Parts for Lg WT1701CV/01: Outer Case Assembly Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Pulsator Cap is an OEM part for LG washing machines. It is designed to secure the pulsator (or agitator) in place, ensuring proper movement of the wash plate during the wash cycle. This component helps in the effective distribution of water and detergent, promoting thorough cleaning of clothes.

You should replace this pulsator cap if it becomes damaged, lost, or worn out. Causes of a bad pulsator cap can include regular wear and tear, exposure to heavy loads, or damage from improper handling. A compromised cap can lead to inefficient washing and potential damage to the pulsator.

Symptoms of a bad Pulsator Cap include:

• The pulsator becoming loose or dislodged
• Unusual noises during the wash cycle
• Clothes not being cleaned properly
• The washer experiencing imbalance issues

This OEM LG part is also compatible with Sears/Kenmore models.

Replace a cracked or loose washer lid with this lid assembly for LG top-load models. It restores a secure close so the safety lock can engage, allowing cycles to start and helping keep water and debris contained.

• Covers the tub opening and interfaces with the lid lock so wash and spin cycles can run
• Helps contain splashes and prevents foreign objects from entering the tub
• Provides a stable, easy-to-open top for loading and unloading
• Common symptoms: cracked or broken lid, difficulty closing, misalignment with the lock/striker, or lid-related error messages

• Unplug the washer and turn off water; wait for all moving parts to stop
• Support the lid; remove hinge screws/fasteners from the rear/top panel
• Lift off the old lid, set the new assembly in place, and secure evenly
• Confirm proper alignment and engage the lid lock with a short test cycle

This customized screw secures factory components in compatible LG appliances. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit so panels, brackets, or assemblies stay properly aligned and safely mounted.

• Fastens a designated component per model design
• Maintains alignment and helps reduce vibration/noise
• Replaces missing, stripped, or corroded hardware
• Common signs: loose or rattling panels, misalignment, or an obviously missing screw

• Disconnect power to the appliance; shut off water or gas if applicable
• Use the correct driver size; support the part being secured
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• Transfer any washers, spacers, or caps from the original fastener if required

This damper controls airflow between compartments to help maintain consistent temperatures and efficient cooling. It replaces a worn or failed damper to restore proper air distribution and reduce temperature swings. What it does:

• Regulates airflow between freezer and fresh-food compartments for balanced temperatures
• Can cause uneven cooling or warm fresh-food compartment when faulty
• May click, stick, or fail to open/close if broken or obstructed
• Works with the refrigerator's control system to adjust airflow based on settings

• Disconnect power before beginning any service to avoid electric shock
• Handle the damper and housing carefully to avoid damage to plastic fins or linkage
• Note orientation and actuator connection before removal to ensure correct reassembly
• Test operation after reinstalling by restoring power and cycling temperature controls

Replace a damaged or stripped leveling foot with this leg assembly. It supports the appliance and adjusts for height so you can level it on uneven floors, restoring stability and helping reduce vibration, noise, and movement. What it does:

• Provides adjustable height to properly level the appliance
• Supports the cabinet/frame to keep all corners in firm contact with the floor
• Helps reduce rocking, walking, vibration, and rattling noises
• Fixes: appliance wobbles or is unstable; foot is cracked/missing; threads are stripped; cannot be leveled

• One leg assembly

• Disconnect power and, if applicable, turn off the water supply before servicing
• Carefully tilt or raise the appliance; protect the floor from scratches
• Unscrew the old leg; thread the new leg in by hand and adjust height to level
• Ensure all feet contact the floor firmly and the unit is stable before use

This cap screw is a factory fastener that secures appliance components. Replace a stripped, corroded, or missing screw to restore a tight, rattle-free fit and proper alignment of brackets, panels, and internal assemblies.

