Mcculloch Parts

This wire harness assembly is an authentic replacement for chainsaws. It is supplied from the manufacturer. The wire harness assembly connects to the ignition module. It is made of two wires. One of the wires carries the power from the coil to the switch, while the other wire attaches to the engine ground on one side and has a switch contact on the other side. The wires have a rubber insulated coating that helps to protect them from high heat. These wires can suffer damage in many ways. They could become frayed or cut, they could have been subject to extremely high temperatures, and more. When they are damaged, it can cause a continuity loss in the circuit which can shut off the saw. Owners should look for broken or frayed wires. They can also use a multimeter to check the wires for continuity. If there are issues, the wires should be replaced right away. The chainsaw wire harness assembly is a genuine OEM replacement part for use with chainsaws. The assembly is sold individually. It will work with select chainsaws from Craftsman, Husqvarna, Poulan, and Poulan Pro.

This chain brake is made to connect above the drum of a chainsaw. It has a metal band that goes around the drum and a handguard that also connects to the brake. When the guard is pressed forward, the brake band tightens on the clutch drum, making the chain stop immediately. The brake is pre-assembled and consists of both metal and plastic parts. The spring, brake band, and linkage are all metal, and the housing is plastic. A common chain brake problem is the brake band becoming worn out or damaged. This causes the brake to no longer stop the chain fast enough or at all. This can be incredibly dangerous, so it’s important to check the brake regularly. Installing a new chain brake is straightforward with this genuine OEM part sourced directly from the manufacturer. Just remove the clutch cover assembly, take off the old chain brake, and screw in the new kit. Be sure to wear gloves and let the engine cool completely before making repairs. Compatible with Craftsman, Poulan, and Poulan Pro chainsaws. Sold individually.

This is a complete set of gaskets designed as a set to make the most of chainsaw maintenance and repair. This OEM gasket kit contains seven unique gaskets that should be replaced whenever a chainsaw's motor is serviced or repaired. Gaskets are designed to ensure that fuel remains where it is intended within the engine and parts and does not leak or seep into other areas. The pressure is maintained in the machine through the use of effective gaskets and seals. This is a complete kit and comes with every gasket needed for chainsaws made by Craftsman, Husqvarna, Poulan, and McCulloch, among others. It does not come with any associated parts necessary for full chainsaw maintenance and will require disassembly of several systems to install the new gaskets.

This replacement starter spring is a genuine OEM model from Husqvarna. The starter spring, also sometimes called the recoil spring or recoil starter spring, is part of the entire starter assembly. It attaches to the fan and flywheel housing and is responsible for helping to retract the starter rope when it is pulled to engage the engine. Over time, the spring can wear out or become twisted. This can cause the starter rope to no longer retract or it can even seize up the entire starter assembly. Replacement of the spring is the only option and this OEM part can provide an exact fit for select engines. This part is designed for use with blowers, edgers, trimmers, and pruners that feature Husqvarna engines and that are manufactured by brands like Weed Eater, Poulan, and Husqvarna themselves. The starter spring is made of durable metal and is sold individually. Always disengage the spark plug and allow the engine to cool completely before beginning and repair projects, and protect the hands by wearing gloves.

This is an authentic OEM replacement ignition module built specifically for Husqvarna lawn appliances. An ignition module, also known as an armature-magneto, is an essential part of a combustion engine's ignition. The ignition module creates pulses of high voltage electricity that the spark plug uses to generate a charge and start the ignition. Without a functional ignition module, the spark plugs and ignition will not engage. The most common reason for an ignition module to break is if the spark plugs have gone bad or are missing from the ignition. The charge generated by an ignition module is quite high, so if the spark plugs are not in place to receive the charge, the high voltage can fry and melt the module. If the spark plugs are not receiving a spark but can carry a charge, the odds are that the ignition module has been fried and will need to be replaced. To make this repair, use a wrench set and screwdriver. Although this high-quality replacement part is designed specifically for Husqvarna appliances, it may also work with some Jonsered appliances, too. It comes sourced from the original manufacturer and does not include any additional hardware.

