Parts for Lg WT1150CW/00: Outer Case Assembly Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This tub cover assembly attaches to the outer tub of the washer, finishing the tub opening and helping keep water and suds contained. Replacing a damaged cover helps prevent leaks and unwanted splashing from the tub rim.

• Forms the protective rim at the top of the tub to reduce splashing and leaks
• Helps guide laundry away from the tub edge during agitation and spin
• Restores a secure, rattle-free fit when original tabs or the ring are cracked
• Common signs it's needed: visible cracks, broken tabs, warped ring, water splashing from the top rim

• Disconnect power; turn off water supply and move the washer for safe access
• Remove the top/lid or surrounding panels as required by the model
• Release retaining clips/screws and any attached guides/hoses from the old cover; transfer reusable parts
• Seat the new cover evenly and snap/secure all tabs before reassembly; run a short fill/spin to check for leaks

This tapping screw fastens appliance panels and components for a secure, lasting hold. Replace stripped, rusted, or missing hardware to restore proper fit, reduce vibration and rattling, and keep brackets, covers, and trim tightly in place.

• Fastens metal or plastic panels, trim, or brackets to the appliance cabinet/frame
• Cuts its own threads in pre-drilled holes for a tight, reliable fit
• Helps maintain alignment and reduce movement that can cause noise
• Replace when the original screw is missing, stripped, corroded, or will not tighten

• Disconnect power and shut off water/gas before servicing
• Match the screw's position and length to the original hardware
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• Reuse any washers or spacers from the original assembly if present

The Pulsator Cap is an OEM part for LG washing machines. It is designed to secure the pulsator (or agitator) in place, ensuring proper movement of the wash plate during the wash cycle. This component helps in the effective distribution of water and detergent, promoting thorough cleaning of clothes.

You should replace this pulsator cap if it becomes damaged, lost, or worn out. Causes of a bad pulsator cap can include regular wear and tear, exposure to heavy loads, or damage from improper handling. A compromised cap can lead to inefficient washing and potential damage to the pulsator.

Symptoms of a bad Pulsator Cap include:

• The pulsator becoming loose or dislodged
• Unusual noises during the wash cycle
• Clothes not being cleaned properly
• The washer experiencing imbalance issues

This OEM LG part is also compatible with Sears/Kenmore models.

The Pulsator Assembly is an OEM replacement part for LG washing machines. It generates the agitation and pulsating motion that effectively cleans clothes during the wash cycle. This pulsator measures approximately 18 x 18 x 2.5 inches. 

Symptoms of a faulty pulsator assembly can include:

• Inadequate or inefficient washing performance
• Excessive noise or vibrations during the wash cycle
• Clothes becoming tangled or not properly agitated
• Error codes or indicators related to the pulsator or agitation system

Causes of a bad pulsator assembly include wear and tear over time, damage from foreign objects entering the wash tub, or issues with other components that impact the pulsator's operation.

This OEM LG part is also compatible with Sears/Kenmore models.

The Customized Screw is an OEM part for securing the wash plate in LG washing machines. This screw maintains the wash plate's position and stability during the washer's operation. The Customized Screw ensures the wash plate performs efficiently, contributing to the effectiveness of the washing process by enabling proper agitation and circulation of clothes.

Causes of a bad Customized Screw can include wear and tear over time, especially from the constant motion and stress during the wash cycles.  

Symptoms of a bad Customized Screw include:

• The wash plate becoming loose or detached
• Ineffective washing due to improper motion of the wash plate
• Unusual noises during the wash cycle indicating a loose component

This OEM LG part is also compatible with some Kenmore models.

This damper controls airflow between compartments to help maintain consistent temperatures and efficient cooling. It replaces a worn or failed damper to restore proper air distribution and reduce temperature swings. What it does:

• Regulates airflow between freezer and fresh-food compartments for balanced temperatures
• Can cause uneven cooling or warm fresh-food compartment when faulty
• May click, stick, or fail to open/close if broken or obstructed
• Works with the refrigerator's control system to adjust airflow based on settings

• Disconnect power before beginning any service to avoid electric shock
• Handle the damper and housing carefully to avoid damage to plastic fins or linkage
• Note orientation and actuator connection before removal to ensure correct reassembly
• Test operation after reinstalling by restoring power and cycling temperature controls

Replace a damaged or stripped leveling foot with this leg assembly. It supports the appliance and adjusts for height so you can level it on uneven floors, restoring stability and helping reduce vibration, noise, and movement. What it does:

