Samsung Refrigerator RF4289HBRS Parts

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

First, I modified old butter knife by bending a 90° angle about 3/4" from the tip. I slid the bent in up under the bottom of the switch cover and worked it to one side. I then rotated the knife downward using the bent end to pry the cover off. The switch is held by plastic arms on each side. The bottom right arm has a locating pin that fits into the switch. Unplugged the switch and re-installed. Read more

I have a large Samsung 4 door refrigerator. One of the rear wheels broke. To replace it, you need the wheel and the shaft. To lift the refrigerator for the repair, I had my wife stand in front of it with her foot on a board that was wedged against the front wheels. I then pushed the refrigerator up from behind and slid a 3/4" piece of plywood underneath the bottom with my foot. This gives you enough space to do the repair. After removing the back cover, it's best just to knock out the broken... Read more

• Not dispensing water

Purchased both the ice maker assembly and the valve assembly to replace the parts as needed. replaced the ice maker assembly first, and this fixed my problem. Took about 10 minutes, mainly because I didn't watch the YouTube video first. Had I watched that, it would have probably taken even less time. One Philips head screw driver is all you need. Read more

I removed the door and the hinge assembly from the right side; it turns out the grommet had never been installed and this is what was causing the door to grind down the metal hinge. It was remarkably easy to replace and my door is working perfectly! Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

I replaced the temperature sensor, the thermo fuse, and the heating element that thaws the evaporator on a cycle to keep the evaporator from freezing up. The most time consuming part of the repair was waiting for the fridge to thaw out so that I could remove the cover. I disconnected the fridge the night before and placed a fan on low with the doors open so that it was thawed out when I awoke. It was easy to remove the evaporator cover once I removed all of the shelves. I took pics as i was... Read more

Had to take the handle off & replace the plastic piece that the handle is attached to. The part had to be modified slightly & had to pick up new mount holes. The part is on and works fine. Thank you for everything. Read more

Replaced cap handle. Repair took less than 5 minutes. Read more

I started by replacing the water filter assembly since it was leaking after I attempted to install a non-name-brand filter. The new assembly didn't fix the problem (but was hard to find, and AppliancePartsPros was amazing in being able to get one). Further, while replacing that I noticed that the previous owner had literally cut out the grounding pin from the power cord. I decided to replace the power cord and the Ice Maker Assembly. None of the online stores seemed to have either part listed... Read more

Replaced the condenser fan. Read more

I replaced the control board and the microswitch. Read more

Replaced cap handle. Repair took less than 5 minutes. Read more

Purchased two new gaskets and replaced them. Hoping upper door will seal better and will pull open a little harder then before.Right now it pulls open very easy and I feel that it should pull harder. The freezer seems to be a lot better with little to no ice forming. I have been looking for information to see if there is something to put on gasket to make the pull on the door a little harder. Any suggestions would be greatly appreciated. ... Read more

Used the video with the parts and replaced the wheels. The only thing we did wrong was using the front wheel axle instead of the back wheel axle on the back wheels. I will just order two more front wheel axles which are longer than the back axle. Thank you for the video, it made this repair easier. Read more