• Secures panels, brackets, or assemblies to the chassis or housing
• Maintains alignment to reduce vibration and rattling noise
• Replaces hardware with worn threads, corrosion, or a damaged head
• Common signs: loose/moving parts, buzzing or rattle, and inability to tighten

• Disconnect power (and water, if applicable) before service
• Match length and head style to the original; replace one fastener at a time to preserve alignment
• Start threads by hand to avoid cross-threading; use the correct driver; tighten snugly—do not overtighten
• If the receiving threads are stripped, repair or replace the mating component before final assembly

This hardware washer sits beneath a screw or nut to spread load and help keep fasteners tight inside your appliance. Replacing a bent or missing washer restores a secure fit and can reduce vibration-related noise. What it does:

• Distributes clamping force to protect mounting surfaces
• Helps resist loosening from vibration and movement
• Restores proper alignment when a washer is damaged or missing
• Common symptoms: loose or wobbling parts, rattling noises, screws backing out

• 1 washer

• Disconnect power; if working on a washer, also turn off water supply
• Note the original hardware stack order and take photos for reference
• Place the washer between the fastener head or nut and the part being secured
• Tighten to manufacturer guidance; avoid overtightening to prevent damage

This replacement holder is a small mounting bracket used to secure components inside the appliance, restoring proper alignment and support so parts sit firmly and operate as intended. Ideal when a cracked or worn holder causes instability. What it does

• Secures internal components or assemblies to prevent movement or vibration
• Restores proper alignment when a damaged holder allows parts to sag or shift
• Helps reduce noise from loose or unsecured components
• Commonly replaced when the original holder is cracked, broken, or missing

• Turn off and unplug the appliance before beginning any repair.
• Inspect surrounding clips and fasteners; replace any damaged hardware for a secure fit.
• Use appropriate hand tools; avoid forcing parts to prevent further breakage.

This is a customized screw used to secure appliance panels and components for a proper fit and safe operation. It replaces lost or damaged fasteners to restore stability and reduce rattling or movement. What it does:

• Secures panels, trim pieces, brackets, or internal components
• Restores proper alignment and prevents rattling or vibration
• Replaces missing or stripped fasteners that cause loose parts
• Helps maintain safe, reliable operation by keeping components fixed

• Disconnect power before servicing any appliance to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and do not overtighten to prevent damage to threads or plastic parts
• Keep removed fasteners organized to ensure correct reassembly

This replacement nut secures bolts or studs in your appliance. Replacing a missing or stripped nut restores a tight, reliable connection to keep brackets and assemblies stable and reduce vibration or rattling. What it does:

• Provides threaded retention for bolts/studs on panels, brackets, and assemblies
• Helps maintain alignment and stability during operation
• Typical failure signs: stripped threads, missing hardware, loose or rattling components, vibration
• Direct replacement for the original nut in the same location

• 1 nut

• Disconnect power before service; shut off the water supply
• Match thread size/pitch to the original; start threads by hand to avoid cross-threading
• Tighten with the correct tool; do not overtighten or damage mating parts
• Reinstall any washers/spacers in the original order and verify secure fit

This genuine hardware washer installs at the specific joint shown in your model's parts diagram. It spreads clamp force and keeps the connection aligned and secure to support smooth operation of the related component. What it does:

• Distributes fastener load and protects mating surfaces from damage
• Maintains proper spacing and alignment within the assembly
• Helps resist loosening from vibration over time
• Clues it may be needed or worn: loose/rattling parts, unusual vibration or noise, or visible wear at the fastener location; on some models, seepage at that joint

• 1 washer

• Disconnect power and turn off water supply before servicing
• Support the assembly, remove the fastener, and install the washer in the same orientation
• Tighten the fastener snugly without overtightening; replace any damaged bolts, nuts, or seals

This main PCB power control board assembly manages power distribution and electronic control functions for the appliance, helping restore normal operation when the original control board fails. What it does:

• Routes power to motors, valves, heaters and other major components under electronic control
• Interprets user inputs and runs programmed cycles or functions
• Can stop operation or produce error codes when a circuit or component fails
• Common symptoms include no power or display, unresponsive controls, intermittent operation, or recurring error codes

• One main PCB power control board assembly

• Disconnect power and water supply before servicing to avoid shock or injury
• Handle the board by its edges; avoid touching components or connector pins to prevent damage from static
• Transfer any brackets, harnesses or sensors exactly as removed and ensure all connectors seat fully
• If errors persist after replacement, verify wiring, sensors and fuses before assuming board fault.

