Maytag Dryer Parts

• No heat or not enough heat
• Takes too long to dry

Since finding out pulley on motor is factory installed, I had to order a new motor with new pulley on it. I could not remove old blower wheel from old motor, no matter how hard I tried so I had to purchase new blower wheel and new blower housing. I am super happy finding Appliancepartspros.com the prices, and my experience was great! I basically removed everything step by step, and then replaced with the new parts step by step. I had help by watching videos that were provided online before and... Read more

I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more

Replaced Thermal Cutoff sensor. Read more

It took less then 15 min. Read more

Put in new LED lighrt module you sent me Read more

Replaced the timer - This should have been a VERY easy repair however, there is a clip (holding the timer to panel) on the bottom of timer than must be removed with a pair of pliers. There is absolutely NO room to access this clip so I had to take apart much of the dryer to gain access. What should have been a 15 minute repair turned into a frustrating hour. Read more

I referenced the repair video. Very straightforward and easy. Only need 3 tools: 1/4 and 5/16 nut drivers and Philips head screwdriver. About 15 minute job. Surprising how much lint and dust build up inside the chassis, was able to clean that out too. Read more

I removed the front panel of the dryer by removing 2 screws and lifting it up and out. Then I removed 4 screws from the bracket holding the tub in place. I had previously removed the 4 screws from the rear inspection cover so I reached in and released the spring loaded belt that turns the tub and then removed the idler pulley wheel. The tub just lifts out at that point, exposing the 2 Drum support rollers in the rear. I removed the 2 rear drum support rollers and decided to order 2 of... Read more

Swithching the timer was easy enough once I used the knob to keep the timer in place. The dryer’s wiring diagram was helpful. Read more

I'm not an appliance mechanic and have never worked on a dryer before, but I have worked as an instrument technician and lightly dabbled in HVAC repairs. We moved from natural gas to a new home with propane, so purchased this kit to make the conversion. In my mind I thought it would be fairly quick and easy, change a few fittings, etc, but realized upon reading the instructions that I needed to disassemble most of the dryer. The work was straightforward but since this was my first time... Read more

Replaced idler pulley assembly. Read more

• No heat or not enough heat

I ordered all the parts necessary to replace the heating element and thermostat on a Sunday night. Appliance Parts Pros shipped on Monday AM and I received them on Wednesday. It took me 45 minutes to disassemble the dryer, replace the parts and have the dryer working again. It should be good for another 35 years which should cover me for my needs. Thanks again to Appliance Parts Pros for having the best service and always the correct parts. I am a huge fan of your company as you never... Read more

Identified the parts I needed on the AppliancePartsPros.com website using the Dryer model number. Delivery was within 3 days by courier - excellent. Parts fitted, console reassembled and my dryer was back up and running within 40 minutes. No more intermittent problems with the timer not working - brilliant!! Read more

Ordered replacement filter Read more

Dropped light panel by removing two screws with socket set. Unplugged two terminals and unclipped the light socket from the base. Then just clipped the new socket onto the base, plugged the connectors onto the terminals and remounted the base. Total job was less than 15 minutes. Read more

The 2 sensors that sit on top of the flame tube work together. The Thrmst F should check closed, as should the Cutoff-TML, in order for power to flow to the ignitor. If the Cutoff is open, it is usually because the Thrmst-F did not open soon enough. The Thermst-F will cycle, closed to open, and repeat, however the Cutoff-HTML is a one time switch. If it opens it will not return to closed, and subsequently the ignitor will not glow. Some professionals say that if one of these sensors fail, both... Read more