Kenmore Washer 970.-C40052-00 (970-C40052-00, 970 -C40052-00) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W10135699
The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.
This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.
Do-It-Yourself Stories from Customers like You
Broken spider assembly; aka washer drum shaft assembly Jeff J. • Los Angeles , CA • November 01, 2015
I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point...
We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a...
Read more
More
$13.95
- Compare At:
-
$16.60
- You Save:
-
$2.65
Genuine Frigidaire part
By: Frigidaire
Part Number: 131763256
The Front Loading Washer Door Lock and Switch Assembly is an OEM part for Frigidaire washing machines. This component ensures that the washer door is securely locked during operation, preventing leaks and interruptions, and also communicates with the control board to allow the wash cycle to start.
Causes of a bad door lock and switch assembly can include wear and tear from regular use, damage from forced door opening, electrical failures within the locking mechanism, or issues with the switch contacts.
Symptoms of a bad door lock and switch assembly include:
- The washer door not locking or unlocking properly
- Error codes related to the door lock
- The washer not starting its cycle
- Interruptions in the wash cycle due to door lock failures
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
My washer would not complete the spin cycle and wring the water out of the clothes Lisa C. • Spring Lake , NC • March 12, 2014
I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely...
Read more
More
$113.95
- Compare At:
-
$136.74
- You Save:
-
$22.79
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304485917
The Shock Absorber Kit is an OEM part for Frigidaire washing machines. It is a comprehensive kit that includes 2 shock absorbers, 1 locking pin, 4 lock nuts, and a set of instructions. These shock absorbers play a vital role in reducing vibrations and absorbing shocks during the washing cycle, providing stability and minimizing excessive movement.
Causes of a bad shock absorber can include wear and tear over time, exposure to heavy loads or unbalanced loads that put excessive strain on the absorbers, or damage due to impact or mishandling.
Symptoms of a bad Shock Absorber include:
- Excessive shaking or vibrating during the wash cycle
- Loud banging noises
- The washer moving or walking during the operation
- Leaks due to increased stress on the tub and other components
This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
Do-It-Yourself Stories from Customers like You
Very noisy then ultimately bearing failure and a broken shock mount Brian B. • Canton , NY • September 23, 2014
I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the...
Read more
More
$46.95
- Compare At:
-
$55.87
- You Save:
-
$8.92
Genuine Frigidaire part
By: Frigidaire
Part Number: 137108000
The Drain Pump is an OEM part for Frigidaire washing machines. It's engineered to efficiently remove used water from the washer at the end of each wash cycle, playing a critical role in the appliance's ability to prepare for the next load.
Causes of a bad drain pump include blockages from small items or debris, mechanical failure due to wear and tear, or electrical issues preventing the pump from operating.
Symptoms of a bad Drain Pump include:
- Water not draining from the washer
- Unusual noises coming from the pump area, indicating a blockage or failure
- The washer not completing its cycle
- Error codes displayed on the washer related to draining issues
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Washing machine wasn't draining properly and the drain pump sounded loud and whiny Chris S. • Boulder , CO • March 30, 2014
Replace the drain pump after watching a video demonstrating the process. The washing machine had run properly and emptied, so I was surprised how much water remained in the pipe after disconnecting the old pump. Plan on having 2-3 large towels underneath before removing it.
The most difficult part (and most irritating) was replacing the intake and outtake hoses with the existing spring clamps. The drain hose into the pump took almost twenty minutes to attach properly. If the hardware store was...
Read more
More
$130.62
- Compare At:
-
$156.74
- You Save:
-
$26.12
Genuine Frigidaire part
By: Frigidaire
Part Number: 134051000
The Drum Drive Belt is an OEM part for Frigidaire dryers. It connects the drum to the motor, enabling the drum to rotate and tumble the clothes during drying cycles. The belt is 54 inches long and 5/8 inches wide
You should replace this drum drive belt if it becomes worn out, frayed, or broken due to the high heat and friction involved in the drying process. Additionally, improper loading or overloading of the dryer can cause the belt to stretch or snap.
Symptoms of a bad drum drive belt include:
- Dryer drum not turning
- A loud thumping or squealing noise during operation
- Dryer stopping mid-cycle
- Clothes remaining wet after the drying cycle
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Severe banging during spin cycle Vince V. • Benson , AZ • March 03, 2019
With more difficulty and frustration than expected but it works fine now.
Things learned:
1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture.
2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too.
3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the...
Read more
More
$21.95
- Compare At:
-
$30.17
- You Save:
-
$8.22
Genuine Frigidaire part
By: Frigidaire
Part Number: 134190200
The Water Inlet Valve Assembly is an OEM part for Frigidaire washing machines. This assembly controls the flow of water into the washing machine during the fill cycles, ensuring the correct amount of water enters the tub.
Over time, the water inlet valve can become faulty due to mineral buildup, wear and tear from frequent use, or damage to the valve components. If the valve is not functioning properly, it can result in issues with the water flow into your washing machine.
