Maytag Refrigerator Gasket & Seal

This oven door gasket creates a tight seal between the oven door and cavity to help contain heat for more even cooking and reduce energy loss. It replaces a worn or damaged seal to restore proper door closure and performance. What it does:

• Seals the oven cavity to help maintain correct cooking temperatures and reduce heat leakage.
• Helps prevent smoke and odors from escaping during use.
• Can improve bake and roast consistency when an old gasket is compressed or torn.
• Reduces external door heat, improving safety near the oven face.

• Allow the oven to fully cool and disconnect power before starting work.
• Remove the old gasket and clean the channel or retainer of debris before installing the new gasket.
• Press the gasket into the door retainer evenly around the perimeter; ensure the seal seats fully with no twists.

The Freezer Door Gasket is an OEM replacement part for Whirlpool bottom-mount refrigerators. This white freezer door gasket is responsible for maintaining a tight air seal around the entrance to the freezing compartment. It helps retain cold air inside and prevents warm drafts or humidity from affecting food freshness and freezer efficiency. 

Symptoms of a bad freezer gasket include: 

• Difficulty keeping consistent temperatures inside the freezer section
• Visible moisture, frost, or condensation around the door perimeter
• Noticeable warm air infiltration reducing cooling performance

Causes of freezer gasket failure involve regular opening and closing of the door. Over time, the flexible material breaks down from continuous use exposing it to changing environmental temperatures. Physical damage from overstuffing shelves or slamming the door can also prematurely damage the gasket.

This OEM replacement is also compatible with some KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

This refrigerator door gasket seals the door to the cabinet to keep cold air in and moisture out. Replacing a worn or deformed gasket restores a reliable seal, steadier temperatures, and more efficient performance.

• Creates an air-tight seal around the door perimeter
• Helps maintain correct temperatures and reduce frost or condensation
• Supports proper door closing and overall cooling efficiency
• Replace if the gasket is torn, cracked, warped, hardened, or leaves gaps; if the door pops open; or if you see moisture/frost along the door edge

• Disconnect power; remove items from the door bins for access
• Pull the old gasket from the retainer; transfer/loosen corner screws if applicable
• Warm the new gasket (hot water or low-heat hair dryer) to relax it; seat the lip evenly, corners first
• Close the door and check for uniform contact; adjust with gentle heat and by leveling/hinge alignment if needed; allow up to 24 hours for the gasket to fully conform

This refrigerator door gasket replaces a worn seal to restore a tight, even closure around the door. A proper seal keeps cold air in and moisture out, helping maintain temperature, reduce frost, and minimize run time. What it does:

• Forms a tight seal between the door and cabinet frame
• Helps maintain set temperatures and reduce moisture intrusion
• Resolves frost or condensation at the door and frequent compressor cycling
• Common signs: torn, cracked, or warped gasket; gaps; door not sealing smoothly

• Includes: 1 door gasket

• Disconnect power before servicing; remove or secure contents for safety
• On many models, loosen the inner-liner screws or pull the old gasket from the retainer/channel to remove
• Warm the new gasket (warm water or low heat from a hair dryer) to relax shipping folds
• Seat corners first, then press the rest into the retainer; verify seal with a paper-slip test and adjust as needed

This gasket seals the FIP assembly to prevent air and moisture leaks, helping maintain proper temperature and efficiency. A worn or damaged seal can lead to condensation, frost buildup, or temperature fluctuations.

• Creates an airtight seal at the FIP interface to keep air and moisture out
• Helps reduce frost/ice accumulation and condensation around the assembly
• Can address issues like warm spots, frequent cycling, or visible gaps at the seal
• Restores proper sealing performance when the original gasket is cracked, flattened, or torn

• Disconnect power before servicing; wear cut-resistant gloves
• Remove cover/fasteners to access the FIP sealing surface
• Clean mating surfaces; install gasket evenly without stretching
• Verify even seating and recheck for pinches or gaps before reassembly

This FIP gasket forms a tight seal between refrigerator components, blocking air and moisture leaks. Replacing a worn or damaged gasket helps maintain stable temperatures, reduce frost/condensation, and restore efficient cooling performance.

