Samsung Refrigerator RFG296HDBPXAA Parts

I replaced the control board and the microswitch. Read more

Order a new fixer Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

I looked at the blow up drawing to figure out what parts I might need. I then watched a you tube video to see how to take the handle off. I kind of figured out on my own how to remove the ruined cap handle. It took me a few minutes to figure it out and more time to remove both the handle and the broken part. Turns out I did not need the spring nor the shaft cap handle. Very proud of myself. Saved a huge amount of money. Only problem was that I could only put in one screw as the previous... Read more

• Fridge too cold
• Fridge too warm

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

Removed the bottom shelf by releasing the 2 clips near the water filter, then lifted the front of the shelf and slid it out. Removed 2 screws from the broken Vegetable Rail and replaced it with the new one. Slid the shelf back into place and locked it down into the clips. Done. Took longer to remove everything from the shelf than it did to fix it. Less than 5 minute repair. Read more

I removed the broken rail saving the 2 Phillips head screws for installation of new drawer rail. Removal of the shelf above the drawers was required and was accomplished by pushing a button on the front of the shelf support. The installation was a snap and took about 10 minutes after removal of food items. The part was the correct one as verified by the model number on the inside of the refrigerator door. Thanks AppliancePartsPros.com! Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

I looked at the blow up drawing to figure out what parts I might need. I then watched a you tube video to see how to take the handle off. I kind of figured out on my own how to remove the ruined cap handle. It took me a few minutes to figure it out and more time to remove both the handle and the broken part. Turns out I did not need the spring nor the shaft cap handle. Very proud of myself. Saved a huge amount of money. Only problem was that I could only put in one screw as the previous... Read more

The circulating fan stopped. Fairly easy to fix, but only after watching Appliancepartspros video. Had to let frig. set for a day to thaw out. Time to fix obviously does not include thaw time or waiting for parts to arrive from Appliancepartspros. Fortunately, I had a backup frig. in the garage. Read more

Removed Phillips head screw from bottom side. Next I removed front electronic interface panel, carefully. The plastic clips holding it in place are designed to pop lose on the right side first.then unplug wiring from back of interface panel. Remove two Phillips head screws holding ice/water dispensing unit in place. Carefully remove dispensing unit from leaving multiple wiring plugs connected. Carefully apply pressure to the side of the ice chute door frame to remove the ice chute door/flap.... Read more

Using service manual, obtained from this site, I verified with meter that this was the error. I ordered the defrost sensor. The part arrived the next day. Most of the time to repair was unloading, cleaning, and reloading the refrigerator. Read more

New flap housing with a new spring and the new replaceable guide. I didn't know the screw to hold the guide to the housing and forgot to add the spring bushing to my cart during checkout. It was pretty simple, only reason I didn't give it an easy rating is because having to pop off the hinge caps was making me think I was going to snap some of the cheap plastic, kinda have to be careful Read more

I ordered 3 replacement shelves for my fridge. Promptly received the shipment, but one of the items was damaged (the lid for the butter try shelf). I went online and started a chat with the rep from APP, and they were great. Gave them my information and told them the issue. Replacement part sent out on Monday! Great service. Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more