• Provides adjustable height to properly level the appliance
• Supports the cabinet/frame to keep all corners in firm contact with the floor
• Helps reduce rocking, walking, vibration, and rattling noises
• Fixes: appliance wobbles or is unstable; foot is cracked/missing; threads are stripped; cannot be leveled

• One leg assembly

• Disconnect power and, if applicable, turn off the water supply before servicing
• Carefully tilt or raise the appliance; protect the floor from scratches
• Unscrew the old leg; thread the new leg in by hand and adjust height to level
• Ensure all feet contact the floor firmly and the unit is stable before use

This screw cap covers and protects an exposed screw head or mounting hole, restoring a clean, finished appearance and helping shield the area from dirt and moisture. Use it to replace a missing, cracked, or discolored cap.

• Conceals and protects a visible screw head or mounting hole
• Helps keep dust and moisture out of the opening
• Restores a clean, factory look when the original cap is lost or damaged
• Common symptoms: cap missing, cracked, loose, or won't stay in place

• Disconnect power and shut off water when working near electrical or moving parts
• Align the cap over the screw head or hole and press evenly until fully seated—do not force
• If removing an old cap, use a plastic pry tool to avoid scratching nearby surfaces
• Ensure the underlying screw or fastener is properly tightened before installing the new cap

This hardware washer sits beneath a screw or nut to spread load and help keep fasteners tight inside your appliance. Replacing a bent or missing washer restores a secure fit and can reduce vibration-related noise. What it does:

• Distributes clamping force to protect mounting surfaces
• Helps resist loosening from vibration and movement
• Restores proper alignment when a washer is damaged or missing
• Common symptoms: loose or wobbling parts, rattling noises, screws backing out

• 1 washer

• Disconnect power; if working on a washer, also turn off water supply
• Note the original hardware stack order and take photos for reference
• Place the washer between the fastener head or nut and the part being secured
• Tighten to manufacturer guidance; avoid overtightening to prevent damage

This replacement nut secures bolts or studs in your appliance. Replacing a missing or stripped nut restores a tight, reliable connection to keep brackets and assemblies stable and reduce vibration or rattling. What it does:

• Provides threaded retention for bolts/studs on panels, brackets, and assemblies
• Helps maintain alignment and stability during operation
• Typical failure signs: stripped threads, missing hardware, loose or rattling components, vibration
• Direct replacement for the original nut in the same location

• 1 nut

• Disconnect power before service; shut off the water supply
• Match thread size/pitch to the original; start threads by hand to avoid cross-threading
• Tighten with the correct tool; do not overtighten or damage mating parts
• Reinstall any washers/spacers in the original order and verify secure fit

This genuine hardware washer installs at the specific joint shown in your model's parts diagram. It spreads clamp force and keeps the connection aligned and secure to support smooth operation of the related component. What it does:

• Distributes fastener load and protects mating surfaces from damage
• Maintains proper spacing and alignment within the assembly
• Helps resist loosening from vibration over time
• Clues it may be needed or worn: loose/rattling parts, unusual vibration or noise, or visible wear at the fastener location; on some models, seepage at that joint

• 1 washer

• Disconnect power and turn off water supply before servicing
• Support the assembly, remove the fastener, and install the washer in the same orientation
• Tighten the fastener snugly without overtightening; replace any damaged bolts, nuts, or seals

The balancer assembly mounts to the washer's basket/tub to counterbalance loads during spin. When worn or damaged, it can cause shaking, banging, or out-of-balance errors. Replacing it helps restore smoother, quieter spin performance.

• Stabilizes the basket/tub during acceleration and high-speed spin
• Helps reduce vibration, banging, and washer "walking"
• Can prevent spin cycles from slowing or stopping due to imbalance

• Disconnect power and allow moving parts to stop before servicing
• Access is typically at the top of the tub/basket under the tub ring; remove covers as needed
• Note orientation; seat the assembly evenly and ensure all tabs/fasteners are fully engaged
• After reassembly, run an empty spin test to verify smooth operation

The Drain Pump Assembly is an OEM replacement part for LG washing machines. As an important part of the washer drain system, it drives the pumping action removing water from the tub at the end of each cycle.

Causes of drain pump failure include normal wear from continuous operation over time, foreign debris potentially clogging the impeller cavity, or mineral/scale buildup inhibiting pump function.