• Creates an air- and moisture-tight seal between mating panels, liners, or ducts
• Helps maintain proper airflow and temperature balance inside the refrigerator
• Replaces a torn, compressed, or missing seal to restore proper sealing

• Disconnect power; if working near water lines, turn off the water supply
• Remove the old gasket and clean mating surfaces of residue or debris
• Align the new gasket to match the original orientation; seat fully into the groove or under clips/fasteners as designed
• Reassemble and check for uniform contact to ensure a complete seal

This door gasket seals the refrigerator/freezer door to help maintain proper temperature and reduce energy loss. A direct-fit replacement that restores the magnetic seal for better cooling performance. What it does:

• Re-establishes a tight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and moisture inside the compartment
• Improves cooling efficiency and may reduce excessive run time from a failing seal
• Stops drafts and prevents food spoilage caused by a poor door seal

• One door gasket

• Clean the door frame and remove old gasket before installing the new one
• Warm or flex the gasket as needed for easier positioning; ensure the magnetic seal seats evenly around the perimeter
• Check hinge alignment and door closing after installation to confirm a complete seal
• Follow appliance power-off and safety precautions; refer to the appliance manual for model-specific instructions

This is the rear crisper seal that fits along the back edge of the refrigerator crisper compartment to help maintain the crisper enclosure and reduce air leakage. It restores a tighter seal for better humidity control and food storage. What it does:

• Replaces a worn or torn rear crisper gasket to help reduce cold air loss from the crisper area
• Helps maintain crisper humidity so produce stays fresher longer
• Prevents gaps that can cause uneven cooling or frost build-up near the drawer
• Can reduce draft noise or rubbing caused by a damaged seal

• One rear crisper seal (matches OEM part number)

• Remove the crisper drawer to access the rear seal before replacing
• Peel out the old seal and press the new seal firmly into the gasket channel; ensure an even, continuous fit
• Avoid using sharp tools that could damage the cabinet or new seal
• Unplug the refrigerator or switch off power if needed for safe access to nearby components

The Gasket-Door (black) is an OEM component specifically designed for Whirlpool refrigerators. This rubber gasket forms a seal around the perimeter of the refrigerator door opening. It helps maintain interior temperatures and humidity levels.

Symptoms of a bad door gasket include:

• Inability to properly chill compartments and freezing performance issues  
• Excessive frost or moisture inside refrigerator sections
• Higher energy costs from inefficient temperature regulation
• Warm air infiltration indicated by higher than normal interior temps

Causes of degraded gasket performance typically include cracks, tears or compression set deterioration that compromise the sealed barrier over many years of use. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This replacement gasket seals the appliance door to help maintain proper temperature and improve efficiency. It restores the original sealing surface to reduce leaks and keep the compartment at the intended temperature. What it does:

• Creates a tight seal around the door to help prevent air leakage
• Helps maintain consistent internal temperatures for proper performance
• Reduces frost buildup and energy loss caused by a compromised seal
• Addresses symptoms like warm spots near the door, excess frost, or cycling issues

• Disconnect power (and water if applicable) before starting any repair
• Remove the door or access panel for easier replacement
• Fit the gasket into the channel evenly; avoid stretching or twisting the material
• Inspect the mounting flange and surrounding surface for damage before installation

This evaporator cover gasket seals the evaporator cover to the refrigerator cabinet, helping maintain proper airflow and reducing frost buildup behind the back wall. It restores a tight seal for more reliable cooling performance. What it does:

• Seals the evaporator cover to prevent air leaks that can cause frost or ice buildup
• Helps maintain consistent cold-air circulation in the freezer/refrigerator compartment
• Reduces chances of excessive frost, water pooling, or longer run cycles tied to air infiltration
• Supports normal defrost operation by keeping warm, moist air out of the evaporator cavity

• Disconnect power before servicing and allow the appliance to defrost if needed
• Remove the evaporator cover carefully; watch for sharp sheet-metal edges and retain fasteners
• Position gasket evenly around the cover mating surface; avoid stretching or creasing the seal
• If adhesive or clips are used, replace or reapply per OEM guidance to ensure a secure fit