The balancer assembly mounts to the washer's basket/tub to counterbalance loads during spin. When worn or damaged, it can cause shaking, banging, or out-of-balance errors. Replacing it helps restore smoother, quieter spin performance.

• Stabilizes the basket/tub during acceleration and high-speed spin
• Helps reduce vibration, banging, and washer "walking"
• Can prevent spin cycles from slowing or stopping due to imbalance

• Disconnect power and allow moving parts to stop before servicing
• Access is typically at the top of the tub/basket under the tub ring; remove covers as needed
• Note orientation; seat the assembly evenly and ensure all tabs/fasteners are fully engaged
• After reassembly, run an empty spin test to verify smooth operation

This display power control board assembly restores the appliance's front display and touch controls so you can see status and select cycles. It replaces a failed display PCB to recover normal control-panel operation and indicators. What it does:

• Powers and drives the control-panel display so icons, lights, and text are visible
• Interfaces touch/selector inputs to the main control system for user commands
• Can resolve symptoms like a blank or flickering display, unresponsive touch buttons, or missing status indicators
• Works as the dedicated display/control interface—does not include main control board functions

• One display power control board assembly (single PCB unit)

• Disconnect power before servicing; risk of shock if powered during replacement
• Handle the board by its edges and avoid static discharge (use a grounded wrist strap if available)
• Verify connector alignment and seating before restoring power; confirm operation after installation

The Drain Pump Assembly is an OEM replacement part for LG washing machines. As an important part of the washer drain system, it drives the pumping action removing water from the tub at the end of each cycle.

Causes of drain pump failure include normal wear from continuous operation over time, foreign debris potentially clogging the impeller cavity, or mineral/scale buildup inhibiting pump function.

Symptoms of a faulty drain pump can include:

• Washer fails to fully drain water at the end of cycles
• Excess water remains in the tub requiring manual emptying
• Abnormal grinding/knocking noises emit from below the tub

This OEM LG part is also compatible with some Sears/Kenmore model washing machines.

This spring-style hose clamp secures flexible hoses to fittings to help maintain a watertight connection and prevent leaks. A simple replacement when the original clamp is worn, bent, or no longer holds tension. What it does:

• Holds washer, drain, or water-supply hoses firmly on barbs and fittings
• Restores clamping tension to stop drips or slow leaks at hose connections
• Prevents hoses from slipping off under pressure or vibration
• Helps maintain proper fluid flow by ensuring a tight seal

• One hose clamp

• Disconnect power and shut off water supply before servicing plumbing connections
• Use pliers or the appropriate clamp tool to expand and position the clamp; release slowly to seat it
• Replace any damaged or corroded hoses or fittings for a reliable repair

Top cover replaces a damaged or worn cabinet top to restore the appliance's appearance and protect internal components from dust and moisture. It's a direct-fit exterior panel used where the cabinet top is cracked, dented, or warped. What it does:

• Covers and protects internal components from debris, moisture, and everyday wear
• Restores the appliance's cosmetic appearance by replacing a scratched or dented top
• Eliminates rattling or movement caused by a loose or damaged top panel
• Provides a secure surface for control panels, hinges, and trim to mount to

• Disconnect power before servicing; work on a cool, dry surface
• Remove any trim, control panel, or hinges that block access per your model's service instructions
• Lift off the old top and align the replacement; secure with the original fasteners

This suspension assembly supports the wash tub and absorbs vibration so your washer can run smoother and quieter. Replacing a worn suspension helps reduce shaking and banging and improves overall stability during spin.

