumps to full power? This infinite switch restores variable temperature control to surface burners. DIY install in 30 minutes.

This right-side burner switch controls heat output on the cooktop so burners respond correctly to your knob settings. It restores proper power and temperature control for a single right-side heating element. What it does:

• Replaces a worn or faulty right burner control to restore variable heat settings
• Enables proper on/off function and temperature regulation for the right cooktop element
• Commonly used when a burner won't heat, only works at certain settings, or cycles unexpectedly
• Works with ranges that use a separate switch for the right front/right rear heating element

• Disconnect power at the breaker before attempting any repair to avoid shock
• Handle wiring terminals carefully; verify connections match the original before reassembly
• Use proper tools and avoid overtightening mounting hardware to prevent damage

If your cooktop burner won't heat, stays on one setting, or heats erratically, this control switch regulates power to restore proper temperature selection.

This control switch is the user-facing rotary selector that lets the appliance select cycles and settings. It restores clear, tactile control so the unit responds correctly when you turn the knob. What it does:

• Selects operating cycles and settings when the knob is turned
• Routes electrical signals from the control panel to the selected function
• Commonly replaced when settings do not change or the control feels loose/slips
• Resolves intermittent or unresponsive cycle selection and erratic behavior

• Disconnect power before attempting any repair to avoid electrical shock
• Accessible from the control panel; remove trim or console as needed per your model's service instructions
• Test function after reassembly; do not force the selector or use excessive torque

Burner won't heat or stays on high? This infinite switch controls top burner temperature settings. Restores precise heat adjustment to your cooktop.

Burner won't heat or lacks variable control? This infinite switch restores stepless temperature adjustment to electric range surface burners. Moderate DIY.

Burner stuck on high or won't adjust temperature? This infinite switch restores variable heat control to electric cooktop surface burners. DIY repair.

This rotary control switch replaces a worn or failed selector used to change cycles or settings on compatible appliances, restoring reliable user input and exact position selection. Easy-to-replace direct-fit control component. What it does:

• Sends a user-selected position to the appliance control so the unit runs the chosen cycle or setting.
• Replaces a cracked, loose, or non-responsive control shaft or knob interface.
• Stops intermittent or no-response issues when turning the control knob.
• Restores tactile click/position feedback for accurate selection.

• Disconnect power before service to avoid shock risk.
• Access may require removing the control panel.
• Handle the switch and control shaft carefully to avoid damaging terminals or alignment tabs.

Fix a burner that won't heat or won't turn off with this cooktop burner control switch. Most DIYers complete this repair in under 30 minutes.