Symptoms of a faulty drain pump can include:

• Washer fails to fully drain water at the end of cycles
• Excess water remains in the tub requiring manual emptying
• Abnormal grinding/knocking noises emit from below the tub

This OEM LG part is also compatible with some Sears/Kenmore model washing machines.

This single wire harness restores the electrical connections between components in an appliance, allowing circuits to operate normally and helping resolve power or intermittent control issues. It's a direct-fit replacement used where the original harness is damaged. What it does:

• Re-establishes electrical pathways between controls, sensors, motors or lights
• Helps stop intermittent operation caused by frayed or broken wires and poor connector contacts
• Replaces burned, pinched, or otherwise damaged harnesses that can trigger no-power or failed-function symptoms
• Maintains factory routing and connector interfaces for proper fit and function

• One single wire harness

• Disconnect power (unplug or shut off breaker) before starting any work
• Follow factory routing; avoid sharp edges and heat sources that can damage wiring
• Ensure all connectors are fully seated and locked; secure harness with clips or ties as originally installed

This spring-style hose clamp secures flexible hoses to fittings to help maintain a watertight connection and prevent leaks. A simple replacement when the original clamp is worn, bent, or no longer holds tension. What it does:

• Holds washer, drain, or water-supply hoses firmly on barbs and fittings
• Restores clamping tension to stop drips or slow leaks at hose connections
• Prevents hoses from slipping off under pressure or vibration
• Helps maintain proper fluid flow by ensuring a tight seal

• One hose clamp

• Disconnect power and shut off water supply before servicing plumbing connections
• Use pliers or the appropriate clamp tool to expand and position the clamp; release slowly to seat it
• Replace any damaged or corroded hoses or fittings for a reliable repair

This suspension assembly supports and stabilizes the washer tub, absorbing movement so the machine can spin smoothly with less vibration and noise. Replacing a worn suspension helps reduce banging and out-of-balance interruptions for steadier, quieter cycles. What it does:

• Supports the wash tub and cushions movement during wash and spin
• Controls vibration to reduce noise and shaking
• Helps prevent out-of-balance stops and UE/UB error codes
• Common failure signs: excessive shaking, banging, tub leaning, or long spin times

• Suspension assembly

• Disconnect power and water supply before service; move the appliance for safe access.
• Components may be under spring tension—support the tub and use gloves/eye protection.
• Access varies by model; typically remove or lift the top/upper cabinet, then release the assembly from the tub and frame.
• After replacement, level the washer and run a spin test to ensure smooth operation.

The Drain Hose is an OEM part for LG washing machines. This hose is essential for directing used water out of the washing machine and into the household drain system, ensuring efficient water removal after each wash cycle. The hose measures 67.5 inches in length.

Causes of a bad drain hose can include wear and tear from repeated use, blockages from debris or lint, or physical damage such as cracks or splits. A compromised drain hose can lead to water leakage, improper drainage, or even flooding.

Symptoms of a bad Drain Hose include:

• Water not draining properly from the washing machine
• Leaks or puddles of water around the washing machine
• Visible cracks or splits in the hose
• Unusual sounds during the draining process

This OEM LG part is also compatible with Sears/Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This replacement lower cover restores the appliance's lower-front protection and appearance. It shields internal components from dust and debris while helping maintain proper airflow and a finished look at the base of the unit. What it does:

• Protects internal components and wiring located at the appliance's lower front
• Helps prevent dust, lint, and small debris from entering serviceable areas
• Restores the appliance's finished appearance after damage or corrosion
• Can reduce noise from loose or damaged lower panels when properly secured

• One lower cover

• Disconnect power and, if applicable, gas before servicing the appliance
• Remove the kick plate or access screws to access and remove the old lower cover
• Reuse original fasteners when possible; replace damaged clips or screws as needed
• Check fit and secure all fasteners; verify no wires or hoses are pinched before restoring power

This switch assembly is the microwave's door interlock module. It mounts to the latch board and contains the switches that confirm the door is closed, restoring consistent start/stop operation when worn or sticking switches cause intermittent "door" errors.

• Houses and positions the interlock micro-switches on the latch board
• Signals the control that the door is securely closed so the unit can run
• Common fixes for: won't start, stops when the door is jostled, "door" error messages, or runs but doesn't heat
• Helps correct intermittent operation caused by fatigued or misaligned switches

• Disconnect power before servicing; microwaves retain dangerous high voltage
• Remove the upper grille and control panel to access the latch area per your model
• Note wire locations and switch orientation; move connectors one at a time to the new assembly
• After installation, verify door latching and test operation before reassembly

The Tub to Pump Hose Assembly is an OEM part for LG washing machines. This hose connects the tub to the drain pump, allowing water to be efficiently drained from the washing machine during the spin and drain cycles.