• Supports and stabilizes the wash tub during wash and spin
• Absorbs vibration to reduce shaking, noise, and excessive movement
• Helps minimize out-of-balance interruptions and rebalance attempts
• Addresses symptoms such as banging during spin, excessive vibration, or a tub that sags/leans

• Disconnect power and water supply before servicing; wear gloves and eye protection
• Access the suspension from the cabinet/top as applicable and support the tub to prevent sudden drop
• Replace the assembly in the same location/orientation; ensure all connections are fully seated
• After installation, level the washer and run a test cycle to ensure smooth operation; many replace all suspensions as a set for balanced performance

The Drain Hose is an OEM part for LG washing machines. This hose is essential for directing used water out of the washing machine and into the household drain system, ensuring efficient water removal after each wash cycle. The hose measures 67.5 inches in length.

Causes of a bad drain hose can include wear and tear from repeated use, blockages from debris or lint, or physical damage such as cracks or splits. A compromised drain hose can lead to water leakage, improper drainage, or even flooding.

Symptoms of a bad Drain Hose include:

• Water not draining properly from the washing machine
• Leaks or puddles of water around the washing machine
• Visible cracks or splits in the hose
• Unusual sounds during the draining process

This OEM LG part is also compatible with Sears/Kenmore models.

This is a factory replacement parts assembly designed to restore proper fit and function of a specific component group in your appliance. Use it to replace a worn, damaged, or missing original assembly and maintain reliable operation. What it does:

• Provides a complete, preassembled component group specified by the manufacturer
• Restores proper alignment, support, and operation of the associated parts
• Helps resolve issues like looseness, rattling, misalignment, or intermittent function
• Direct-fit replacement engineered to match the original design

• One parts assembly

• Disconnect power (and shut off water or gas, if applicable) before servicing
• Refer to your model's service documentation for the exact location and procedure
• Handle sharp edges and components carefully; wear cut-resistant gloves
• Verify correct operation before final reassembly

This switch assembly is the microwave's door interlock module. It mounts to the latch board and contains the switches that confirm the door is closed, restoring consistent start/stop operation when worn or sticking switches cause intermittent "door" errors.

• Houses and positions the interlock micro-switches on the latch board
• Signals the control that the door is securely closed so the unit can run
• Common fixes for: won't start, stops when the door is jostled, "door" error messages, or runs but doesn't heat
• Helps correct intermittent operation caused by fatigued or misaligned switches

• Disconnect power before servicing; microwaves retain dangerous high voltage
• Remove the upper grille and control panel to access the latch area per your model
• Note wire locations and switch orientation; move connectors one at a time to the new assembly
• After installation, verify door latching and test operation before reassembly

The Tub to Pump Hose Assembly is an OEM part for LG washing machines. This hose connects the tub to the drain pump, allowing water to be efficiently drained from the washing machine during the spin and drain cycles.

Over time, the hose can become clogged, develop cracks, or experience wear due to constant water flow and agitation. Damage can also occur from accidental mishandling or impact, leading to leaks or improper drainage.

Symptoms of a bad Tub to Pump Hose Assembly include:

• Water leaking from the washing machine
• Slow or incomplete drainage
• Error codes related to drainage issues
• Excess water remaining in the tub after the cycle

This OEM LG part is also compatible with Sears/Kenmore.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This detergent box assembly replaces the washer's front detergent/dispenser drawer so detergents and additives dispense cleanly during cycles. It restores proper product delivery and helps reduce residue build-up in the dispenser area. What it does:

• Houses and channels liquid and powdered detergents and additives into the wash at the correct time
• Prevents detergent from pooling or leaking into the washer cabinet when functioning correctly
• Reduces visible residue and clogging in the dispenser area that can affect dispensing
• Compatible with front-load washer detergent/dispenser systems that use a removable drawer

• One detergent box assembly

• Remove power and water supply before beginning service
• Typically installs by sliding into the dispenser housing and securing any retaining clips or screws
• Inspect surrounding seals and rails for damage and clean any residue before installing the new assembly

The Softener Cap is an OEM part for LG washing machines. It serves as the lid and housing for the internal water softener that prevents mineral deposits from building up. The softener cap funnels water to and from the softener compartment during various stages of the wash cycle.

