Maytag Range Switch

This rocker switch controls the exhaust function on the appliance's ventilation system. It restores reliable on/off control of the blower when the original switch becomes worn, sticks, or fails. What it does:

• Provides on/off control for the exhaust/blower circuit
• Replaces a faulty or intermittent rocker that prevents the vent from operating correctly
• Helps address symptoms such as blower won't start, won't shut off, or only works when the switch is jiggled
• Restores proper tactile feel if the old switch is loose, cracked, or stuck

• 1 rocker switch

• Disconnect power at the breaker before servicing
• Access the control panel and note wire positions or take a clear photo
• Transfer wires one at a time to the new switch; ensure terminals are fully seated—do not pull on the wires
• Reassemble panels, restore power, and test exhaust operation

This infinite switch controls the power level to a surface burner on an electric range or cooktop, allowing smooth, variable heat settings. Replacing a failed switch restores precise temperature control and reliable burner shutoff.

• Regulates power cycling to a surface element for low, medium, and high heat levels
• Common failure symptoms: burner won't heat, only heats on high, won't turn off, or fluctuates/uneven heat
• Mounts behind the control knob and controls a single surface burner
• Restores consistent heat selection and responsive knob control

• Disconnect power at the breaker before servicing
• Pull off the knob and access the switch from the control panel
• Note wire positions or take a photo; transfer wires one at a time to the new switch
• Secure the switch, reinstall panels/knob, and test burner operation

This surface burner ignition switch with protective shield mounts on the gas valve stem. When you turn the knob, it closes the circuit to the spark module to ignite the burner and the shield helps protect the switch from spills. What it does:

• Triggers the spark module to create a spark when the surface burner knob is turned
• Shield helps protect the switch from moisture, grease, and heat
• Typical symptoms of a failed switch: no spark, intermittent sparking, or continuous clicking
• One switch is used per burner valve; replace only the failed switch(es)

• 1 ignition switch with protective shield

• Disconnect electrical power and shut off gas supply before servicing
• Pull the knob straight off and remove the control/manifold panel to access the switch
• Transfer wires one at a time to the new switch; align on the valve stem and position the shield correctly
• Reassemble, restore power and gas, and verify proper spark at each burner

This dual infinite switch controls power to a dual-size surface element on your range or cooktop, restoring smooth, accurate heat adjustment. Replace a failed switch to regain proper temperature control and dual-ring operation.

• Regulates cycling power to the inner and outer circuits of a dual surface element
• Provides variable heat levels from low to high
• Common symptoms of a failed switch: element won't heat, only heats on high, can't adjust temperature, element won't shut off, inner or outer ring won't activate
• Restores reliable response when selecting single-ring or dual-ring settings

• Disconnect power at the breaker before servicing
• Remove the control/console panel to access the switch
• Photograph/label wiring and transfer leads one at a time to matching terminal markings on the new switch
• Reassemble, reinstall the knob, and test both single-ring and dual-ring operations

This surface-burner igniter switch mounts on the gas valve stem and signals the spark module when you turn the knob. Replacing a worn switch restores reliable top-burner ignition and helps eliminate intermittent or continuous clicking.

• Mounts on the surface burner gas valve and closes the circuit to the spark module as the knob is turned
• Triggers the igniter electrodes to spark so the burner lights
• Helps address: no spark when turning the knob, intermittent or delayed ignition, or continuous clicking/sparking
• Typical failure signs include needing to jiggle the knob to spark or sparking that won't stop after the flame is lit

• Disconnect electrical power; shut off gas supply if working near gas fittings; allow the appliance to cool
• Pull off the burner knob and remove the panel/top as needed to access the valve switch
• Move wires to the new switch one at a time to maintain correct connections; ensure the actuator aligns on the valve stem
• Reassemble, restore power, and test burner ignition

This blower speed switch lets you select the blower/fan speed to restore proper airflow control in your appliance. It replaces a worn or faulty speed selector so the blower will respond correctly when you change settings. What it does:

• Controls the blower/fan speed so the appliance can run at selectable airflow levels
• Replaces a switch that is stuck, unresponsive, or only running at one speed
• Restores reliable electrical connection between the control circuit and blower motor
• Helps eliminate intermittent fan operation or loss of speed selection

• Disconnect power to the appliance before starting any repair.
• Verify wiring placement and retain original fasteners; wiring diagram for correct connections.
• Handle terminals carefully to avoid bending or damaging contacts.

This dual surface element infinite switch controls power to an electric cooktop or range's dual radiant burner. It restores precise heat selection and lets you choose inner-only or full dual-ring operation when the original switch fails.

• Regulates power cycling to maintain the selected heat level on a dual radiant element
• Selects between inner-only and dual-ring operation on compatible burners
• Common failure symptoms: no heat, only runs on high, cannot adjust temperature, burner won't shut off, dual feature won't engage
• Restores consistent, controllable surface cooking performance

• Disconnect power at the breaker before servicing—this is a high-voltage component
• Pull the control knob and open the control panel or rear cover to access the switch
• Photograph/note wire locations; move wires to the new switch one at a time
• Secure the switch, reassemble, restore power, and test both inner and dual-ring settings

This door-activated switch detects when the oven door opens or closes and signals the appliance to control the interior light. Replacing a worn or failed switch restores dependable light operation and accurate door-status feedback.

