Kenmore Washer 110.22722100 (11022722100, 110 22722100) Parts

I first checked to make sure the washer was level. The washer is on a concrete floor. After watching lots of you tube videos I ordered all the parts that could be causing this problem. I ordered: Balance Ring, Suspension Pad Kit (3 rectangle plastic wear pads), Tub Suspension Pads(3 curved plastic wear pads), Suspension Spring, and a Spanner Wrench tool. After getting the washer apart it was obvious that the problem was the Tub Suspension Pads they had completely worn away so that only the... Read more

I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new... Read more

I just replaced the glass lid and broken plastic frame with the all metal one. Call 877 477 7278 for appliancepartspros and order the following Whirlpool parts (prices as of November 2016): 1 lid part number WP8572026 (AP6013408) for $119.81 2 hinges WP8563964 (AP6004844) for $6.17 each 4 screws WPW10119828 (AP6015313) for $1.97 each Total $140.03 plus $8.95 shipping, grand total $148.98 Note that it does not say that this lid will fit model 7800, but the lid will fit this model. The... Read more

Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly. Now we're washing again and no leaks! Read more

• Will not stop filling with water
• Will not fill with water

At first, I thought, maybe I should just get a new washing machine. After all, it is almost 20 years old! I couldn't bring myself to do that and said to myself, let me see if I can figure out what parts I need and see if I can find a video that tells me how to do it and see how hard it is. I’ve never attempted appliance repair before. After figuring out what the most likely parts were, I ordered the water level switch and agitator cam repair kit - I figured for $10 more, I might as well... Read more

Found the motor switch was fried. So replaced that and the capacitor. Starts fine now. Read more

THIE REPAIR WAS ON A WHIRLPOOL TOP LOAD WASHING MACHINE At first I suspected the leak was from the pump because I had replaced the pump 2 times over 10 years. This time with the cabinet removed and filling the tub with water, I saw water running down one of the steel support arms that go under the tub, so I was guessing that it was coming from the tub seal. I had to use a jumper wire to bypass the Lid Switch so the water would drain. Several months before I had this issue with the water leaking... Read more

Replaced springs and the ordered clips holding the control panel to the washer outer cabinet. Clips had been elongated from earlier repair work. A DIY tutorial was a great help. Read more

I started by replacing the lid switch without the desired result. So I decided to replace the timer unit. It works like a new machine at the moment. At least on the first trial load. More loads will convince me that it is fixed for sure. I cannot be more complimentary about Appliance Parts Pros as I live very remotely in West Texas. The part arrived quickly and it was the exact right part required as ordered. This is my second order and I will return for more parts if I need them. Read more

Found that by manually spinning agitator one direction it seemed free, but spinning counterclockwise it seemed to stick a little. Pulled dispenser and agitator and found the agitator washer hole was oval rather than round. Replaced the agitator washer and the washer seems to sound normally for now. Not sure if the new agitator washer will eventually grind down due to non-circular action from the transmission, or if the agitator and clip will keep the transmission centered long term. Should... Read more

Replaced both with ease after reviewing video. Parts matched OEM specs perfectly. ***Shipping time was excellent - placed order with standard package delivery at @11pm on a Tuesday evening & received the order in Southeast Texas Thursday morning @11am. Read more

With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more

In the end, with a new coupler. But I relearned old lessons the hard way. The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned... Read more

Replaced flow meter and control valve Read more