Causes of a faulty softener cap can include cracked or degraded seals over extended usage, impact damage distorting fit, or harsh cleaners affecting plastics over time.

Symptoms of a bad softener cap include:

• Water leaks from around the softener area  
• The cap not closing or sealing properly 
• Mineral buildup occurring prematurely
• The softener not functioning as intended

This genuine LG replacement is compatible with Sears/Kenmore machines.

This softener dispenser cap replaces the worn or cracked cap that covers the fabric softener chamber, restoring proper containment and controlled release of liquid softener during the wash cycle. A simple, low-cost part that prevents leaks and keeps the dispenser functioning. What it does

• Covers and seals the fabric softener compartment so liquid stays in the dispenser until the rinse cycle.
• Helps prevent softener from leaking into the washer drum between cycles.
• Restores a secure fit when the original cap is cracked, warped, or missing.
• Resolves issues with softener dispensing at the wrong time or pooling in the dispenser.

• One softener dispenser cap (1 piece)

• Disconnect power to the washer before accessing internal parts and follow all safety precautions.
• Typically accessed by removing the dispenser drawer or top panel—refer to your washer's service instructions.
• Inspect surrounding dispenser components for damage and replace any worn parts to ensure a proper seal.
• No electrical connections; basic hand tools may be required.

This nozzle assembly directs and focuses spray for proper cleaning or dispensing, restoring correct fluid flow and spray pattern. It helps maintain performance and prevents uneven distribution during operation. What it does:

• Directs spray or fluid flow to the correct area for cleaning or dispensing
• Restores even spray pattern and coverage for improved cleaning performance
• Helps stop erratic or weak spray caused by a damaged or clogged nozzle
• Can reduce leaking or overspray from a broken or misaligned nozzle

• One nozzle assembly

• Disconnect power and shut off water supply before starting
• Access may require removing exterior panels or dispenser components; keep track of screws and fasteners
• Inspect mounting gasket or seals and replace if worn to prevent leaks

This replacement door hinge restores smooth, aligned opening and closing. Replacing a worn or bent hinge helps the door sit squarely and seal or latch properly, preventing rubbing, binding, and premature wear on adjoining parts. What it does:

• Supports and pivots the door for smooth operation
• Maintains door alignment for proper latch/seal engagement
• Replaces bent, cracked, or loose hinges that affect door movement
• Common symptoms include door sagging, rubbing/binding, difficulty closing, or visible hinge damage

• One door hinge

• Disconnect power before servicing; remove door contents to reduce weight
• Support the door while removing hinge fasteners to prevent strain on the new part
• Transfer and reuse original hardware as required; tighten screws to manufacturer-recommended snugness
• Verify door alignment and operation after installation and adjust as needed

This factory parts assembly replaces a worn or damaged assembly to restore the appliance's original function and fit. It's a direct-fit replacement designed to simplify repair and reduce downtime. What it does:

• Replaces the original factory assembly to restore the affected mechanism
• Re-establishes proper alignment and connections for the related components
• Helps stop symptoms like intermittent operation, loose fit, or non-functioning mechanism
• Matches OEM form and mounting points for a straightforward swap

• One complete parts assembly as shown

• Always disconnect power before starting any repair
• Use basic hand tools; avoid forcing connectors or mounting tabs

The Housing Assembly, Clutch is an OEM part for LG washing machines. It is integral to the washing machine's transmission system, helping to engage and disengage the tub during wash and spin cycles.

