Maytag Range / Cooktop / Oven Parts

Supports and guides your range oven door for smooth opening and closing. Replace if your hinge is cracked, broken, or causing door misalignment issues.

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

Replace a damaged, frayed, or worn power cord on your gas range. This 18-gauge supply cord assembly with push-tie strain relief restores safe electrical connection.

Burner not heating or heating unevenly? This 8-inch surface element kit restores even heating on your electric range. Simple plug-in install in 15 minutes.

Replaces worn oven door seals that allow heat to escape or show visible damage. Creates a tight barrier to maintain temperature and efficiency. Confirm fit.

Fix oven not heating, F5 error codes, or blank displays. This electronic control board repair often takes 30-45 minutes with basic tools.

This natural-gas burner orifice spud meters the correct fuel flow for a 15,000-BTU surface burner. Replacing a clogged, damaged, or wrong-size orifice restores proper flame size, cleaner combustion, and reliable cooktop performance. What it does:

• Meters gas through a calibrated opening to the burner head for correct flame height
• Sized for a 15,000-BTU surface burner using natural gas
• Installs in the orifice holder/valve body beneath the burner
• Typical symptoms of a faulty or mismatched orifice: weak/small flames, yellow/sooty flames, uneven heating, delayed ignition, burner won't reach high heat

• 1 natural-gas 15,000-BTU orifice spud

• Shut off gas supply and disconnect power; allow all burners to cool completely
• Remove grates, caps, and burner heads; lift the top or access the orifice holder as required
• Match each orifice to the correct burner location by BTU rating; do not overtighten
• After reassembly, check all connections for leaks with a non-corrosive soap solution and verify proper flame color/size

• For natural gas applications only; use the correct LP/propane orifice when converting fuel types

This is a blower wheel used in the downdraft exhaust ventilation system of a range or cooktop. It mounts on the motor shaft and draws smoke, steam, and cooking odors down and out through the vent ductwork. Replace this part if the exhaust fan is noisy, vibrating excessively, or not moving air effectively despite the motor running.

This is the black glass cooktop surface that sits on top of the range, providing the cooking area where pots and pans are placed over the heating elements below. It serves as both the structural top of the range and the smooth cooking surface. Replace this glass top if it is cracked, chipped, or shattered, as damage can expose heating elements and create a safety hazard.

Distributes gas through ports to create an even cooking flame. Replace if cracked, clogged, or worn to restore proper ignition and consistent heat output.

Restores a tight seal between your oven door and frame to prevent heat loss and maintain accurate cooking temperatures. Replace if worn or damaged.

Captures airborne grease and cooking particles to protect your range hood blower and maintain effective ventilation. Replace when clogged or damaged.

Traps airborne grease and cooking residue from vent airstream. Replace when clogged to restore airflow and protect blower. Confirm fit by model.

If your electric range burner won't heat properly or won't turn off, this infinite switch controls power to the surface element. Moderate DIY repair.

Fix rattling or noisy oven fan with this convection fan blade. Restores proper airflow for even baking temperatures. Mounts directly on motor shaft.

LP broil burner orifice for gas ranges. Installs inside oven cavity at top. Replace if damaged, incorrect size, or missing to restore proper propane flow.