Over time, the hose can become clogged, develop cracks, or experience wear due to constant water flow and agitation. Damage can also occur from accidental mishandling or impact, leading to leaks or improper drainage.

Symptoms of a bad Tub to Pump Hose Assembly include:

• Water leaking from the washing machine
• Slow or incomplete drainage
• Error codes related to drainage issues
• Excess water remaining in the tub after the cycle

This OEM LG part is also compatible with Sears/Kenmore.

The Detergent Box Assembly is an OEM part for LG washing machines. This part holds and dispenses detergent, fabric softener, and bleach at the appropriate times during the wash cycle, ensuring effective cleaning and care for your laundry.

Common causes of a bad detergent box include clogging or blockage from detergent residue, wear and tear from regular use, or damage to the dispenser mechanisms.

Symptoms of a bad Detergent Box Assembly include:

• Detergent, fabric softener, or bleach not dispensing properly
• Residue build-up in the detergent drawer
• Leaks or drips from the detergent box area
• Error codes related to detergent dispensing

This OEM LG part is also compatible with some Kenmore models.

The Softener Cap is an OEM part for LG washing machines. It serves as the lid and housing for the internal water softener that prevents mineral deposits from building up. The softener cap funnels water to and from the softener compartment during various stages of the wash cycle.

Causes of a faulty softener cap can include cracked or degraded seals over extended usage, impact damage distorting fit, or harsh cleaners affecting plastics over time.

Symptoms of a bad softener cap include:

• Water leaks from around the softener area  
• The cap not closing or sealing properly 
• Mineral buildup occurring prematurely
• The softener not functioning as intended

This genuine LG replacement is compatible with Sears/Kenmore machines.

This softener cap seals and directs fabric softener from the dispenser so it dispenses correctly during the wash cycle. Replacing a worn or cracked cap helps prevent leaks and ensures the softener flows into the drum at the right time. What it does:

• Seals the fabric softener reservoir to prevent drips and leaks during filling and storage
• Guides softener into the rinse cycle so the appliance dispenses at the proper time
• Replaces cracked, warped, or missing caps that cause leaking or improper dispensing
• Restores a secure fit between the dispenser assembly and the softener reservoir

• One softener cap

• Unplug the appliance or disconnect power before servicing
• Remove the dispenser drawer or housing to access the cap
• Press or snap the cap into place until fully seated; do not force or overtighten
• Inspect dispenser for residue or damage and clean before reinstalling

This nozzle assembly directs and focuses spray for proper cleaning or dispensing, restoring correct fluid flow and spray pattern. It helps maintain performance and prevents uneven distribution during operation. What it does:

• Directs spray or fluid flow to the correct area for cleaning or dispensing
• Restores even spray pattern and coverage for improved cleaning performance
• Helps stop erratic or weak spray caused by a damaged or clogged nozzle
• Can reduce leaking or overspray from a broken or misaligned nozzle

• One nozzle assembly

• Disconnect power and shut off water supply before starting
• Access may require removing exterior panels or dispenser components; keep track of screws and fasteners
• Inspect mounting gasket or seals and replace if worn to prevent leaks

The Hinge is an OEM replacement part for LG top-loading washing machines. This hinge allows the washing machine lid to open and close smoothly. One hinge is included in this pack. The hinges are held on by six screws.

Causes of failure can include general wear and fatigue from years of opening and shutting the lid. The connecting bracket may also become misshapen due to excessive weight loads.

Symptoms denoting worn hinges include:

• Difficulty lifting or controlling the lid's movement
• Grinding noises and sounds of strain coming from hinged areas
• Lids left ajar or not sitting completely flush after opening

This OEM LG part is also compatible with some Sears/Kenmore model washing machines.

The Housing Assembly, Clutch is an OEM part for LG washing machines. It is integral to the washing machine's transmission system, helping to engage and disengage the tub during wash and spin cycles.

You should replace this clutch housing assembly if it becomes worn out or damaged. Over time, the clutch can wear out due to repeated use, heavy loads, or poor maintenance. Additionally, debris or foreign objects can cause damage to the housing or internal components.