You should replace this clutch housing assembly if it becomes worn out or damaged. Over time, the clutch can wear out due to repeated use, heavy loads, or poor maintenance. Additionally, debris or foreign objects can cause damage to the housing or internal components.

Symptoms of a bad clutch housing assembly include:

• Washing machine not spinning or agitating properly
• Excessive noise during wash or spin cycles
• The washer not completing cycles or stopping mid-cycle

This OEM LG part is also compatible with Sears/Kenmore models.

The Water Inlet Valve is an OEM replacement part specific to LG washing machines. It is an electronic solenoid valve located near the water supply inlet ports that controls the flow of water into the washer tub. The inlet valve precisely regulates water levels during different phases like filling, washing, rinsing, and spinning cycles.

Causes of a bad water inlet valve can include worn or faulty electronic components, mineral buildup obstructing valve movement, or damage to seals and diaphragms.

Symptoms of a bad water inlet valve include:

• Inability to properly fill the washer tub during cycles
• Water leaking or flooding from the valve area
• Erratic water temperature or varying fill levels between loads
• Cycles failing to advance due to inadequate or unregulated water flow

This OEM LG part is also compatible with Sears/Kenmore models.

The Hose Connector is an OEM part for LG washing machines. It controls the water flow during the wash and rinse cycles. This part is designed to facilitate a secure and leak-proof connection between different sections of the washing machine, such as the inlet valve and the tub, or the pump and the drain hose. Ensuring these connections are secure is vital for the efficient operation of the washing machine, preventing leaks and maintaining optimal water usage.

Causes of failure may involve cracks, splitting, or collapsed seals/gaskets, as well as excessive mineral or foreign deposits that can obstruct water flow.

Symptoms of a bad hose connector are:

• Slow or incomplete filling during wash cycles
• Water leaks at the supply valve or connector area
• Connector split, cracked or compromised fittings

This genuine LG replacement is also compatible with Kenmore washing machines.

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

Detergent housing assembly that holds and routes detergent to the washer dispenser, helping ensure proper detergent flow and reducing leaks or dispenser jams. Fits into the dispenser area to replace cracked, warped, or damaged housing components. What it does:

• Houses and channels liquid or powdered detergent into the dispenser and wash chamber
• Restores proper detergent release when the original housing is cracked, broken, or warped
• Helps stop leaks and detergent buildup around the dispenser area
• Works with the dispenser drawer and related seals to maintain correct flow

• Disconnect power and turn off the water supply before starting service
• Use basic hand tools and follow the washer service manual or OEM diagram for disassembly/reassembly
• Inspect and replace any worn seals or gaskets at reassembly to prevent leaks

The Stator Assembly is an OEM replacement part for LG washing machines. It is an electrical component inside the motor that converts rotational motion to electrical energy to power spinning motions.  Note: For the RPS or Hall Sensor, order part number AP7015078.

Symptoms of a faulty stator include:

• Slow or inefficient spinning, rubbing noises  
• The machine failing to fully drain or spin clothes
• Repeated blowouts or failure of related motor components

Causes can be wear and tear over extended use. Environmental factors like dust and moisture exposure may degrade insulation integrity. 

This OEM stator is also compatible with some Kenmore front-load washer models.

The Water Level Pressure Switch is an OEM replacement part for LG washing machines. It is an essential component that monitors and detects the water level within the washing machine tub during the wash cycle.

Symptoms of a bad water level pressure switch:

• Washing machine not filling with water or not stopping when the desired water level is reached
• Excessive water intake, leading to overfilling and potential leaks
• Error codes or indicators related to water level issues
• Washing machine not advancing to the next cycle due to incorrect water level detection

Causes of a bad water level pressure switch can include mechanical failure, electrical malfunctions, or blockages or debris preventing accurate water level readings.