Symptoms of a bad water inlet valve assembly include:
- No water entering the washing machine
- The washer filling slowly or not at all
- The washing machine filling with water when it is turned off
- Leaks from the valve area
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
This part fixes the following symptoms
-
No hot or cold water
-
Will not stop filling with water
-
Will not fill with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
The washer was filling very slow especially cold water. Wayne S. • Oakland , MD • February 10, 2023
This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent...
Read more
More
$100.95
- Compare At:
-
$120.13
- You Save:
-
$19.18
Genuine Frigidaire part
By: Frigidaire
Part Number: 134144700
The Suspension Spring Kit is an OEM replacement part for Frigidaire front-loading washing machines. These suspension springs are positioned at the top front of the washer, underneath the tub, to help support the weight of the drum during operation.
Over many cleaning cycles, suspension springs can wear down and lose their ability to dampen vibration.
Symptoms of bad suspension springs include:
- Excessive shaking or rattling of the washing machine
- Loud banging or knocking noises coming from inside the washer
- The tub moving excessively during washing and spinning
It is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Not spinning heavy loads. Jim S. • Midlothian , TX • December 05, 2017
Replaced springs and shocks.
Read more
More
$49.95
- Compare At:
-
$59.44
- You Save:
-
$9.49
Genuine Frigidaire part
By: Frigidaire
Part Number: 131268300
The Shock Absorber Mounting Pin is an OEM part for Frigidaire washing machines. It is a part that secures the shock absorber in place, ensuring proper absorption of vibrations and shocks during the washing cycle.
Causes of a bad shock absorber mounting pin can include loosening over time due to constant movement and vibrations, accidental damage or loss during repair or maintenance, or general wear and tear.
Symptoms of a bad or missing shock absorber mounting pin include:
- Excessive shaking or vibrating during the wash cycle
- Loud banging or rattling noises
- The washer moving or "walking" across the floor
- Premature wear or damage to the shock absorbers and other components
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Severe banging during spin cycle Vince V. • Benson , AZ • March 03, 2019
With more difficulty and frustration than expected but it works fine now.
Things learned:
1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture.
2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too.
3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the...
Read more
More
$16.95
- Compare At:
-
$20.00
- You Save:
-
$3.05
Genuine Frigidaire part
By: Frigidaire
Part Number: 131168200
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
- Fastens components to frames, brackets, and covers
- Replaces missing, damaged, or rusted screws
- Helps reduce looseness, vibration, and rattling noises
- Restores proper alignment of panels and assemblies
What's included: One screw
- Disconnect power before servicing; shut off gas/water if applicable
- Start the screw by hand to avoid cross-threading; use the proper driver
- Tighten snugly—do not overtighten to prevent stripping metal or plastic
Do-It-Yourself Stories from Customers like You
Grill on air duct had an item melt on to it and partially block air flow Charles C. • Orchard Park , NY • November 25, 2017
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube.
I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to...
Read more
More
$19.95
- Compare At:
-
$23.94
- You Save:
-
$3.99
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303937187
The Door Boot Kit is an OEM part for Frigidaire washing machines. Also known as the door gasket or door seal, is located around the opening of the washing machine. It prevents water from leaking out during the wash cycle and maintains a secure seal when the door is closed.
Causes of a faulty door boot can include regular wear and tear, physical damage, or mold and mildew buildup. These factors can result in issues such as water leakage from the door, visible tears or cracks in the boot, or unpleasant odors from mold growth.
Symptoms of a bad door boot may include:
- Water leaking from the door during the wash cycle
- Visible tears, cracks, or deformations on the boot
- Foul odors emanating from the washing machine
This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
Do-It-Yourself Stories from Customers like You
There was a strong smell of mold coming from the door boot. Thomas H. • Netcong , NJ • June 12, 2022
I replaced the door boot with a new one from AppliancePartsPros.com. The most difficult part was starting at the back end of the new boot onto the stationary rim, just in front of the tub. And then anchoring it in place with the existing spring from the previous boot. To start the boot I had to hook the top edge of the boot, where the arrow tab is, onto the rectangular projection on the tub rim and then roll the rubber boot edge down around the tub rim and hope the rim was going into the...
Read more
More
$104.74
- Compare At:
-
$125.69
- You Save:
-
$20.95
Genuine Frigidaire part
By: Frigidaire
Part Number: 131784700
The Sump Hose is an OEM part for Frigidaire washing machines. This hose carries water from the tub to the pump, ensuring proper drainage during the wash and spin cycles.
Causes of a bad sump hose can include regular wear and tear, cracks or holes from aging, and clogs from debris buildup.
Symptoms of a bad sump hose include:
- Water leaking from the bottom of the washing machine
- Slow or incomplete drainage
- Visible cracks or holes in the hose
- The washing machine stopping mid-cycle due to drainage issues
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Water remained in the tub on my front load washer. Peter Y. • Alameda , CA • November 13, 2017
I changed the pump and also discovered the coin trap was wearing thin because it was rubbing against the sheet metal. So I replaced that as well.
