Parts for Ge JES1384SF02: 01 - Microwave Parts

The Microwave Door Switch is an OEM replacement part for GE microwaves. It is crucial for safety functionality as it detects when the door is properly closed and latched before initiating cooking cycles. The switch prevents operation if the door is ajar.

Causes of a bad door switch can include wear and grime accumulation over many years of use, impact damage, or failures in the plastic actuator or electrical components.

Symptoms of a bad door switch include:

• The microwave failing to start cooking even with the door closed and latched
• Error messages related to the door position being displayed
• Inability to lock or properly sense the closed door position

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a light bu, and it is made for microwaves. This is a genuine replacement part made by General Electric. This specific light bu has a voltage of 120 and a wattage of 25.A new light bu might be needed if the current one does not turn on when the microwave door is opened. The light bu should also be on when the microwave is in use so that the user may see the food during the heating cycle. It is common for light bu to burn out over time and they are very easy to replace when needed.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with microwaves made by General Electric.

Fix unresponsive buttons or a blank display with this microwave control panel assembly. Restores touchpad and display functionality. Moderate DIY repair.

Fix a microwave that won't heat but runs normally. This magnetron generates the microwaves that cook your food. Professional repair recommended.

If your microwave turntable won't rotate or makes grinding noises, this shaded pole motor is the likely fix. Straightforward 20-minute repair.

Microwave suddenly lost power or won't heat? A faulty thermostat cavity can cause total failure. This housing secures the sensor for proper alignment.

This microwave magnetron thermostat is an authentic OEM part sourced directly from the manufacturer. It is used in microwave ovens to prevent fires and extensive damage to the machine if the magnetron overheats. If the thermostat reaches an unsafe temperature, determined by the factory, it will stop the microwave from cooking. If this happens, the magnetron thermostat may be the culprit and should be replaced. A built-in safety feature will prevent the microwave from working until the thermostat is replaced. To start, disconnect the power from the microwave. Use a screwdriver to remove the trim kit. Use a safety drill bit to remove the microwave panels. Locate the thermostat that is connected to the magnetron. To start, disconnect the wires and remove the thermometer from the microwave. Install the new thermostat and connect the wires. Reassemble the microwave and reconnect the power. Test to make sure the power works with the new thermostat installed.This magnetron thermometer is an electrical part that is sold individually. It is designed for use in microwave ovens manufactured by General Electric and Hotpoint.

Replacement power cord assembly for your microwave. Installs at the rear panel to connect your unit to wall outlet. Order if damaged, frayed, or missing.

This coupler connects two rotating shafts to transfer motor power to the driven assembly, restoring proper rotation and drive function. It's a direct-fit replacement that helps resolve drive interruptions and mechanical noise caused by a failed coupler. What it does:

• Joins the motor shaft to the driven shaft or gear assembly to transmit torque
• Restores rotation when a worn or broken coupler prevents the appliance from turning
• Reduces slipping and eliminates clunking or grinding noises caused by a damaged coupling
• Keeps shafts aligned to prevent premature wear of connected components

• Disconnect power before servicing to avoid electrical shock or injury
• Inspect mating shafts and fasteners for damage; replace damaged parts as needed
• Use basic hand tools; secure coupler per OEM torque/fastening recommendations

Line filter assembly for microwaves. Suppresses electrical interference from the power line. Replace if cracked, damaged, or missing for proper operation.

Replacement thermostat holder for your microwave. This mounting bracket secures the thermostat in place. Order a new one if yours is cracked or broken.

Secures the high voltage capacitor in your microwave. Replace if broken, loose, or missing to prevent capacitor movement and electrical hazards.

Microwave not heating or making loud humming noises? This high voltage capacitor stores electrical energy for the magnetron. Moderate difficulty repair.

Microwave not heating or heating poorly? This high-voltage diode converts AC to DC for the magnetron, restoring normal heating. Moderate DIY repair.

The Primary and Secondary Door Switch is an OEM replacement part for GE microwaves. This part interrupts the power supply to the microwave when the door is opened.   

Causes of bad door switches can include regular wear and tear, electrical malfunctions, or physical damage from slamming the door.  

Symptoms of a bad Primary and Secondary Door Switch include:

• The microwave not starting or operating intermittently
• The appliance operating with the door open
• The interior light not turning on or off appropriately

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fix a microwave door that won't close or latch properly with this door latch lever lock. Common repair for doors that pop open or fail to engage securely.

The Wave Guide Locking Button is an OEM part for GE microwaves. This small yet essential component secures the wave guide cover in place, ensuring that the microwave's internal components are protected from food particles and debris. It plays a key role in maintaining the microwave's efficiency and safety.

Causes of a bad wave guide locking button can include regular wear and tear, damage from frequent use, or accidental breakage. If the locking button is compromised, the wave guide cover may become loose, leading to potential damage or inefficiency in the microwave's operation.

Symptoms of a bad wave guide locking button include:

• Wave guide cover becoming loose or falling off
• Difficulty securing the wave guide cover in place
• Rattling noise inside the microwave
• Visible damage or wear on the locking button

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: This part is a quantity of one. Order quantity needed.

Lower door hinge for microwaves. Mounts to the base cabinet to support and secure the door. Replace if cracked, broken, or bent to restore proper alignment.

Replace a cracked, broken, or missing microwave foot. This support leg installs on the bottom of your microwave to stabilize and level the unit.

Fix a microwave that's overheating or not cooling properly with this blower wheel replacement. Restores proper ventilation and prevents shutdowns.

Color: clear. Measures about 13 inches in diameter.

This main wiring harness routes power and signals between the range/oven control and major components so the appliance can operate safely and reliably. It replaces a damaged or burnt harness to restore proper electrical connections. What it does

• Connects the control board to heating elements, switches, sensors and other major components
• Provides factory-style wire routing and factory-installed connectors for correct fit
• Helps resolve symptoms like intermittent power to elements, unresponsive controls, or ignition/control errors when caused by damaged wiring
• Prevents shorts and poor connections that can cause erratic operation or component failure

• Disconnect all power (unplug or shut off breaker) before starting any repair
• Verify connectors and routing match the original harness; replace any damaged clips or retainers
• Handle connectors by the housings; avoid pulling on individual wires

This door sub-assembly replaces a damaged or dented refrigerator door sub-panel to restore the door's appearance and support the outer door components. It provides the underlying structure for the exterior door finish. What it does

• Replaces a bent, dented, or corroded door sub-panel that can affect door fit and appearance.
• Restores the mounting surface for trim, handles, and interior components attached to the door.
• Helps the door close and seal properly by returning correct alignment when panel damage has caused misalignment.
• Prevents further wear or stress on attached hardware by supplying a solid backing structure.

• One door sub-assembly

• Experienced DIY installation recommended due to door weight and alignment requirements.
• Disconnect power to the appliance and remove food from the door area before beginning work.
• Handle sharp edges carefully and use appropriate tools to remove/replace fasteners without damaging adjacent panels.
• After installation, verify door alignment and that seals/gaskets seat evenly to ensure proper closing.

Microwave stops heating but clock still works? This door interlock switch monitors door position and prevents operation when the door isn't latched securely.

Replace your microwave door screen if damaged or torn to maintain proper shielding. Confirm fit with your model number before ordering this part.

Shields the waveguide opening from grease, moisture, and food splatter. Replace this mica cover if burned, cracked, missing, or worn to protect components.

This bag screw assembly secures and advances the collection bag so the appliance can contain and compact debris reliably. Replacing a damaged screw assembly restores proper bag positioning and smooth bag feed. What it does:

• Holds and guides the bag in the collection/compaction area so the bag stays in place during operation
• Replaces worn, stripped, or broken screw hardware that can cause the bag to slip or not advance
• Helps prevent bag bunching and improves consistent compaction and containment
• Works as the mechanical fastening/drive interface between the bag and the compactor/feed mechanism

• One bag screw assembly

• Disconnect power to the appliance before beginning work to avoid injury
• Access typically requires removing the access panel or compactor drawer; follow the appliance service manual for disassembly steps
• Inspect surrounding components (brackets, guides, fasteners) and replace any damaged parts to ensure proper fit