Samsung Refrigerator RFG295ABRS Parts

• Light not working

Perfect, everything works now Read more

Ordered the two motors plus ordered the fan blades since I was afraid one might break during replacement. Changed out without breaking Freezer and both ice makers now working fine Read more

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

I have a large Samsung 4 door refrigerator. One of the rear wheels broke. To replace it, you need the wheel and the shaft. To lift the refrigerator for the repair, I had my wife stand in front of it with her foot on a board that was wedged against the front wheels. I then pushed the refrigerator up from behind and slid a 3/4" piece of plywood underneath the bottom with my foot. This gives you enough space to do the repair. After removing the back cover, it's best just to knock out the broken... Read more

• Not dispensing water

Purchased both the ice maker assembly and the valve assembly to replace the parts as needed. replaced the ice maker assembly first, and this fixed my problem. Took about 10 minutes, mainly because I didn't watch the YouTube video first. Had I watched that, it would have probably taken even less time. One Philips head screw driver is all you need. Read more

• Noisy

I bought new parts, motor and fan. Replace the old one. Took me no more than 15 minutes to fix it. Read more

The Samsung french door freezer has a handle that has plastic pivot plates that help "push" the door open during its first inch or so of travel. One morning, the handle pulled off taking portions of both pivot plates with it! The parts from AppliancePros arrived very quickly, and the repair required re-positioning the mounting holes, even thought the replacement parts looked identical to what was left of the pivot plates. Okay, that‘s not AppliancePros fault in any way whatsoever; this happens... Read more

I removed the door and the hinge assembly from the right side; it turns out the grommet had never been installed and this is what was causing the door to grind down the metal hinge. It was remarkably easy to replace and my door is working perfectly! Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

There's a piece of plastic with an embedded metal nut that is screwed on to the handle at both ends of the handle. These nuts lock on to screws on the drawer. Problem is that these plastic parts are flimsy and they broke at both the left and right ends and the handle just came loose. It was a two minute job to unscrew these plastic parts from the handle and screw in the replacements. Once that's done you can attach the handle to the drawer (need a hex key). Read more

Used the video with the parts and replaced the wheels. The only thing we did wrong was using the front wheel axle instead of the back wheel axle on the back wheels. I will just order two more front wheel axles which are longer than the back axle. Thank you for the video, it made this repair easier. Read more

The Samsung french door freezer has a handle that has plastic pivot plates that help "push" the door open during its first inch or so of travel. One morning, the handle pulled off taking portions of both pivot plates with it! The parts from AppliancePros arrived very quickly, and the repair required re-positioning the mounting holes, even thought the replacement parts looked identical to what was left of the pivot plates. Okay, that‘s not AppliancePros fault in any way whatsoever; this happens... Read more

Order a new fixer Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

Removed the old shelf and replaced it with the new one. Less than two minutes. Read more

Ordered tank and heater, installed, so far so good. Thanks for the speedy order Roman Read more