It took about 15 minutes to remove the coin trap and pump and about 20 minutes to install.
The shipping was amazingly fast. I received the parts the next morning. I'm talking I ordered the parts before noon, chose the "fast shipping" option and received parts the next morning around 8:30 AM.
Read more
More
$79.95
- Compare At:
-
$95.14
- You Save:
-
$15.19
Genuine Frigidaire part
By: Frigidaire
Part Number: 131302800
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
- Fastens the drum baffle/lifter (vane) to the rotating drum
- Helps maintain proper tumble and load turnover
- Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
- Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes
What's included: One screw
- Disconnect power before servicing; shut off gas
- Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
- Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
- Start all screws before final tightening to seat the baffle evenly
Do-It-Yourself Stories from Customers like You
The pump hose had a tear in it and the water hoses were in bad shape Steven V. • El Cerrito , CA • September 21, 2014
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy
Read more
More
$17.95
- Compare At:
-
$21.54
- You Save:
-
$3.59
Genuine Frigidaire part
By: Frigidaire
Part Number: 134146100
The Gasket is an OEM part for Frigidaire washing machines. This part is located between the front and rear outer tubs and prevents water leaks by maintaining a watertight seal between them. The gasket acts as a barrier to ensure that water used during the washing process remains contained within the inner tub, preventing it from seeping into the washing machine's surrounding components.
Causes of a bad gasket can include regular wear and tear, exposure to harsh detergents, or deterioration over time.
Symptoms of a bad gasket include:
- Water leaking from the outer tub area
- Visible cracks or deterioration in the gasket material
- The washing machine not holding water properly
- Increased noise or vibration during operation
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Very noisy then ultimately bearing failure and a broken shock mount Brian B. • Canton , NY • September 23, 2014
I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the...
Read more
More
$51.95
- Compare At:
-
$61.82
- You Save:
-
$9.87
Genuine Frigidaire part
By: Frigidaire
Part Number: 134737300
This clamp secures a hose to its fitting, maintaining a tight, leak-resistant seal at the connection. Replace a fatigued or missing clamp to help prevent drips and stop hoses from working loose under vibration.
- Holds a hose firmly on a pump, tub, dispenser, or valve outlet
- Maintains clamping force to help minimize leaks at the joint
- Helps keep hoses from slipping off during operation
- Common signs: water at a hose joint, loose/slipping hose, damaged or corroded clamp
What's included: 1 clamp Install notes:
- Disconnect power and shut off water supply before servicing
- Place a towel or pan to catch residual water at the connection
- Note hose position; remove the old clamp, seat hose fully on the fitting, position the new clamp over the bead, and secure
- After reassembly, run a short cycle and check for leaks
Do-It-Yourself Stories from Customers like You
Leaking hose. Sherry W. • Auburndale , FL • December 02, 2017
New hose and clamp.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Frigidaire part
By: Frigidaire
Part Number: 131274600
This tub baffle is the vane inside the washer drum that lifts and tumbles laundry. Replacing a cracked or missing baffle restores proper turnover, helps prevent fabric snags, and reduces banging from loose parts.
- Lifts and moves clothes through the wash and rinse for effective cleaning
- Promotes more even tumbling and extraction during spin
- Replace if the baffle is cracked, loose, or missing
- Common symptoms: poor tumbling, items snagging or tearing, rattling/thumping inside the drum
What's included: One tub baffle Install notes:
- Disconnect power and turn off water supply before servicing
- Open the door and rotate the drum to access the baffle fasteners from inside the drum
- Remove screws or release locking tabs, seat the new baffle fully, and secure with existing hardware
- Hand-rotate the drum to confirm clearance before running a cycle
Do-It-Yourself Stories from Customers like You
Broken plastic vanes Ronald M. • No. Tonawanda , NY • March 13, 2015
Three new vanes. Installation was easy, removed one stainless screw on each vane, slid the broken vanes toward the front of the machine, compressed the old vane slightly and came right out. They have to be slid about 1 to 2 inches forward for removal. This was an easy fix.
Read more
More
$54.26
- Compare At:
-
$64.57
- You Save:
-
$10.31
Genuine Frigidaire part
By: Frigidaire
Part Number: 131205300
This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.
- Fastens cabinet panels, brackets, or internal parts in washers and dryers
- Direct replacement for worn or lost screws to keep assemblies aligned and secure
- Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
- Spec: #10-16 thread; 0.75-inch length
What's included: 1 screw (10-16 x 0.75 in) Install notes:
- Disconnect power; for washers, also shut off water supply
- Match the original screw location; start threads by hand to prevent cross-threading
- Use a driver that fits the screw head properly; tighten snugly without overtightening
Do-It-Yourself Stories from Customers like You
Door hinge was wore out. Jerry K. • North. Judson , IN • November 19, 2018
Like the original.
Read more
More
$8.95
- Compare At:
-
$10.74
- You Save:
-
$1.79