Kenmore Refrigerator 363.9562582 (3639562582, 363 9562582) Parts
Genuine Ge part
By: Ge
Part Number: 40A15
The Light Bulb (40W) is an OEM component for GE refrigerators. As an essential task lamp, it illuminates the interior of the refrigerator and freezer compartments.
All light bulbs will eventually burn out with consistent use over many years. Vibration during compressor cycles can also potentially disrupt bulb filaments faster.
Symptoms of a burnt out refrigerator light bulb include:
- Dim or no light illuminating inside refrigerator shelves
- Shadows and dark spots making it difficult to find items
- Higher utility costs from leaving the door open to see inside
This bulb is also compatible with refrigerators from brands like Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Nothing worked except the light :) Przemyslaw B. • Wallington , NJ • September 20, 2014
I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks
Read more
More
$18.95
- Compare At:
-
$22.36
- You Save:
-
$3.41
Genuine Ge part
By: Ge
Part Number: WR60X187
The Condenser Fan Motor is an OEM part for GE refrigerators. It is designed to circulate air through the condenser coils, helping to dissipate heat and keep the refrigerator's internal components cool. This ensures efficient operation and prevents the compressor from overheating, which is essential for maintaining the refrigerator's performance and longevity.
You should replace the condenser fan motor if it becomes faulty. Causes of a bad fan motor can include electrical failures, wear and tear from regular use, or blockages that cause the motor to overheat or burn out. A malfunctioning fan motor can lead to inadequate cooling, increased energy consumption, and potential damage to other refrigerator components.
Symptoms of a bad condenser fan motor include:
- The refrigerator not cooling properly
- Unusual noises coming from the back of the refrigerator
- The compressor running hot or cycling on and off frequently
- The condenser coils feeling excessively hot
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Freezer section too warm
-
Noisy
-
Fridge too warm
See more...
Do-It-Yourself Stories from Customers like You
Side by side fridge had stopped cooling in both fridge and freezer and was hot to touch in center between the two Robert P. • King , NC • August 11, 2015
I googled the issue and read several articles. Most started with cleaning the coils (which mine are on the bottom) (19yr old Kenmore 363.9557812). I had not really ever cleaned them well, vacuuming did little. I had to remove the cardboard cover off the back of the frig, and blew them clean (front to back). Once that was done, I started cleaning from the back and noticed the fan wasn't turning week (condensor fan). Blew it out too, have it a good soon with a pencil, it puffed out a bunch of...
Read more
More
$226.48
- Compare At:
-
$269.51
- You Save:
-
$43.03
Genuine Ge part
By: Ge
Part Number: WR60X114
The Evaporator Fan Blade is an OEM component for GE freezers and bottom-mount refrigerator designs. Located inside the freezer compartment, this fan blade spins to circulate cold air evenly throughout the storage space.
Causes of a faulty evaporator fan blade include natural fatigue from running year-round. Freezers exposed to humid environments may experience faster corrosion.
Symptoms include:
- Abnormal sounds like knocking or clunking from inside the walls
- cold spots developing in certain freezer areas
- Higher power bills from inefficient temperature regulation
- Frost or ice patches forming on evaporator coils
This part is also compatible with some brands like Hotpoint, RCA, and Kenmore.
Do-It-Yourself Stories from Customers like You
Broken fan blade Thomas H. • West Blocton , AL • April 21, 2014
I used a set of ring pliers to remove the old retaining ring, then spread the plastic ribs around the fan motor shaft with a small flat bladed screwdriver to ease removal of the old fan blade. I reversed the process to replace the blade, gently tapping a socket from my socket wrench set placed over the motor shaft and ribs with a small rubber mallet. I stopped when the shaft protruded about 1/8" beyond the plastic ribs of the new fan blade, then installed the new retaining clamp ring with the...
Read more
More
$17.95
- Compare At:
-
$24.40
- You Save:
-
$6.45
Genuine Ge part
By: Ge
Part Number: WR17X11349
The Ice Maker Water Line is an OEM replacement part for GE refrigerators. It is an important supply line that delivers water from the main water source to the icemaker component. The water line allows water to flow smoothly, facilitating the icemaking process.
Causes of a bad water line can include cracks or punctures from impact or bending, mineral deposits and corrosion building up inside the line restricting flow, or improper connection fittings causing leakage.
Symptoms of a bad ice maker water line include:
- Irregular or insufficient ice production
- No water delivery to the icemaker despite activation
- Noticeable leaks or drips near the water line attachment points
- Strange knocking or hammering sounds are heard when the icemaker is running
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Had a cracked plastic ice maker inlet water tube that flooded part of kitchen floor Terry C. • Durham , NC • February 16, 2019
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,...
Read more
More
$8.95
- Compare At:
-
$10.56
- You Save:
-
$1.61
Genuine Ge part
By: Ge
Part Number: WR2X8474
The Ice Maker Fill Tube Grommet is an OEM part for GE refrigerators. This grommet creates a seal between the ice maker fill tube and the refrigerator, preventing leaks and ensuring that water is properly directed into the ice maker during the filling process.
Causes of a bad grommet can include regular wear and tear, damage from exposure to freezing and thawing cycles, or degradation from exposure to water and moisture.
Symptoms of a bad ice maker fill tube grommet include:
- Water leaks around the ice maker fill tube area
- Ice maker not producing ice properly
- Visible cracks or deformation in the grommet
- Water pooling inside or around the refrigerator
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Leaking
-
Ice maker not making ice
See more...
Do-It-Yourself Stories from Customers like You
Had a cracked plastic ice maker inlet water tube that flooded part of kitchen floor Terry C. • Durham , NC • February 16, 2019
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,...
Read more
More
$32.95
- Compare At:
-
$38.88
- You Save:
-
$5.93
Genuine Ge part
By: Ge
Part Number: WR17X4310
The Ice Bucket and Auger Assembly is an OEM part for GE refrigerators. This part stores ice and includes an auger mechanism that helps dispense the ice through the refrigerator's ice dispenser.
Causes of a bad ice bucket and auger assembly include cracks in the bucket, worn or broken auger blades, or issues with the auger motor.
Symptoms of a bad ice bucket and auger assembly include:
- Ice not dispensing properly or at all
- Unusual noises when the dispenser is activated
- Visible damage to the bucket or auger
- Ice clumping or jamming in the bucket
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Refrigerator automatic ice bucket had rust on the auger helix dispenser Eric B. • Burke , VA • October 15, 2014
I ordered a new bucket and auger combination--I didn't want to have to completely disassemble the mechanism to replace the rusted auger helix dispenser, so for about twice the cost of the auger alone I got the complete assembly. The product arrived in pristine condition less than 48 hours after I purchased it online. About 10 minutes later (most of that spent taking out the old bucket and finding my philips head screwdriver), I had removed the four screws holding the cover plate on the old...
Read more
More
$268.21
- Compare At:
-
$319.17
- You Save:
-
$50.96
Genuine Ge part
By: Ge
Part Number: WR07X10055
This PTC start relay mounts on the refrigerator compressor and briefly energizes the start winding, then automatically opens as it warms. Replacing a weak relay helps restore reliable compressor starts and consistent cooling. What it does:
- Provides momentary power to the compressor's start winding at startup; the PTC element opens as it heats
- Helps ensure smooth compressor starts and reduces repeated start attempts
- Signs of a failed start device can include no cooling because the compressor won't run
- Clicking or buzzing from the compressor area every few minutes
- Compressor starts intermittently or stops shortly after starting
What's included:
- Includes: 1 PTC start relay
Install notes:
- Disconnect power and pull the refrigerator forward to access the rear service area
- Remove the rear panel to reach the compressor compartment
- Unplug the wire harness and pull the old relay straight off the compressor terminals; note its orientation
- Push the new relay fully onto the compressor prongs, reconnect the harness, reinstall the panel, and restore power
Do-It-Yourself Stories from Customers like You
The compressor was clicking on and off refrigerator was blowing hot air inside Steve F. • Sealy , TX • May 27, 2017
I bought this relay switch and it works great. On the left side of the compressor there is a plastic cover you pry off with a screw driver. The relay switch had one wire plug on it. Just pull the wire off and the pull the relay switch off the compressor.
