Kenmore Washer 110.20956991 (11020956991, 110 20956991) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8572720
Fix a washer that hums but won't spin or agitate with this motor start capacitor. Repairs motor startup issues. Moderate DIY, 30-60 minutes.
Do-It-Yourself Stories from Customers like You
You could here the motor try to start but nthen just hum John H. • Brockton , MA • September 10, 2015
Found the motor switch was fried. So replaced that and the capacitor. Starts fine now.
Read more
More
$60.52
- Compare At:
-
$72.02
- You Save:
-
$11.50
Genuine Whirlpool part
By: Whirlpool
Part Number: WP388326
This console screw secures the control console to the appliance cabinet or top, keeping the panel tight and aligned. Replace a missing or damaged screw to stop panel wobble and rattling and maintain a snug, stable fit. What it does:
- Fastens the control console/control panel to the cabinet or top panel
- Helps maintain alignment and reduces vibration and rattling
- Replaces a missing, stripped, or rusty original screw
- Common fix for a loose or lifting console/panel
What's included:
Install notes:
- Disconnect power before service; if applicable, shut off gas/water
- Support the console to avoid straining wiring harnesses
- Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
- Use the correct driver style for your model's hardware
Do-It-Yourself Stories from Customers like You
Leaking water from the tub seal David C. • Bessemer City , NC • January 27, 2018
THIE REPAIR WAS ON A WHIRLPOOL TOP LOAD WASHING MACHINE
At first I suspected the leak was from the pump because I had replaced the pump 2 times over 10 years. This time with the cabinet removed and filling the tub with water, I saw water running down one of the steel support arms that go under the tub, so I was guessing that it was coming from the tub seal. I had to use a jumper wire to bypass the Lid Switch so the water would drain.
Several months before I had this issue with the water leaking...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62780
Used to lock washer cabinet to rear wall of washer.
Do-It-Yourself Stories from Customers like You
Washing machine wouldn't spin Alyne K. • Kaunakakai , HI • May 01, 2015
After looking at several YouTube videos, we decided we could attempt to fix this ourselves. We found the easiest video to follow from Appliance Parts, and ordered the clips and lid switch assembly (the clips we had to replace because we goofed that one ourselves). The parts came within a couple of days. The repair took a little over 1/2 hour only because we had to re-do some steps because my husband was over anxious and did some things without reviewing the video. Overall, it was a very...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3354845
Loud rattling or loose agitator during wash? This clip secures the agitator assembly to eliminate noise and restore proper back-and-forth motion. Quick DIY fix.
Do-It-Yourself Stories from Customers like You
The washer was exceptionally loud during agitation cycle. Matt B. • Rio Rancho , NM • July 01, 2022
Found that by manually spinning agitator one direction it seemed free, but spinning counterclockwise it seemed to stick a little. Pulled dispenser and agitator and found the agitator washer hole was oval rather than round. Replaced the agitator washer and the washer seems to sound normally for now. Not sure if the new agitator washer will eventually grind down due to non-circular action from the transmission, or if the agitator and clip will keep the transmission centered long term. Should...
Read more
More
$15.95
- Compare At:
-
$18.98
- You Save:
-
$3.03
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21258
The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$11.95
- Compare At:
-
$13.33
- You Save:
-
$1.38
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3946532
Washer motor shield deflects water, lint, and debris away from the drive motor. Replace if cracked or missing to prevent motor damage. Simple install.
More
$20.49
- Compare At:
-
$24.18
- You Save:
-
$3.69
Genuine Whirlpool part
By: Whirlpool
Part Number: WP89503
Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.
Do-It-Yourself Stories from Customers like You
Low water flow and fabric softener would dispense immediately when cycle started Bob G. • Sylacauga , AL • January 19, 2019
Replaced flow meter and control valve
Read more
More
$19.31
- Compare At:
-
$22.79
- You Save:
-
$3.48
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62750
The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.
Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.
Symptoms of a bad spacer include:
- Misalignment of components
- Unusual noises during operation
- Difficulty in assembling or disassembling parts
- Reduced efficiency of the appliance
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Sold individually, four are needed to replace all parts. Screw part number WP3390631.
