Kenmore Washer 110.28002011 (11028002011, 110 28002011) Parts

Removed valve and replaced with new one. Read more

Touch up paint Read more

Replaced It With New One Read more

I had to cut the old agitator out with an oscillating saw in order to access the agitator drive. This is the second Maytag (MVWC 565) I have had to do this to. I first tried removing it by sliding straps under the agitator then then using a jack to pull it loose which did not work either time. One suggestion I have would be to remove debris from tub as you cut in order to prevent it from dropping from the inner tub into the outer tub. Read more

I had previously replaced the transmission in my two year old Whirlpool Cabrio washing machine. Overall it was in good shape but gets heavy use. That repair was approximately $200 and worked for several months. Recently it began leaking. At first I thought it was the tub-to-shaft seal. I replaced this part but it was still leaking. It turns out it was the simplest of things... The drain hose was not connected very well! I replaced the drain hose ($11 part) and while I was at it I... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• Leaking

We ordered parts from appliance parts pros and I fixed it. Read more

My Mom's Kenmore had a burnt plastic smell after a thunderstorm. Found motor capacitor had melted through, dumping liquid platic "spaghetti" onto the insulation blanket under the washer. All other compents looked fine. Told her not to use it until I replaced capacitor. The washer is 4 yrs old but the new capacitor revision was 3 letters higher, so they've made some design changes. Externally it looks the same. There is a large number on the capacitor, but the part is ordered by the much... Read more

There was a horrible screeching noise coming from the washer, and upon inspection I found that the retaining nut that attaches the cam to the machine was either improperly tightened to begin with or had worked itself loose causing the cam to wobble and the belt to work down the cam. The cam gear teeth became worn and the belt worked itself half off the cam and cut a hole in the protective plastic screen containing the whole ensemble. I purchased the belt, shield and cam kit. The parts are... Read more

• Leaking

Took off cover, installed new parts. Read more

Put in new lid lock. This is my second one in 1 year. Whirlpool suggested I leave it loose so that if somebody did try and force it open, it wouldn't break it. This lid lock has 4 wires and cannot be bypassed. Read more

I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new... Read more

I just replaced the glass lid and broken plastic frame with the all metal one. Call 877 477 7278 for appliancepartspros and order the following Whirlpool parts (prices as of November 2016): 1 lid part number WP8572026 (AP6013408) for $119.81 2 hinges WP8563964 (AP6004844) for $6.17 each 4 screws WPW10119828 (AP6015313) for $1.97 each Total $140.03 plus $8.95 shipping, grand total $148.98 Note that it does not say that this lid will fit model 7800, but the lid will fit this model. The... Read more

I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new... Read more

Found AppliancePartsPros on-line. Sent us the manual, parts list, etc. via .pdf files. Our local guy did not. Had parts in stock, two day shipping, totally painless. The parts were approximately 1/2 the price the local guy wanted. OEM parts. Perfect fit on replacement. The Whirlpool is so well made, it was very easy to repair. It has several items, over the years, which failed. In all cases, repair was painless with a few common hand tools and a tad of patience. AppliancePartsPros had... Read more

Symptoms: Machine was spinning and spitting a dark colored oil in a circular pattern on the floor under the machine. No strange noises, just messy. Researched issue, Gear-case bad, seal deteriorated and not preventing water from entering gear-case. The additional cam, belt etc I had replaced due to the amount of oil and transmission residue attached to them. Ordered parts, EVERYTHING parts-wise that is needed is included in gear-case package. **NOTE: You WILL need to get a whirlpool spanner... Read more