Maytag Dishwasher Parts

Located between the console and door

This dishwasher circulation pump and motor assembly moves wash water through the spray arms during the cycles. Replacing a failed or noisy unit restores proper water flow, spray pressure, and reliable cleaning performance.

• Circulates water from the sump through the spray arms during wash and rinse
• Provides the pressure and flow needed for effective cleaning
• Common failure symptoms: little or no spray action, poor cleaning results, loud humming/rumbling/grinding during wash
• Water leaking from the pump area can also indicate a problem with this assembly

• Disconnect power at the breaker and shut off the water supply before servicing
• Access from the bottom/front; remove the toe panel and pull the dishwasher out if needed for clearance
• Expect residual water; place towels or a tray to catch spill, and note wire/connector orientation before removal
• Ensure all connections and seals are properly seated; run a short fill/rinse to check for leaks before reassembly

This drain adapter assembly links the dishwasher's drain outlet to the drain hose leading to a sink drain or garbage disposer, creating a secure, watertight discharge path. Replacing a damaged adapter helps stop leaks and supports proper draining.

• Adapts and seals the outlet from the sump/pump to the drain hose or disposer
• Helps maintain proper discharge flow during the drain cycle
• Common symptoms include water under the unit and standing water left in the tub

• Disconnect power at the breaker and shut off water; bail out any standing water
• Access the drain outlet and place a towel or pan to catch residual water
• Move the hose clamp, remove the old adapter, and seat the new adapter squarely
• Reattach the hose, secure the clamp, and run a brief test cycle to check for leaks

Lower wash arm redirects pressurized water across the dishwasher's lower rack to rinse and remove food and residue, restoring intended wash coverage and improving cleaning performance. What it does:

• Directs jets of water through multiple spray holes to rinse dishes on the lower rack.
• Helps remove stuck-on food, film and spotting on plates, bowls and cookware.
• Replaces cracked, clogged or broken lower spray arms that can cause poor cleaning or leftover residue.
• Works with the dishwasher's pump flow to maintain proper spray pattern across the lower rack.

• Refer to your model's parts diagram and instructions; the arm commonly snaps or threads onto the lower spray arm mount and procedures vary by model.
• Always disconnect power to the dishwasher before servicing; follow basic safety precautions.
• Clean the filter and any debris from spray holes before installing to avoid re-clogging.
• Inspect the mounting clip or retaining nut when removing the old arm and replace if damaged.

Replacement fill hose that routes water from the household supply to the appliance's ice maker and water dispenser, restoring proper water delivery and helping prevent leaks or pooling from a damaged line. What it does

• Directs water from the inlet valve to the ice maker and dispenser for ice production and dispensing.
• Maintains steady water flow; prevents kinks and pinched lines that reduce flow.
• Replace if cracked, split, collapsed, or leaking.
• Common symptoms: reduced or no water to the dispenser or ice maker, visible leaks, or pooling under/behind the appliance.

• Turn off the water supply and disconnect power before servicing to avoid flooding and electrical hazard.
• Inspect and replace clamps or fittings as needed; ensure proper seating and a snug, leak-free connection without overtightening.
• Check for kinks in the hose and route it so it won't be pinched by the appliance or cabinetry.
• After installation, turn the water back on and test for leaks at all connections.

Color: Universal Silver

This dishwasher overfill control float mounts in the tub floor and rises with the water level to trip the float switch and stop filling. Replacing a warped or stuck float restores proper fill control and helps prevent leaks. What it does:

• Monitors tub water level and actuates the float switch to shut off the inlet valve
• Helps prevent overfilling and water leaking from the door
• Common symptoms of a faulty float include no fill, continuous filling/overfilling, or inconsistent water level

• Float and retainer

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; lift out the old float
• Access beneath the tub may be required to release/install the retainer
• Ensure the float stem engages the switch lever and moves freely; test-fill and check for leaks

Also considered middle sprayarm on some dishwashers having a rinse arm on the ceiling.

Keep utensils organized and secure during the wash. This silverware basket sits in the lower rack and holds flatware and small items so water can circulate freely for effective cleaning and to help prevent obstructions.

• Organizes forks, spoons, knives, and small items in the lower rack to keep them from moving during cycles
• Promotes proper spray coverage by allowing water to flow through the basket's grid
• Helps prevent loose utensils from blocking the spray arm or damaging internal components
• Replaces a cracked, warped, or missing basket; common signs include broken sections or utensils falling through

• Disconnect power at the breaker before servicing
• Remove the old basket and place the new basket in the lower rack; no tools required
• Ensure the basket sits flat and does not contact the spray arm
• Follow your owner's manual for safe utensil loading practices

Contains two, six foot long braided hoses with 90 degree ends.

This silverware basket organizes utensils in the lower rack of your dishwasher so water can reach them evenly. Replacing a cracked or missing basket keeps small items contained and helps prevent interference with the spray arm.

• Holds cutlery and small utensils upright during wash and rinse cycles
• Keeps small items from falling through the rack or onto the heater
• Replace if the basket is cracked, warped, melted, or missing sections
• May help with utensils tipping over, rattling, or blocking the spray arm

• Remove the lower rack, lift out the old basket, and position the new basket in the same location
• Ensure the basket does not obstruct the spray arm and the rack rolls freely
• Handle sharp utensil tips carefully; install with the dishwasher cool and empty

This impeller assembly replaces a worn or damaged wash-pump impeller to help restore water circulation and spray pressure for better cleaning. Commonly used in compatible Whirlpool wash pumps to address weak wash performance. What it does:

• Spins inside the wash pump to move water through spray arms; damaged fins reduce spray force and cleaning.
• Restores proper flow during wash cycles — symptoms of failure include weak or uneven cleaning.
• Reduces abnormal pump noise and motor strain when the impeller is intact; cracked or missing fins can cause humming or grinding.
• Works with the pump housing and seals to route water; a failed impeller can allow internal leakage or cavitation.

• Always disconnect power (and water, if applicable) before servicing the appliance.
• Inspect pump seals, gaskets, and surrounding components; replace any damaged parts to prevent leaks.

This door switch detects when the dishwasher door is fully closed and latched. Replacing a worn or intermittent switch restores reliable start/stop operation and ensures the safety interlock cuts power whenever the door is opened.

• Senses door-closed status and sends a signal to the control
• Interrupts power to the machine when the door opens
• Helps prevent operation with an unlatched door
• Typical failure symptoms: won't start, stops mid-cycle if the door is bumped, or only runs when pressing on the door

• Disconnect power at the breaker before servicing
• Access the latch/switch area by removing the inner door panel or console; note wire locations
• Transfer wires one at a time and secure the new switch in the bracket
• Verify latch engagement and switch actuation before restoring power

Also Order Spray Arm Seal

This part is a genuine OEM replacement control panel intended for use with dishwasher models.The control panel allows the user to select the desired cycles of the dishwasher. It houses the buttons and the display. The control panel could become broken or start to malfunction over time, which might include the buttons getting stuck or jammed, or the display failing to light up. When replacing any appliance part, the appliance should be turned off and unplugged from power to prevent potentially serious injuries from occurring. This part was manufactured by Whirlpool. This control panel is sold individually. It is intended for use with dishwasher models manufactured by Whirlpool, Maytag, Jenn-Air, Amana, Admiral, Norge, and other brands.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed