Parts for Crosley CDB350NB7B: Motor & Pump Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Dishes still wet after cycle or water not heating? The heating element heats water for cleaning and promotes drying. DIY repair in under 30 minutes.

Secures components and panels inside your dishwasher. Replace if cracked, broken, or missing to restore proper alignment and prevent rattling or shifting.

Secures the lower spray arm in place. Replace if tabs are broken, worn, or missing, causing the spray arm to detach or not lock down properly. Installs under filter.

Fix dishwasher drainage issues with this sump cover and filter. Screens debris from clogging drain lines. Easy DIY repair in 5-15 minutes with basic tools.

Seals the connection between the dishwasher tub and sump assembly. Replace if water leaks from the base or the gasket appears cracked or flattened.

Fix dishwasher leaks or poor drainage with a new sump assembly. This pump housing restores proper water circulation and stops leaks from cracks or clogs.

Secures the sump assembly and pump seal to prevent leaks and maintain proper water flow. Replace if damaged or during sump repairs. Confirm fit with model.

Replacement upper spray arm for dishwashers. Installs in the top rack area to distribute water during wash cycles. Needed when original is cracked or broken.

Replaces a cracked, broken, or damaged lower spray arm in your dishwasher. Snaps into the bottom sump assembly. Essential for proper water distribution.

Seals the upper spray arm delivery tube connection in your dishwasher. Replace if water leaks from the spray arm mount or arm becomes loose. Verify fit.

This tube delivers incoming water from the inlet valve to the wash system inside the dishwasher. It connects the water inlet to the tub or spray arm assembly to ensure proper water flow during fill cycles. Replace this feed tube if you notice leaks beneath the dishwasher, reduced water flow into the tub, or visible cracks and damage to the tube.

This metal mounting bracket secures the circulation pump motor inside the dishwasher. It holds the pump assembly firmly in place to prevent vibration and ensure proper alignment with the wash system. Replace this bracket if it is cracked, bent, or corroded, which can cause excessive noise, vibration, or misalignment of the pump during wash cycles.

This small check ball sits inside the dishwasher's drain pump or water inlet valve and acts as a one-way valve to prevent water from flowing backward through the system. It ensures water moves in the correct direction during wash and drain cycles. Replace this part if you notice water draining back into the tub after a cycle completes, the dishwasher isn't draining properly, or water is leaking from the pump area.

Noticeable wear, cracks, or deformation on the O-ring This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Seals the rear of your dishwasher's circulation pump to prevent leaks. Replace if you notice water pooling or dripping from the motor area.

Fix a dishwasher that won't drain or makes grinding noises. This drain pump assembly removes water after each cycle. DIY repair in under an hour.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

A rubber mounting grommet that cushions and positions components to reduce vibration and wear, helping parts seat securely for reliable operation. What it does:

• Cushions and isolates parts to reduce noise and vibration.
• Protects metal components and wiring from abrasion where they pass through openings.
• Helps maintain proper alignment and fit of the mounted component.
• Prevents premature wear by absorbing movement and impacts.

• Disconnect power to the appliance before servicing.
• Press-fit into place; ensure proper orientation and full seating.
• Inspect surrounding parts for damage and replace if worn.
• Use manufacturer-recommended replacement; do not use solvents or adhesives unless specified.

This is a plastic support bracket that holds the lower spray arm in place at the bottom of the dishwasher tub. It allows the spray arm to spin freely while maintaining proper water flow from the pump to the arm. Replace this support if the lower spray arm wobbles excessively, detaches during cycles, or if dishes on the bottom rack are not getting clean due to reduced water pressure.

This base is the lower cabinet support that helps keep the appliance stable and holds internal components in their correct position. Replacing a damaged base restores proper fit, alignment and reduces cabinet movement. What it does:

• Provides structural support for the appliance cabinet and mounting points
• Keeps internal components aligned and maintains correct clearance
• Helps prevent rocking, vibration and gaps at the bottom of the cabinet
• Protects lower components from contact with floor-level debris or uneven surfaces

• Disconnect power and, if applicable, water before beginning work
• Access may require removing the toe kick or lower access panels
• Keep track of mounting screws and brackets; use replacement hardware if original fasteners are corroded

Filters debris from dishwasher sump to protect pump and spray arms. Replace if warped, clogged, or dishes aren't cleaning properly. Verify fit by model.

This trap is a molded drain fitting used in select Frigidaire-built appliances. It helps keep water flowing in the correct direction while limiting backflow of air and debris, supporting proper drainage and reducing leaks or odors when the original fails. What it does

• Creates a water seal in the drain path to reduce backflow and odors
• Guides condensate or wash water toward the drain pan/outlet for proper removal
• Helps protect internal components by limiting debris entry into the drain path
• Common symptoms of a bad trap: slow or no draining, water pooling/leaks, unpleasant odors, or visible cracks/warping

• 1 trap

• Disconnect power and, if applicable, shut off the water supply before servicing
• Access the drain area per your model's service/owner documentation; place towels to catch residual water
• Note hose routing and trap orientation; transfer and securely reinstall any clamps or seals
• After reassembly, run a small amount of water through the system to check for leaks

Fix a dishwasher that won't spray water from arms or makes loud grinding noises. This circulation pump motor kit restores proper wash action. DIY: 1-2 hours.

Replacement mounting screw for dishwasher panels and components. Secures loose panels, brackets, and trim. Needed when original fasteners are missing, stripped, or worn.

Replacement mounting screw for dishwashers. Secures components and panels inside your dishwasher. Order a new screw if yours is stripped, missing, or damaged.

Replacement mounting screw for dishwasher panels, brackets, and trim. Secures loose components caused by missing, stripped, or damaged fasteners.

Secures water or drain hoses to fittings, preventing leaks and loose connections. Replace when hoses slip or drip to restore a tight seal.

Replacement mounting screw for dishwashers. Secures internal components, panels, and brackets. Order when original screw is stripped, missing, or broken.

Replacement mounting screw for dishwashers. Secures trim, panels, brackets, and internal components. Order when fasteners are missing, stripped, or corroded.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

If water remains in your dishwasher after draining or returns to the tub, the drain check valve may have failed. Easy 10-30 minute DIY repair.

Brass nut that secures the heating element to the dishwasher tub. Replace if cracked, split, or causing leaks around the element mounting area.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.