Maytag Range / Cooktop / Oven Parts

Replacement control knob for gas ranges. Attaches to the control shaft to select settings. Replace if cracked, stripped, or missing to restore use.

Burner cap set for gas range cooktops. Fits over surface burners to distribute heat evenly. Replace cracked, chipped, or missing burner caps.

Replace a damaged, frayed, or worn power cord on your gas range. This 18-gauge supply cord assembly with push-tie strain relief restores safe electrical connection.

This blower speed switch lets you select the blower/fan speed to restore proper airflow control in your appliance. It replaces a worn or faulty speed selector so the blower will respond correctly when you change settings. What it does:

• Controls the blower/fan speed so the appliance can run at selectable airflow levels
• Replaces a switch that is stuck, unresponsive, or only running at one speed
• Restores reliable electrical connection between the control circuit and blower motor
• Helps eliminate intermittent fan operation or loss of speed selection

• Disconnect power to the appliance before starting any repair.
• Verify wiring placement and retain original fasteners; wiring diagram for correct connections.
• Handle terminals carefully to avoid bending or damaging contacts.

Oven light won't turn on? This light transformer steps down voltage to power your oven cavity lights. Moderate DIY repair restores illumination.

If burners won't ignite or spark continuously, the spark module may have failed. This part distributes high-voltage pulses to ignite gas burners.

This Door Handle restores a solid, secure grip for opening and closing your microwave door. Replace a cracked or loose handle to bring back smooth door operation and dependable access to the cavity. What it does:

• Provides the external grip used to open and close the microwave door
• Transfers pulling force to the door's latch-release mechanism
• Helps ensure smooth, controlled door operation
• Replace if the handle is cracked, broken, loose, or missing

• 1 door handle

• Disconnect power to the microwave before servicing
• Protect the door glass and finish; support the door while working
• Access the handle screws from the inner door trim; secure the new handle without overtightening
• Verify the door opens, closes, and latches properly before restoring power

Burner head that distributes gas evenly across the burner. Replace if cracked, clogged, or corroded to restore proper flame distribution on your gas cooktop.

LP broil burner orifice for gas ranges. Installs inside oven cavity at top. Replace if damaged, incorrect size, or missing to restore proper propane flow.

Burner won't heat or has cold spots? This surface heating element restores reliable, controllable heat to your cooktop. Direct-fit replacement.

Replaces worn oven door seals that allow heat to escape or show visible damage. Creates a tight barrier to maintain temperature and efficiency. Confirm fit.

Oven shuts off at high temperature or won't heat? This high-limit safety thermostat may have failed. Restores normal heating. Easy DIY fix in 30 minutes.

Replace your cracked, broken, or peeling range burner control knob. Fits directly onto the burner valve stem for precise heat adjustment on cooktops.

Replacement oven bake burner for gas ranges with direct spark ignition. Distributes gas evenly under the oven floor. Replace if cracked, corroded, or damaged.

This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:

• Protects the line and control circuits from shorts and overloads
• Time-delay design helps prevent nuisance opening during startup surges
• When open, the unit will be completely dead—no display, lights, or response
• Repeatedly opening usually indicates an unresolved electrical fault that needs diagnosis

• 1 time-delay fuse

• Disconnect power at the breaker before servicing; some appliances can retain dangerous high voltage
• Replace only with the same type and rating specified by the manufacturer
• Inspect the fuse holder and wiring for heat damage or loose connections before reassembly
• If the new fuse opens immediately, stop and diagnose the underlying cause; never bypass or upsize a fuse

If your electric range burner won't heat properly or won't turn off, this infinite switch controls power to the surface element. Moderate DIY repair.