More
$9.63
- Compare At:
-
$11.46
- You Save:
-
$1.83
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8519200
Structural bracket that secures the rear panel to the washer chassis. Replace if cracked, broken, or missing to restore proper alignment and cabinet stability.
Do-It-Yourself Stories from Customers like You
No spin/agitate. Daniel S. • Landenberg , PA • November 11, 2022
In the end, with a new coupler. But I relearned old lessons the hard way.
The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned...
Read more
More
$18.23
- Compare At:
-
$21.69
- You Save:
-
$3.46
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3359452
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Do-It-Yourself Stories from Customers like You
Whirlpool washer was shaking and moving in spin cycle Charles B. • Sioux Falls , SD • September 25, 2018
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3390631
10 - 16 x 1/2
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8054980
This lid switch is the washer's safety interlock. It detects when the lid is closed so the machine can agitate and spin, and cuts power when the lid is opened to stop operation and enhance user safety.
- Monitors lid position and allows agitation/spin only when the lid is closed
- Interrupts motor operation if the lid opens during a cycle
- Common failure symptoms: washer won't start or spin, fills but stalls, stops intermittently, or displays "lid open" alerts
- Restores proper cycle progression and safety shutoff when replaced
What's included: One lid switch Install notes:
- Disconnect power and water supply before servicing
- Access the switch from under the top panel/console per your model's procedure
- Release the old switch, move the harness to the new switch, and secure wiring away from moving parts
- Ensure the lid closes and actuates the switch before reassembly and test run
Do-It-Yourself Stories from Customers like You
Direct drive motor coupling failed wouldn't agitate or spin Tim H. • Fort Collins , CO • October 18, 2014
Was set to pull the trigger on a new washer since this one was 10+ years old. Broke a $25 lid switch fumbling to get the washer open before I found the appliancepros video library. Once I got things apart the right way I was able to diagnose the problem in 5 minutes. Identified the $10 part needed. Got the $10 coupling and the $25 switch and had the washer working like new in 20 minutes. I'm pretty proud of myself.. not going to tell anyone about the $25 switch.
Read more
More
$115.49
- Compare At:
-
$137.43
- You Save:
-
$21.94
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62691
Rubber grommet for motor mount stud.
Do-It-Yourself Stories from Customers like You
Washer did not agitate Gary S. • Kimberling City , MO • December 26, 2016
Replaced dog ears.
Read more
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: W10389328
Inner tub basket holds clothing during wash cycles. Replace if cracked, rusty, or broken. Installs in center of washer between outer tub and agitator.
Do-It-Yourself Stories from Customers like You
Replacement of rusty inner basket Michael K. • Paramus , NJ • April 18, 2015
Ordered the parts from AppliancePartsPros - super fast shipping, and even though I opted for regular shipping all of my parts arrived the very next day, including the big and bulky inner basket. Disassembly went smoothly, simply following the directions in the AppliancePartsPros video. The only problem I had was that the inner basket simply would NOT come of the drive block no matter what I did. Struggled for a few hours trying to take it off. Then, I called AppliancePartsPros and they said it...
Read more
More
$297.64
- Compare At:
-
$337.09
- You Save:
-
$39.45
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8578209
Fixes poor cleaning or clothes not moving during wash cycle. This agitator restores proper wash action by rotating and lifting laundry through water. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Agitator was broke Daniel P. • Madison , OH • August 09, 2016
Striped the agitator out and replaced the bottom portion of agitator.
What was amazing was I placed the order Friday at 5 pm. It arrived Saturday at7:30pm.
Read more
More
$103.33
- Compare At:
-
$124.00
- You Save:
-
$20.67
Genuine Whirlpool part
By: Whirlpool
Part Number: W10820044
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Do-It-Yourself Stories from Customers like You
Power cord got pinched and shorted out Gary D. • Kentwood , MI • July 27, 2014
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops.
Read more
More
$80.95
- Compare At:
-
$97.14
- You Save:
-
$16.19