Symptoms of a bad clutch housing assembly include:

• Washing machine not spinning or agitating properly
• Excessive noise during wash or spin cycles
• The washer not completing cycles or stopping mid-cycle

This OEM LG part is also compatible with Sears/Kenmore models.

The Valve Assembly Inlet is an OEM part for LG washing machines. It controls the flow of water into the washer, allowing the machine to fill with the correct amount of water for each cycle. This ensures that your washer operates efficiently and effectively.

Over time, inlet valves can wear out or become damaged due to mineral deposits, electrical issues, or regular wear and tear.

Symptoms of a bad valve assembly inlet include:

• The washer not filling with water
• Slow or irregular water flow
• Water leaking from the valve area
• Error codes related to water intake on the washer's display

This OEM LG part is also compatible with Sears/Kenmore models.

The Hose Connector is an OEM part for LG washing machines. It controls the water flow during the wash and rinse cycles. This part is designed to facilitate a secure and leak-proof connection between different sections of the washing machine, such as the inlet valve and the tub, or the pump and the drain hose. Ensuring these connections are secure is vital for the efficient operation of the washing machine, preventing leaks and maintaining optimal water usage.

Causes of failure may involve cracks, splitting, or collapsed seals/gaskets, as well as excessive mineral or foreign deposits that can obstruct water flow.

Symptoms of a bad hose connector are:

• Slow or incomplete filling during wash cycles
• Water leaks at the supply valve or connector area
• Connector split, cracked or compromised fittings

This genuine LG replacement is also compatible with Kenmore washing machines.

Detergent housing assembly that holds and routes detergent to the washer dispenser, helping ensure proper detergent flow and reducing leaks or dispenser jams. Fits into the dispenser area to replace cracked, warped, or damaged housing components. What it does:

• Houses and channels liquid or powdered detergent into the dispenser and wash chamber
• Restores proper detergent release when the original housing is cracked, broken, or warped
• Helps stop leaks and detergent buildup around the dispenser area
• Works with the dispenser drawer and related seals to maintain correct flow

• Disconnect power and turn off the water supply before starting service
• Use basic hand tools and follow the washer service manual or OEM diagram for disassembly/reassembly
• Inspect and replace any worn seals or gaskets at reassembly to prevent leaks

The Stator Assembly is an OEM replacement part for LG washing machines. It is an electrical component inside the motor that converts rotational motion to electrical energy to power spinning motions.  Note: For the RPS or Hall Sensor, order part number AP7015078.

Symptoms of a faulty stator include:

• Slow or inefficient spinning, rubbing noises  
• The machine failing to fully drain or spin clothes
• Repeated blowouts or failure of related motor components

Causes can be wear and tear over extended use. Environmental factors like dust and moisture exposure may degrade insulation integrity. 

This OEM stator is also compatible with some Kenmore front-load washer models.

The Water Level Pressure Switch is an OEM replacement part for LG washing machines. It is an essential component that monitors and detects the water level within the washing machine tub during the wash cycle.

Symptoms of a bad water level pressure switch:

• Washing machine not filling with water or not stopping when the desired water level is reached
• Excessive water intake, leading to overfilling and potential leaks
• Error codes or indicators related to water level issues
• Washing machine not advancing to the next cycle due to incorrect water level detection

Causes of a bad water level pressure switch can include mechanical failure, electrical malfunctions, or blockages or debris preventing accurate water level readings.

This OEM LG part is also compatible with Sears/Kenmore washing machine models.

This rotor assembly is the rotating half of the direct-drive motor in your washer. It mates with the stator to spin and agitate the basket, restoring drive when the original rotor is worn, cracked, or stripped.

• Forms the magnetic rotor of the direct-drive motor to turn the wash basket
• Transfers motor torque directly to the tub for spin and wash action
• Common symptoms: no spin or agitation, starts then stops, loud grinding/clicking, motor-related error
• Visible damage may include cracked hub, stripped splines, or loose fit on the shaft

• Disconnect power and water; wear gloves and eye protection
• Access from the rear, remove the back panel, hold the basket, then remove the center bolt and pull the rotor straight off (strong magnets)
• Align splines/keyway, seat the rotor fully, and reinstall/tighten the center bolt securely
• Inspect the stator and hall sensor for damage before reassembly and test a spin cycle

The Water Level Pressure Switch is an OEM replacement part for LG washing machines. It is an essential component that monitors and detects the water level within the washing machine tub during the wash cycle.