This OEM LG part is also compatible with Sears/Kenmore washing machine models.

This rotor assembly is the rotating half of the direct-drive motor in your washer. It mates with the stator to spin and agitate the basket, restoring drive when the original rotor is worn, cracked, or stripped.

• Forms the magnetic rotor of the direct-drive motor to turn the wash basket
• Transfers motor torque directly to the tub for spin and wash action
• Common symptoms: no spin or agitation, starts then stops, loud grinding/clicking, motor-related error
• Visible damage may include cracked hub, stripped splines, or loose fit on the shaft

• Disconnect power and water; wear gloves and eye protection
• Access from the rear, remove the back panel, hold the basket, then remove the center bolt and pull the rotor straight off (strong magnets)
• Align splines/keyway, seat the rotor fully, and reinstall/tighten the center bolt securely
• Inspect the stator and hall sensor for damage before reassembly and test a spin cycle

The Water Level Pressure Switch is an OEM replacement part for LG washing machines. It is an essential component that monitors and detects the water level within the washing machine tub during the wash cycle.

Symptoms of a bad water level pressure switch:

• Washing machine not filling with water or not stopping when the desired water level is reached
• Excessive water intake, leading to overfilling and potential leaks
• Error codes or indicators related to water level issues
• Washing machine not advancing to the next cycle due to incorrect water level detection

Causes of a bad water level pressure switch can include mechanical failure, electrical malfunctions, or blockages or debris preventing accurate water level readings.

This OEM LG part is also compatible with Sears/Kenmore washing machine models.

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

The Clutch Motor is an OEM part for LG washing machines. This motor engages the clutch mechanism, allowing the washer to switch between agitating and spinning cycles effectively.

Causes of a bad clutch motor can include wear and tear over time, electrical issues, or mechanical failure due to overloading or improper use.

Symptoms of a bad clutch motor include:

• The washer not agitating or spinning
• Unusual noises during the wash or spin cycles
• The drum not rotating properly
• The washer stopping mid-cycle

This OEM LG part is also compatible with Sears/Kenmore models.

This multi wiring harness routes power and signals between components to restore reliable electrical connections in the appliance. It replaces damaged or worn wiring to help eliminate intermittent operation or loss of function. What it does:

• Connects multiple electrical components through a single harness to ensure coordinated operation
• Replaces frayed, burnt, or broken wires and corroded terminals that cause intermittent or no power
• Restores proper signal paths for sensors, switches, motors or valves served by the harness
• Helps eliminate shorts, arcing, or erratic component behavior caused by damaged wiring

• One multi wiring harness as shown

• Disconnect all power (unplug appliance or shut off breaker) before starting any work
• Document or photo-mark connector locations before removal to ensure correct reassembly
• Route the harness following original clips and fasteners; avoid contact with sharp edges or hot surfaces
• If terminals or connectors are damaged, replace the entire harness rather than splicing unless specifically approved by manufacturer

Replacement nut that secures drawer and trim components on compatible LG appliances. It restores a firm, vibration-resistant fastening to help prevent loosening, rattling, or misalignment during normal use. What it does:

• Secures drawer, trim or small mounting brackets to the appliance chassis.
• Helps stop loosened fasteners that cause rattling or misaligned panels.
• Provides proper thread engagement for a stable connection.
• Matches the appliance's original fastening point when used as the listed part.

• Always disconnect power to the appliance before beginning any repair.
• Use the correct-size wrench or socket; avoid overtightening to prevent stripped threads.
• Inspect mating screw/bolt and threads for damage; replace damaged hardware as needed.