Read more
More
$21.95
- Compare At:
-
$25.90
- You Save:
-
$3.95
Genuine Ge part
By: Ge
Part Number: WR62X26536
This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.
- Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
- Helps maintain a proper seal to limit frost and moisture around the dispenser
- Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
- Wear or sticking of the armature/spring can hinder movement and affect dispenser operation
What's included: 1 armature kit Installation notes:
- Unplug the refrigerator and shut off water to the dispenser before servicing
- Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
- Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
- Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation
Do-It-Yourself Stories from Customers like You
Water was overflowing out of the ice maker during fill process and freezing into a block of ice! Steven B. • Arlington , TX • March 17, 2015
Replaced the water supply valve...boom!
Read more
More
$52.73
- Compare At:
-
$63.28
- You Save:
-
$10.55
Genuine Ge part
By: Ge
Part Number: WR60X10262
This replacement motor powers the dispenser's auger/crusher mechanism to move ice from the bucket to the chute. Replacing a weak or seized motor helps restore reliable cube or crushed-ice dispensing from the freezer door.
- Drives the ice auger/crusher to feed ice from the bucket through the dispenser chute
- Helps deliver cubes or crushed ice, depending on the control selection
- Common symptoms: no ice dispensing, auger not turning, loud humming or grinding, intermittent or weak dispensing
- Located in the freezer-door dispenser assembly and engages the ice bucket coupler
What's included: One dispenser crusher motor. Install notes:
- Disconnect power to the refrigerator before servicing
- Remove the ice bucket and dispenser trim/panel to access the motor; note wire orientation and fasteners
- Transfer any mounting hardware or coupler from the old motor
- Reassemble, restore power, and test ice dispensing
Do-It-Yourself Stories from Customers like You
Needed new ice maker motor and circuit board Edward Z. • Berlin , CT • August 19, 2016
I watched the help videos first, then ordered the parts, and installed all items as in the video.
Read more
More
$146.95
- Compare At:
-
$174.58
- You Save:
-
$27.63
Genuine Ge part
By: Ge
Part Number: WR87X20798
$437.76
- Compare At:
-
$520.93
- You Save:
-
$83.17
Genuine Ge part
By: Ge
Part Number: WR62X107
Door solenoid with plunger.
Do-It-Yourself Stories from Customers like You
When dispensing ice from the ice maker, the solenoid was buzzing loudly. It was also rusting badly. Brian B. • Hudson , NH • March 28, 2014
I ordered a new solenoid and when it arrived, I installed it as follows: I cut the power to the refrigerator. I then pulled off the rubber boot (and it's plastic frame) that covers the water switch. Then I removed the bezel that covers the front of the ice maker controls by pulling it straight out. Then I removed the four screws found on the assembly under the bezel. After pulling the assembly forward a bit, I detached the multi-wire connector attached to it and put the assembly aside....
Read more
More
$74.34
- Compare At:
-
$88.46
- You Save:
-
$14.12
Genuine Ge part
By: Ge
Part Number: WR2X8818
The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.
- Holds the recess/ice door on its pivot within the dispenser assembly
- Helps the flapper close fully to seal the ice chute
- Restores smooth open/close action of the dispenser door
- Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute
What's included: 1 recess door retainer Install notes:
- Unplug the refrigerator before servicing the dispenser
- Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
- Note spring orientation and retainer position; transfer components to the new retainer
- Verify flapper movement and seal before reassembly and restoring power
Do-It-Yourself Stories from Customers like You
Yes ice was not coming out of the dispenser Jason S. • Goose Creek , SC • December 02, 2014
I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well.
Read more
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WR17X3089
This dispenser crank links the dispenser solenoid and the ice chute door. When you press the dispenser lever, the crank pivots to open and close the ice door so cubes or crushed ice can dispense cleanly without warm air leaking into the freezer.
