Kenmore Refrigerator 106.51264104 (10651264104, 106 51264104) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2196195
The Dispenser Door Pin Kit is an OEM part for Whirlpool refrigerators. This kit includes the pins that secure the dispenser door, allowing it to open and close smoothly when dispensing ice or water.
Causes of a bad dispenser door pin kit can include normal wear and tear, breakage from frequent use, or damage due to mishandling.
Symptoms of a bad dispenser door pin kit include:
- The dispenser door not opening or closing properly
- Leaks or drips from the dispenser area
- Loose or misaligned dispenser door
- Difficulty in dispensing ice or water
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Broken tab on ice door Jeffery J. • Mustang , OK • December 19, 2015
It was not looking good. I could not order the part I needed as it was part of the door - eve though it had screws att Hong it to the freezer door. At one web site it was a replacement of the whole freezer door!/? Luckily I ventured further and found this repair kit and video instructions. My order arrived in 3 days, and the install (thanks to the video) was easy. A whole lot better than buying a new freezer door - not!
BTW - Whitlpool should not have made the tabs out of plastic, the metal...
Read more
More
$8.57
- Compare At:
-
$10.20
- You Save:
-
$1.63
Genuine Whirlpool part
By: Whirlpool
Part Number: W11223328
This shelf support stud anchors a refrigerator shelf to the cabinet liner so it stays level and secure. Replace a cracked or missing stud to restore proper support and prevent shelves from tilting, slipping, or dropping.
- Locks into the liner wall to provide a mounting point for the shelf frame or bracket
- Keeps the shelf aligned and at the correct height
- Common symptoms: broken/missing stud, shelf won't sit flat, shelf sags or falls on one side
- Helps prevent items from sliding due to an unstable shelf
What's included: One shelf support stud Install notes:
- Disconnect power; remove the shelf and any items resting on it. Handle glass shelves carefully and consider wearing cut-resistant gloves.
- Remove the damaged stud (release the locking tab or twist out, depending on design).
- Insert the new stud into the existing hole until fully seated and locked.
- Reinstall the shelf and verify it sits level before reloading.
Do-It-Yourself Stories from Customers like You
Broken shelf and drawer. Regina M. • Yardley , PA • November 10, 2017
Myself
Read more
More
$15.95
- Compare At:
-
$18.98
- You Save:
-
$3.03
Genuine Whirlpool part
By: Whirlpool
Part Number: 2159080
Color: Black
Do-It-Yourself Stories from Customers like You
Worn out freezer gasket Jeffrey T. • Norfolk , VA • February 18, 2020
Bought gasket from website, followed easy helpful video instructions, perfect fit.
Read more
More
$148.50
- Compare At:
-
$178.20
- You Save:
-
$29.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10152858
Color: White
Do-It-Yourself Stories from Customers like You
The ice dispenser lever was cracked and did no longer trigger the dispensing of the ice Andrea M. • Honolulu , HI • March 01, 2015
I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better.
I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some...
Read more
More
$53.33
- Compare At:
-
$64.00
- You Save:
-
$10.67
Genuine Whirlpool part
By: Whirlpool
Part Number: W11496481
The Water Tube is an OEM component specifically designed for Whirlpool refrigerators. This 1/4" diameter water tube provides a pathway for water to flow through the refrigerator's internal components during operations like ice production.
Causes of a bad water tube can include cracks or defects from manufacturing, damage from impact or abrasion during shipping or installation, or wear over time from cycles of use.
Symptoms of a bad water tube include:
- Water leaks or drips inside the refrigerator
- Insufficient or slow water flow to components
- Abnormal sounds from water not flowing smoothly
- Failure of components dependent on water flow like the ice maker
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore refrigerator models.