This is a genuine air filter replacement designed for use in select lawn and garden equipment engines. The air filter is responsible for catching debris and dirt that may be in the air as it comes into the engine. This prevents the engine from being damaged by debris or buildup. Over time, the air filter will become clogged and should be replaced as a part of routine maintenance. It is helpful to keep an extra air filter on hand in case of an emergency replacement need. This genuine OEM air filter is manufactured by Husqvarna and meets exact standards for compatible models. It can be used in select models of chainsaws from the brand, as well as some from Jonsered. This air filter is sold as an individual unit and does not include any additional parts or accessories. A screwdriver will be required for replacement. To replace the filter, allow the engine to cool. Then, remove the screws from the cover of the filter and take out the old filter. Put the new filter in place and replace the cover. Then, reattach the screws and the job is done. Be sure to wear gloves when performing engine repairs.

This is a replacement leaf blower tube. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a broken or defective leaf blower tube on a variety of different leaf blower models. This tube makes up part of the vacuum attachment assembly. It links the vacuum bag directly to the lower tube. This part can become worn with regular use and may require replacement. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. For more accurate information on how and where to install this mulcher kit, refer to the appropriate owner's manual and included diagrams.As an authentic replacement part, this leaf blower tube is suitable for use on several different lawnmower models manufactured by Husqvarna and Craftsman. This is a genuine part made of high-quality, durable materials and is sold individually.

This authentic OEM part is a replacement foam air filter for a gas-powered leaf blower. For a gas-powered engine to work, it must maintain a balance of fuel and oxygen. This means it is constantly taking in air from outside the engine. However, working in dusty areas can cause a lot of debris to mix with the air. A foam air filter helps to catch that debris before it can clog up an engine. After an extended period of use, though, the filter will become clogged. Replacing a foam air filter is an easy repair that will only require a screwdriver. Remove the air filter cover, take out the old filter, and put in the new filter. This part works with gas-powered leaf blowers from Poulan, Weed Eater, and Husqvarna and is sourced directly from the original manufacturer. It ships individually.

A piston ring is a component located between a piston and a cylinder and helps the engine operate correctly. This component maintains gas compression between the cylinder wall and piston, makes lubricating oil to prevent scuffing, transfers heat from the crown of the piston to the cylinder, and prevents the piston from hitting the cylinder wall. There are several signs that a piston ring needs to be replaced. Excessive smoke may come out of the engine, oil may be used more rapidly, and your equipment might have a decreased performance without the power it used to have. If the engine is still in good shape, but the rings have lost their tension, replacing the piston ring is the best solution. Inspecting the cylinder for wear is also important since damaged piston rings can lead to cylinder wear. This piston ring is a genuine OEM product directly from the manufacturer. It comes as an individual part. It can be used on hedge trimmer, leaf blowers, and trimmers from Husqvarna, Weed Eater, and Poulan. Several tools, including a screwdriver and wrenches, might be required to install the replacement part.

The flywheel is a heavy metal wheel that connects to the rotating shaft. Its purpose is to help regulate how power is delivered from the motor to the rest of the tool. Its weight and inertia oppose and moderate small changes in the speed of the engine and holds onto that energy for use when needed. The most common problem with flywheels is for them to crack. As the engine begins to age and other parts begin to break down, excess vibration in the engine can cause the flywheel to wear down, grate, and even shatter. The flywheel needs replacing when the motor begins slipping into the wrong gear. The exact steps for replacing the flywheel will depend on the specific model being repaired. It should only require a screwdriver. This is a genuine OEM replacement flywheel assembly for gardening hand tools like leaf blowers, edgers, weed eaters, and hedge trimmers made by Craftsman, Husqvarna, Weed Eater, Poulan, Poulan Pro, Paramount, Turf King. This part ships individually.

The Driver Spring is an OEM part for Husqvarna power equipment. It plays a crucial role in the mechanism of devices such as lawn mowers or trimmers, where it helps to transfer force efficiently within the engine or motor, facilitating smooth and effective operation. This spring is designed to maintain optimal tension and functionality under the stresses of regular use.

