Samsung Refrigerator RF265ABRS Parts

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

• Leaking
• Not dispensing water
• Noisy

Verified that the water line had flowing water, check. Removed lower screen and vacuumed and cleaned all dust. Proceeded to test water flow to the valve and beyond the valve. The valve did not allow water to pass through it. Nor would it open or close. Went to Marbeck for confirmation and was sent to your website for the part. Read more

Order a new fixer Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

• Fridge too warm

Replaced relay and worked perfectly. Thanks for the fast service. Read more

I looked at the blow up drawing to figure out what parts I might need. I then watched a you tube video to see how to take the handle off. I kind of figured out on my own how to remove the ruined cap handle. It took me a few minutes to figure it out and more time to remove both the handle and the broken part. Turns out I did not need the spring nor the shaft cap handle. Very proud of myself. Saved a huge amount of money. Only problem was that I could only put in one screw as the previous... Read more

Repair required removing all of the interior drawers & shelves and the interior back panel. There you will find the defrost heater. Behind the defrost heater is a metal plate as well as one on the back of the front interior cover. Both were corroded and in need of replacement. I ordered Samsung part #’s AP5577767, plate drain & AP5587916, evaporator plate and replaced both. Read more

Replaced original parts- Only skill needed was finding plastic push tabs. No tools required. Most of time was used for removing food from refrigerator before looking for tabs. Read more

Removed the bottom shelf by releasing the 2 clips near the water filter, then lifted the front of the shelf and slid it out. Removed 2 screws from the broken Vegetable Rail and replaced it with the new one. Slid the shelf back into place and locked it down into the clips. Done. Took longer to remove everything from the shelf than it did to fix it. Less than 5 minute repair. Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

I removed the broken rail saving the 2 Phillips head screws for installation of new drawer rail. Removal of the shelf above the drawers was required and was accomplished by pushing a button on the front of the shelf support. The installation was a snap and took about 10 minutes after removal of food items. The part was the correct one as verified by the model number on the inside of the refrigerator door. Thanks AppliancePartsPros.com! Read more

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

Removed broken piece, installed new piece. Read more

Removed the plastic glass from the broken front and put into the new one. It took about a total of 10 minutes. It was pretty easy. Read more

I looked at the blow up drawing to figure out what parts I might need. I then watched a you tube video to see how to take the handle off. I kind of figured out on my own how to remove the ruined cap handle. It took me a few minutes to figure it out and more time to remove both the handle and the broken part. Turns out I did not need the spring nor the shaft cap handle. Very proud of myself. Saved a huge amount of money. Only problem was that I could only put in one screw as the previous... Read more