Do-It-Yourself Stories from Customers like You
Water filter housing leaking H M. • Picayune , MS • August 18, 2015
Replaced filter housing, and both water tubes
Read more
More
$26.95
- Compare At:
-
$31.80
- You Save:
-
$4.85
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2198661
This top coupling links two drive components in select washers to transfer rotation smoothly. Replacing a worn or stripped coupling restores consistent agitation/spin and can reduce slipping, rattling, or grinding noises from the drive area. What it does:
- Connects mating shafts/components so power is transmitted through the drive system
- Helps maintain alignment and cushions minor shock to protect other parts
- Failure symptoms may include no or weak agitation/spin, intermittent drive, or clicking/grinding sounds
- Visual clues can include cracks, rounded/stripped splines, or excessive play
What's included:
Install notes:
- Disconnect power; turn off water supply if moving the appliance
- Access location varies by model; cabinet/top or front panel removal may be required
- Note orientation of flats/splines and seat the coupling fully—do not hammer into place
- Inspect the mating hub/shaft; replace worn companion parts to prevent rapid re-wear
Do-It-Yourself Stories from Customers like You
Broken drive on door dispenser for ice maker Richard H. • Bartlett , TN • March 07, 2016
My LG electric dryer stopped drying the other day and I searched on line for suggestions on what may have caused it to stop working. I came across AppliancePartsPros.com and quickly found some of the most common issues with my LG dryer. The problems were listed in the order of most common occurrence, and had extremely helpful and detailed instructions on how to not only diagnose the problem, they also showed exactly how to access and repair the issue. Unfortunately, it was late on a Thursday...
Read more
More
$7.95
- Compare At:
-
$9.46
- You Save:
-
$1.51
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10224328
For the complete ice door kit order W10823377.
Do-It-Yourself Stories from Customers like You
Ice dispenser chute door was not closing or sealing Robert H. • West Palm Bch , FL • July 23, 2025
The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable...
Read more
More
$48.95
- Compare At:
-
$57.76
- You Save:
-
$8.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3196175
Size: 8-18 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Oven drawer wouldn’t slide properly. Nick B. • Hanover , MD • November 09, 2020
Whenever the drawer was opened, it would fall of the guide rails. This lead to the drawer being crooked several times. I took the drawer out and noticed one of the glides was missing. Ordered a new pair, popped it on and now the drawer slides properly.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2203771
The Top Hinge is an OEM part for Whirlpool refrigerators. This hinge ensures the proper alignment and smooth operation of the refrigerator door, allowing it to open and close securely. It supports the weight of the door and helps maintain an airtight seal.
Causes of a bad top hinge can include general wear and tear, heavy use, or accidental damage.
Symptoms of a bad top hinge include:
- Refrigerator door sagging or misaligned
- Difficulty in opening or closing the door
- Door not sealing properly, leading to temperature fluctuations
- Unusual noises when the door is operated
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Needed hinges for doors William H. • Niles , MI • September 22, 2015
Put the new hinges on the doors fyi you need to tell what size the screws are for the hinge kits would help a lot
Read more
More
$51.26
- Compare At:
-
$61.00
- You Save:
-
$9.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2186494T
Color: biscuit. It measures about 2-1/2 inches in diameter. For black order WP2186494B. For white order WP2186494W.
Do-It-Yourself Stories from Customers like You
Water leak from water filter housing John B. • Weeki Wachee , FL • January 19, 2019
Replaced with new one and followed the instruction from the video that is on the order
Read more
More
$11.40
- Compare At:
-
$13.68
- You Save:
-
$2.28
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2206671B
Color: black. Measures about 9 inches wide by 2-1/2 inches deep.
Do-It-Yourself Stories from Customers like You
Stopped dispensing water Cristopher C. • Santa Rosa , CA • July 15, 2016
Ordered the parts. Watched a great video on this web site. Installed. Fixed. Easy peesey.
Read more
More
$55.38
- Compare At:
-
$65.35
- You Save:
-
$9.97
Genuine Whirlpool part
By: Whirlpool
Part Number: W11233072
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
- Fastens panels, brackets, covers, or internal parts to the chassis or frame
- Helps maintain alignment and support, reducing rattle, vibration, or looseness
- Replaces missing or damaged screws that have backed out, broken, or stripped
- Restores secure mounting after service when original hardware is lost
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supplies before servicing
- Use the correct driver; start threads by hand to avoid cross-threading
- Match length and thread to the original location; do not substitute with longer hardware
- Tighten snugly; do not overtighten into plastic or thin metal
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2198608
The Whirlpool latch spring is an OEM replacement part responsible for securing the ice container or bin in place on a refrigerator. Its main function is to provide tension and support to the ice container latch, allowing it to engage and disengage properly. When the ice container is inserted into the refrigerator's ice compartment, the latch spring ensures that it securely locks in place, preventing accidental spillage of ice.