Symptoms of a bad Driver Spring include:

• Loss of power or efficiency in the equipment
• Unusual or excessive noise during operation
• The equipment failing to start or operate correctly

Causes of a bad driver spring can include metal fatigue from repeated stress, corrosion due to exposure to moisture and chemicals, or improper installation leading to premature wear.

Maintaining this part in good working condition is essential for the reliability and longevity of your Husqvarna equipment.

This is a leaf blower fan blade, also called an impeller. This is what creates the flow of air out of the machine that blows leaves, grass clippings, and other debris out of the way. Without this part, the leaf blower would be unable to move air at all. The leaf blower fan blade is subject to some wear and tear through normal use. It is also made of plastic and may degrade over time, eventually cracking. If the leaf blower is not moving air and the engine is running normally, this could be the problem. Replacing the leaf blower fan blade will require opening the blower motor housing. Locate the fan blade, remove the Torx screws, and then remove the old impeller. Install the new one, replace the screws, and then reassemble the housing. This replacement fan blade is made from plastic with a metal sheath/insert. Note that this is an OEM part, and it is sold individually. It fits over 44 different Craftsman and Husqvarna gas-powered leaf blowers.

This wrist pin retainer is an essential component that is used to secure the piston pin in many types of handheld lawn and garden equipment. The pin is made of durable metal, but if it is missing or has become damaged, the part will need to be replaced. A wrench set, screwdriver, and pliers will be needed to make the replacement. To replace the wrist pin retainer, get access to the piston and then take off any keeper rings included. Use tools to tap on the wrist pin retainer to make it come loose and take it out of the equipment. The replacement can be inserted into the same place and the equipment will need to be reassembled.This is a genuine OEM replacement part that is sourced directly from the manufacturer. The wrist pin retainer is designed to be used in trash compactors, string trimmers, leaf blowers, edgers, hedge trimmers, chainsaws, pole pruners, and carpet cleaners manufactured by Turf King, Craftsman, Paramount, Husqvarna, Broan, Weed Eater, Poulan, and Poulan Pro. The part is sold individually.

Here is an authentic clutch friction washer that is sourced from the manufacturer. It is for use with several types of handheld outdoor power equipment. Other names for the part include clutch friction disk and clutch washer. The washer works as a friction disk that will help create the proper fit between components in the machine, which helps to engage the clutch. It is made from durable metal. The clutch friction washer that comes with the machine tends to be durable, but it may still need to be replaced at some point. The washer could become corroded, or it could break. It could also become lost when the owner is performing other maintenance on the machine. A wrench and screwdriver will typically be needed to conduct the replacement. Owners should check their manuals to ensure the correct location for installing the washer. The genuine OEM clutch friction washer is sold individually. It can work with more than 150 models of chainsaws, hedge trimmers, and string trimmers. Brands that have models compatible with the part include Craftsman, Husqvarna, Weed Eater, Poulan, and Poulan Pro.

This piston pin retainer is an authentic OEM replacement part sourced directly from the manufacturer for use on gas-powered chain saws. This retainer holds the pin that connects the connecting rod and piston. This is a small metal ring that has an opening on one side. It should be replaced anytime the piston is accessed. When it is taken off during repairs, it loses its compression and should be replaced.Take the spark plug out to make sure the saw cannot be started. Refer to the chainsaw's model diagram for the exact location of the piston ring. Remove the side cover, bar, and chain from the saw. Take the top cover off and set the screws aside. Next, remove the starter assembly and top handle, then the clutch drum and clutch with a clutch removal tool. Continue to disassemble the saw until the piston is visible. Use needle-nose pliers to remove the piston pin retainer and install the new one. Reverse the steps to reassemble the chain saw. Reinstall the spark plug and check the chainsaw for proper operation.This piston pin retainer is a quality metal part that is sold individually. It is designed for use in chainsaws manufactured by Poulan, Husqvarna, and Jonsered.