- Connects the solenoid to the ice chute door to control door movement
- Helps seal the chute when not dispensing to reduce frost and moisture issues
- Common failure signs include ice door not opening/closing, constant frost around chute, or warm/moist air leakage at dispenser
- Can cause ice clumping, frost buildup, or water/ice dispensed irregularly when worn or broken
What's included: 1 dispenser crank Install notes:
- Disconnect power before servicing the dispenser area
- Access typically requires removing the dispenser front panel and trim; use care with plastic tabs and wiring
- Note linkage orientation to the solenoid and door flap before removal
- Inspect related parts for wear while open
Do-It-Yourself Stories from Customers like You
Ice build up on front of icemaker Brian H. • Mccalla , AL • August 06, 2016
REPLACED DISPENSER CRANK ARM, SPRING, FLAPPER FOR DISPENSER. THE REPAIR WAS VERY SIMPLE WITH NO PROBLEMS AT ALL.
Read more
More
$26.95
- Compare At:
-
$32.34
- You Save:
-
$5.39
Genuine Ge part
By: Ge
Part Number: WR01X10618
This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.
- Secures covers, brackets, and trim to the appliance cabinet or liner
- Replaces missing, stripped, or corroded hardware
- Helps reduce vibration noise and loose or misaligned parts
- Maintains proper fit of guards, kickplates, or internal panels
Includes: 1 screw
- Disconnect power; turn off water supply if working near water lines
- Match to the original fastener to size and thread
- Start threads by hand to avoid cross-threading; tighten snugly, not excessively
- If threading into plastic, avoid overtightening to prevent damage
Do-It-Yourself Stories from Customers like You
Water tank leak in refrigerator when using the water dispenser. Stephen B. • Summerville , SC • February 24, 2019
Replaced the water tank. Followed the video instruction provided by Appliance Parts Pros.
Very good instruction.
Read more
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WR17X4358
This water tank is the internal reservoir that stores and chills water for the refrigerator dispenser. Replacing a damaged tank helps restore proper dispenser flow and prevents water from pooling inside the fresh food compartment. What it does:
- Holds and cools drinking water inside the refrigerator before it reaches the dispenser
- Helps maintain steady dispenser flow and reduces spurting
- Typical failure symptoms: water leaking inside the fridge (often near the crisper area), visible cracks in the reservoir, or weak/no water from the dispenser after other causes are ruled out
What's included:
Install notes:
- Disconnect power and shut off the household water supply before service
- Remove interior shelves/drawers to access the tank and cover; place a towel to catch residual water
- Release tubing from quick-connect fittings; note routing and lengths, and ensure tubes are fully seated on reassembly
- Restore water, check for leaks, and dispense several cups to purge air and flush the system
Do-It-Yourself Stories from Customers like You
Nasty water tank for fridge dispenser Prather, T. • Minden , NV • September 22, 2014
This part was easy to install by following the directions from other users here. As long as you get the right hoses connected in the right places, everything else was straight forward. Takes a few minutes for the tank to initially fill and pressurize and clear the air in the line and then you're on your way to clean fresh water!
Read more
More
$110.95
- Compare At:
-
$133.14
- You Save:
-
$22.19
Genuine Ge part
By: Ge
Part Number: WR2X4754
This clamp secures small hoses or tubing and nearby wiring inside the appliance to keep lines held in place and reduce rubbing, leaks, or vibration noise. It's a direct-fit replacement designed to restore proper hose routing and stability. What it does:
- Holds water, drain or vent tubing securely to prevent sagging and rubbing that can cause leaks or wear
- Keeps hoses and wires aligned to reduce vibration and rattling during operation
- Helps maintain proper connections at fittings so seals stay seated and drip risk is minimized
- Simple mechanical clip action — no special tools or adhesives required
Install notes:
- Disconnect power and shut off the water supply before starting any repair
- Remove the old clamp and install this clamp in the same orientation; tubing sits fully in the fitting
- Use standard pliers (or the OEM-recommended tool) to compress/seat the clamp; avoid twisting or pinching the tubing
- Inspect surrounding tubing and fittings for wear; replace damaged hoses or seals if found
Do-It-Yourself Stories from Customers like You
Had a cracked plastic ice maker inlet water tube that flooded part of kitchen floor Terry C. • Durham , NC • February 16, 2019
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,...
Read more
More
$6.95
- Compare At:
-
$8.36
- You Save:
-
$1.41