Symptoms of a bad water level pressure switch:

• Washing machine not filling with water or not stopping when the desired water level is reached
• Excessive water intake, leading to overfilling and potential leaks
• Error codes or indicators related to water level issues
• Washing machine not advancing to the next cycle due to incorrect water level detection

Causes of a bad water level pressure switch can include mechanical failure, electrical malfunctions, or blockages or debris preventing accurate water level readings.

This OEM LG part is also compatible with Sears/Kenmore washing machine models.

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

The Clutch Motor is an OEM part for LG washing machines. This motor engages the clutch mechanism, allowing the washer to switch between agitating and spinning cycles effectively.

Causes of a bad clutch motor can include wear and tear over time, electrical issues, or mechanical failure due to overloading or improper use.

Symptoms of a bad clutch motor include:

• The washer not agitating or spinning
• Unusual noises during the wash or spin cycles
• The drum not rotating properly
• The washer stopping mid-cycle

This OEM LG part is also compatible with Sears/Kenmore models.

Replacement nut that secures drawer and trim components on compatible LG appliances. It restores a firm, vibration-resistant fastening to help prevent loosening, rattling, or misalignment during normal use. What it does:

• Secures drawer, trim or small mounting brackets to the appliance chassis.
• Helps stop loosened fasteners that cause rattling or misaligned panels.
• Provides proper thread engagement for a stable connection.
• Matches the appliance's original fastening point when used as the listed part.

• Always disconnect power to the appliance before beginning any repair.
• Use the correct-size wrench or socket; avoid overtightening to prevent stripped threads.
• Inspect mating screw/bolt and threads for damage; replace damaged hardware as needed.

This is a small OEM washer used with the washer's internal mounting hardware to provide proper spacing and secure fasteners. It helps keep assemblies aligned and prevents hardware from loosening during operation. What it does:

• Acts as a spacer and load distributor for bolts or screws in the washer assembly
• Helps maintain proper alignment of panels or components
• Reduces wear between mating metal parts
• Can prevent fasteners from backing out due to vibration

• One washer as pictured

• Always unplug the appliance and shut off the water supply before servicing
• Access the mounting location per the service manual or parts diagram; replace only like-for-like
• Install with the correct orientation and hardware; do not overtighten fasteners
• If other fasteners or parts are corroded or worn, replace them at the same time

The Top Load Washer Coupling Assembly is an OEM component specifically designed for LG brand top-loading washing machines. This assembly connects the agitator shaft to the transmission inside the washer, allowing oscillating motions to be transferred through the transmission from the motor. 

Symptoms include:  

• No agitator movement or flickering motions during wash cycles
• Grinding or clicking noises coming from the motor/transmission area
• Leaks or loose fluid from damaged housing components  
• Shaking or instability of the entire washing machine

Causes of a bad coupling assembly can include material failure from ongoing vibration exposure, loosened connection points allowing unwanted play, or cracks/breaks due to heavy impacts.

A replacement clutch housing assembly that secures the clutch coupling to the washer drive—restores proper drive engagement and helps eliminate slipping, grinding, or failure to spin. Designed as a direct-fit service part for affected LG washers. What it does

• Houses and supports the clutch coupling that links the drive to the transmission.
• Restores reliable transfer of drive force so the tub can agitate and spin.
• Helps stop symptoms like slipping between cycles, unusual grinding or vibration, and failure to spin.
• Replaces worn, cracked, or damaged housings that can cause poor clutch engagement.

• One clutch housing assembly

• Disconnect power and water supply before beginning any repair.
• Access typically requires opening the washer cabinet or back panel; follow your model's service manual.
• Inspect related clutch and transmission components while accessible.

This cover cap is a small plastic trim piece that restores a finished appearance and helps protect the underlying fastener or opening from dirt and debris. It's a simple cosmetic and protective replacement for worn or missing caps. What it does:

• Covers and protects exposed screws, fasteners or small openings on the appliance
• Prevents dirt, lint and moisture from entering vulnerable gaps
• Restores a clean, finished look to damaged or missing trim
• Common symptom: missing, cracked or loose cap that leaves a visible hole or exposed screw

• Disconnect power to the appliance before starting any repair
• Usually installs by snapping into place; may require removing an adjacent panel or fastener first
• Avoid excessive force to prevent breaking the plastic; use a plastic trim tool if needed

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.