Samsung Refrigerator RS27T5202SR Parts

The repair itself is pretty basic, remove broken parts and replace with new, but the process is much more challenging on the freezer door than on the fridge side since the water lines are routed through the hinge. This is definitely a two person job and you will be laying on the floor to do it. 1st thing is to turn the water off and remove the ice bucket. Remove top trim piece and release upper hinge assembly, support the door. The top hinge must rotate up to slip over the wiring bundle,... Read more

Found one of the drain valves was clogged causing condensation to overflow on the floor behind the refrigerator. Order the parts on Monday morning and they arrived tuesday afternoon. Replace both of the valves in 15 minutes. Easy repair and save a bundle over a service call. Read more

First, I modified old butter knife by bending a 90° angle about 3/4" from the tip. I slid the bent in up under the bottom of the switch cover and worked it to one side. I then rotated the knife downward using the bent end to pry the cover off. The switch is held by plastic arms on each side. The bottom right arm has a locating pin that fits into the switch. Unplugged the switch and re-installed. Read more

I have a large Samsung 4 door refrigerator. One of the rear wheels broke. To replace it, you need the wheel and the shaft. To lift the refrigerator for the repair, I had my wife stand in front of it with her foot on a board that was wedged against the front wheels. I then pushed the refrigerator up from behind and slid a 3/4" piece of plywood underneath the bottom with my foot. This gives you enough space to do the repair. After removing the back cover, it's best just to knock out the broken... Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

Replaced ice maker Read more

I started by replacing the water filter assembly since it was leaking after I attempted to install a non-name-brand filter. The new assembly didn't fix the problem (but was hard to find, and AppliancePartsPros was amazing in being able to get one). Further, while replacing that I noticed that the previous owner had literally cut out the grounding pin from the power cord. I decided to replace the power cord and the Ice Maker Assembly. None of the online stores seemed to have either part listed... Read more

Replaced the condenser fan. Read more

Used the video with the parts and replaced the wheels. The only thing we did wrong was using the front wheel axle instead of the back wheel axle on the back wheels. I will just order two more front wheel axles which are longer than the back axle. Thank you for the video, it made this repair easier. Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

Unplug all the plugs to the main control board and switched to the new control board. Works perfect thank you. These days you have to do stuff yourself. Everything is getting so expensive. AppliancePartsPros customer service was 100% good. Gave me the right parts thank you again and again. Read more

Ordered leg. Cover and magnet switch. I did not need magnet switch, it came on the new leg cover. Read more

Replaced the hinge cam riser. As suggested I replaced hinge cam risers for both doors. Read more

Ordered a new one and replaced it. Read more