Causes of a bad latch spring can include metal fatigue from repeated use, rust or corrosion from exposure to moisture, or physical damage from accidental impacts.
Symptoms of a bad latch spring include:
- The ice container not staying in place and sliding out of position
- Difficulty in properly attaching or detaching the ice container from the refrigerator
- The ice container feeling loose or wobbly when inside the ice compartment
- The ice container not aligning correctly with the ice dispenser or auger
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Ice will not dispense from door John J. • Scottsdale , AZ • December 29, 2019
I replaced the driveshaft and the latch on the ice bin as well as the washer that prevents moisture and water from getting down the driveshaft and into the motor. It was an easy job, especially with the video.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489478
Size: 8 x 1/2 ab.
Do-It-Yourself Stories from Customers like You
Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W10181323
This condenser fan motor spins the fan that moves air across the condenser coils and around the compressor. Replacing a weak or seized motor restores proper heat removal so the cooling system can maintain stable temperatures and run efficiently.
- Drives the condenser fan to move airflow through the condenser section
- Helps dissipate heat from the refrigeration system and cool the compressor
- Failure may present as the condenser fan not running
- May also cause warm temperatures, longer run times, or loud scraping/whirring noises near the rear or bottom of the unit
- Can contribute to the compressor running hot
What's included: 1 condenser fan motor Install notes:
- Disconnect power before servicing; use gloves to protect from sharp edges
- Access the condenser area; install the new motor in the same orientation as the original
- Transfer the existing fan blade, bracket, and grommets if required; keep wiring clear of the blade
- Restore power and verify fan operation with the system running
Do-It-Yourself Stories from Customers like You
The outside of my frigidare refrigerator felt hot near the door gasket on both side of the freezer Trent S. • Bethlehem , PA • May 27, 2014
I found several "threads" on my google search which indicated that it might be caused by a non-functional condenser fan. I removed the back bottom panel and voila, the fan was not spinning even though the compressor was running and felt very hot. If I spun the blades, the fan would run, but as soon as the compressor shut off, it would not start up again without my help. The replacement part was easy to find at AppliancePartsPros.com. I ordered it and had it within 48 hours. I didn't even need...
Read more
More
$170.95
- Compare At:
-
$203.43
- You Save:
-
$32.48
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2323197
This defrost heater warms the evaporator during automatic defrost to melt built-up frost so air can move freely and temperatures stay consistent. Replace a failed heater to restore normal cooling and end recurring frost on the freezer panel.
- Melts ice from the evaporator coil during the defrost cycle
- Prevents frost buildup that restricts airflow and causes warm spots
- Helps maintain stable refrigerator and freezer temperatures
- Typical failure signs: heavy frost on the back wall, reduced cooling, fan noise from ice contact, frequent manual defrosting
Includes: 1 defrost heater
- Disconnect power before servicing; wear cut-resistant gloves
- Access through the freezer compartment; remove shelves/ice bin and rear panel to reach the evaporator
- Match wire connections and route leads exactly as original; keep wiring clear of the fan and sharp edges
- After reassembly, restore power and monitor a defrost cycle; if frost quickly returns, also evaluate the defrost thermostat and control
Do-It-Yourself Stories from Customers like You
Circuit breaker would reset once refrigerator goes into defrost mode John C. • Elk Grove , CA • November 16, 2016
Replaced defrost heater with the help of the appliance parts pro how to video.
Video had made doing the job with ease. Had a laptop next to me making sure I had not missed a step. Been a week and things been all good. Well worth it. Thank you!
Read more
More
$61.75
- Compare At:
-
$74.10
- You Save:
-
$12.35