This is a small OEM washer used with the washer's internal mounting hardware to provide proper spacing and secure fasteners. It helps keep assemblies aligned and prevents hardware from loosening during operation. What it does:

• Acts as a spacer and load distributor for bolts or screws in the washer assembly
• Helps maintain proper alignment of panels or components
• Reduces wear between mating metal parts
• Can prevent fasteners from backing out due to vibration

• One washer as pictured

• Always unplug the appliance and shut off the water supply before servicing
• Access the mounting location per the service manual or parts diagram; replace only like-for-like
• Install with the correct orientation and hardware; do not overtighten fasteners
• If other fasteners or parts are corroded or worn, replace them at the same time

The Top Load Washer Coupling Assembly is an OEM component specifically designed for LG brand top-loading washing machines. This assembly connects the agitator shaft to the transmission inside the washer, allowing oscillating motions to be transferred through the transmission from the motor. 

Symptoms include:  

• No agitator movement or flickering motions during wash cycles
• Grinding or clicking noises coming from the motor/transmission area
• Leaks or loose fluid from damaged housing components  
• Shaking or instability of the entire washing machine

Causes of a bad coupling assembly can include material failure from ongoing vibration exposure, loosened connection points allowing unwanted play, or cracks/breaks due to heavy impacts.

A replacement clutch housing assembly that secures the clutch coupling to the washer drive—restores proper drive engagement and helps eliminate slipping, grinding, or failure to spin. Designed as a direct-fit service part for affected LG washers. What it does

• Houses and supports the clutch coupling that links the drive to the transmission.
• Restores reliable transfer of drive force so the tub can agitate and spin.
• Helps stop symptoms like slipping between cycles, unusual grinding or vibration, and failure to spin.
• Replaces worn, cracked, or damaged housings that can cause poor clutch engagement.

• One clutch housing assembly

• Disconnect power and water supply before beginning any repair.
• Access typically requires opening the washer cabinet or back panel; follow your model's service manual.
• Inspect related clutch and transmission components while accessible.

This thermistor assembly monitors water temperature inside the washer tub and relays a precise signal to the control board. Replacing a failed sensor restores accurate temperature sensing and helps prevent cycle errors and performance issues. What it does:

• Measures wash water temperature and sends the signal to the electronic control
• Enables the control to adjust cycle operation based on temperature feedback
• Common failure signs: tE/TE error codes on some models, incorrect temperatures, long cycles, or cycles that won't advance
• Intermittent faults may cause sporadic errors or inconsistent performance

• 1 thermistor assembly

• Disconnect power and shut off water before servicing
• Access location varies by model; the sensor is typically mounted in the outer tub or heater housing
• Unplug the harness, pull the old sensor straight out; seat the new sensor fully and reconnect the harness
• Route wiring away from moving parts; restore power and run a test cycle, checking for proper operation and any leaks around the sensor port

The Dispenser Assembly is an OEM part for LG washing machines. This part dispenses the appropriate amounts of detergent, fabric softener, or other laundry additives at the right time during the wash cycle.

Causes of a bad Dispenser Assembly can include clogging or buildup of residue, damage to the dispensing mechanisms or components, or issues with the electronic controls that regulate the dispensing process.

Symptoms of a bad washer Dispenser Assembly include:

• Improper dispensing of detergent or fabric softener
• Leaks or drips from the dispenser area
• The dispenser drawer not opening or closing properly
• Failure of the dispenser to dispense at the correct time during the cycle

This OEM LG part is also compatible with some Kenmore models.

This cover cap is a small plastic trim piece that restores a finished appearance and helps protect the underlying fastener or opening from dirt and debris. It's a simple cosmetic and protective replacement for worn or missing caps. What it does:

• Covers and protects exposed screws, fasteners or small openings on the appliance
• Prevents dirt, lint and moisture from entering vulnerable gaps
• Restores a clean, finished look to damaged or missing trim
• Common symptom: missing, cracked or loose cap that leaves a visible hole or exposed screw

• Disconnect power to the appliance before starting any repair
• Usually installs by snapping into place; may require removing an adjacent panel or fastener first
• Avoid excessive force to prevent breaking the plastic; use a plastic trim tool if needed

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.