• Senses oven door position and opens/closes the light circuit
• Controls the oven's interior light based on door position
• Provides door-status input to the control for normal operation
• Typical symptoms: light stays on, won't turn on, or flickers with door movement; door-ajar messages may appear

• Disconnect power at the breaker or unplug the unit before servicing
• Access the switch from behind the front frame or control area, depending on model
• Move wires to the new switch one at a time to maintain correct positions; secure with existing hardware
• Restore power and verify light operation with door open/closed before reassembly

This infinite switch replaces the surface-burner control on electric ranges, restoring variable heat selection for a single cooktop burner so you can adjust cooking temperature reliably. What it does:

• Regulates the power delivered to an electric surface burner to provide variable heat settings.
• Replaces a failed or worn infinite switch that prevents changing burner temperature.
• Common symptoms: burner won't heat, burner remains at one setting, heat level can't be adjusted, or heat is inconsistent.
• Use only with compatible range models.

• Disconnect power to the appliance at the circuit breaker before you begin.
• Access the control panel per your model's service instructions; note wire locations or photograph them before removal.
• Reconnect wires to matching terminals and secure mounting hardware; restore power and test the burner.

This surface burner infinite switch is the behind-the-knob control for an electric cooktop or range. It regulates power to a single surface element so you can dial in and maintain the heat you need.

• Regulates on/off power cycling to a coil or radiant surface element for variable heat control
• Helps address issues such as a burner not heating, only heating on high, not turning off, or fluctuating temperature
• Installs behind the control panel; connects with spade terminals to line, load, and element leads
• Single-surface-element control for one burner position

• Disconnect power before servicing; this component carries high voltage
• Note wire positions or transfer one wire at a time from the old switch to the new switch
• Secure the switch to the control panel and align the shaft with the control knob
• Reassemble and verify smooth low-to-high burner operation

This surface burner ignitor switch mounts on the gas valve and signals the spark module when you turn the knob to Lite. Replacing a faulty switch restores reliable clicking and ignition on the affected burner. What it does:

• Closes the circuit to send power to the spark module when a knob is turned
• Helps produce a steady spark at the electrode for quick burner lighting
• Common symptoms it may address: no spark on one burner, constant clicking with knobs off, or intermittent sparking
• Used on gas cooktops/ranges that employ one spark switch per burner valve

• 1 ignitor switch

• Disconnect power and shut off gas before servicing
• Remove the knob and access the control area to reach the switch on the valve stem
• Note wire positions; transfer wires to the new switch and align it correctly on the valve
• Reassemble, restore power/gas, and test for proper spark operation

This igniter switch assembly replaces a worn or failed switch that controls ignition to a gas burner or oven igniter, restoring reliable spark/ignition and consistent burner operation. What it does

• Acts as the electrical switch that signals the igniter or spark module to light a burner or oven
• Helps resolve intermittent or no-spark ignition symptoms and burners that fail to light
• Restores proper on/off switching for the ignition circuit when the original switch is damaged or worn
• Works as the direct replacement switch component in the ignition system

• One igniter switch assembly

• Disconnect power and shut off gas supply before starting any repair
• Use basic hand tools; handle wiring connectors carefully to avoid damage
• Verify part compatibility with your model before installation

This switch/wire lead assembly is used on select ranges and wall ovens to control a specific function. Replacing a worn switch restores positive on/off control and reliable power flow through the attached leads. What it does:

• Opens or closes the circuit for the assigned feature when actuated
• Routes power through the attached leads to the controlled component
• Symptoms can include: feature won't start, won't turn off, intermittent operation, or heat-discolored/burned terminals or wires
• May feel loose or fail to click/hold position compared to normal operation

• One switch with attached wire leads

• Disconnect power at the breaker before servicing
• Access the control panel or mounting area; note wire locations (take a photo for reference)
• Transfer wires one at a time to the new switch; reuse original mounting hardware
• Restore power and test the function before final reassembly

Color: Black. Instruction sheet included.

This infinite surface element switch controls the heat output of a cooktop/range element. Replacing a worn switch restores smooth, reliable temperature adjustment for the designated Flex element, preventing issues like stuck-on-high heat, no heat, or erratic cycling.

• Regulates power to the surface element by cycling on and off at the selected setting
• Dedicated control for the unit's Flex element circuit
• Common failure symptoms: element won't heat, only heats on high, won't shut off, or heats inconsistently

• Disconnect power at the breaker before servicing to avoid electrical shock
• Pull the control knob straight off; access the switch from the control panel and note its orientation
• Label and transfer wires one at a time to matching terminals on the new switch
• Reassemble, restore power, and test all heat settings for proper operation

This top burner valve switch mounts to a surface burner gas valve and closes the ignition circuit when you turn the knob to Lite. Replacing a worn switch restores dependable sparking and stops intermittent or nonstop clicking at the burners.

• Mounts on the surface burner valve and closes the ignition circuit at the Lite position
• Signals the spark module to fire the igniters so the burner lights
• Helps ensure quick, consistent burner ignition
• Common symptoms: no spark at a burner, intermittent ignition, or continuous clicking with knobs in Off

• Disconnect power and shut off the gas supply before servicing
• Pull off the burner knob and remove the control/manifold panel to access the valve switch
• Transfer wires one at a time and align the switch correctly on the valve stem; avoid overtightening
• Reassemble, restore power, test for spark with gas off, then relight and check for leaks